Tools for pressing — Guide pillars — Part 2: Type A, straight pillars

ISO 9182-2;2013 specifies the dimensions and tolerances, in millimetres, of guide pillars, type A, intended for use in press tools. These guide pillars can be straight, type A1, or straight with end-locking and locking ring, type A2. It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet its requirements.

Outillage de presse — Colonnes de guidage — Partie 2: Type A, colonnes droites

L'ISO 9182-2:2013 spécifie les dimensions et tolérances, en millimètres, des colonnes de guidage, type A, destinées à être utilisées dans des outillages de presse. Ces colonnes peuvent être soit uniquement droites, type A1, soit en plus, à retenue inférieure avec jonc, type A2. Elle donne des indications relatives aux matériaux, spécifie une dureté et spécifie la désignation des colonnes de guidage conformes à l'ISO 9182-2:2013.

General Information

Status
Withdrawn
Publication Date
10-Dec-2013
Current Stage
9599 - Withdrawal of International Standard
Completion Date
15-Aug-2023
Ref Project

Relations

Buy Standard

Standard
ISO 9182-2:2013 - Tools for pressing -- Guide pillars
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 9182-2:2013 - Outillage de presse -- Colonnes de guidage
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 9182-2
Second edition
2013-12-15
Tools for pressing — Guide pillars —
Part 2:
Type A, straight pillars
Outillage de presse — Colonnes de guidage —
Partie 2: Type A, colonnes droites
Reference number
ISO 9182-2:2013(E)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 9182-2:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 9182-2:2013(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Dimensions . 1
3 Material . 3
4 Designation . 3
Bibliography . 4
© ISO 2013 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 9182-2:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning
...

NORME ISO
INTERNATIONALE 9182-2
Deuxième édition
2013-12-15
Outillage de presse — Colonnes de
guidage —
Partie 2:
Type A, colonnes droites
Tools for pressing — Guide pillars —
Part 2: Type A, straight pillars
Numéro de référence
ISO 9182-2:2013(F)
©
ISO 2013

---------------------- Page: 1 ----------------------
ISO 9182-2:2013(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2013
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur
l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à
l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2013 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 9182-2:2013(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Dimensions . 1
3 Matériau . 3
4 Désignation . 3
Bibliographie . 4
© ISO 2013 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 9182-2:2013(F)

Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (CEI) en ce qui concerne
la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/CEI, Partie 1. Il convient, en particulier de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/CEI, Partie 2 (voir www.
iso.org/directives).
L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les
références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l’élaboration
du document sont indiqués dans l’Introduction et/ou sur la liste ISO des déclarations de brevets reçues
(voir www.iso.org/patents).
Les éventuelles appellations commerciales utilisées dans le présent document sont données pour
information à l’intention des utilisateurs et ne constituent pas une approbation ou une recommandation.
Pour une explication de la signification des termes et expressions
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.