ISO 7299-1:2007

Diesel engines — End-mounting flanges for pumps — Part 1: Fuel injection pumps

ISO 7299-1:2006 specifies dimensional requirements for nine types of end-mounting flanges for fuel injection pumps (rotary, distributor and in-line fuel injection pumps) for use in diesel (compression-ignition) engines.

Moteurs diesels — Brides de montage des pompes — Partie 1: Pompes d'injection de carburant

General Information

• Status: Published
• Publication Date: 09-Jan-2007
• ICS: 43.060.40 - Fuel systems
• Technical Committee: ISO/TC 22/SC 34 - Propulsion, powertrain and powertrain fluids
• Drafting Committee: ISO/TC 22/SC 34 - Propulsion, powertrain and powertrain fluids

Relations

• Revises: ISO 7299:1996 - Diesel engines — End-mounting flanges for fuel injection pumps
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 7299-1
First edition
2007-02-01

Diesel engines — End-mounting flanges
for pumps —
Part 1:
Fuel injection pumps
Moteurs diesels — Brides de montage des pompes —
Partie 1: Pompes d'injection de carburant



Reference number
ISO 7299-1:2007(E)
©
ISO 2007

---------------------- Page: 1 ----------------------
ISO 7299-1:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 7299-1:2007(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Dimensions and tolerances . 1
3.1 General. 1
3.2 Fuel injection pumps. 2

© ISO 2007 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 7299-1:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7299-1 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 7, Injection
equipment and filters for use on road vehicles.
This first edition, together with the first edition of ISO 7299-2, cancels and replaces the second edition of
ISO 7299 (ISO 7299:1996), which has been technically revised.
ISO 7299 consists of the following parts, under the general title Diesel engines — End-mounting flanges for
pumps:
⎯ Part 1: Fuel injection pumps
⎯ Part 2: High-pressure supply pumps for common rail fuel injection systems


iv © ISO 2007 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 7299-1:2007(E)

Diesel engines — End-mounting flanges for pumps —
Part 1:
Fuel injection pumps
1 Scope
This International Standard specifies dimensional requirements for nine types of end-mounting flanges for fuel
injection pumps (rotary, distributor and in-line fuel injection pumps) for use in diesel (compression-ignition)
engines.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO
...