ISO 6519:2023

Diesel engines - Fuel injection pumps - Tapers for shaft ends and hubs

This document specifies the dimensions of tapered shaft ends and hubs of fuel injection pumps and high-pressure supply pumps for diesel (compression-ignition) engines. The specified shaft ends and hubs can be used with or without keys. NOTE The specified shaft ends and hubs can also be used for other applications where no specific standards exist.

Moteurs diesels — Pompes d'injection de combustible — Cônes pour bouts d'arbre et moyeux

General Information

• Status: Published
• Publication Date: 22-Jun-2023
• ICS: 43.060.40 - Fuel systems
• Technical Committee: ISO/TC 22/SC 34 - Propulsion, powertrain and powertrain fluids
• Drafting Committee: ISO/TC 22/SC 34 - Propulsion, powertrain and powertrain fluids
• Current Stage: 6060 - International Standard published
• Start Date: 23-Jun-2023
• Due Date: 22-Oct-2023
• Completion Date: 23-Jun-2023

Relations

• Revises: ISO 6519:2015 - Diesel engines - Fuel injection pumps - Tapers for shaft ends and hubs
• Effective Date: 06-Jun-2022

Overview

ISO 6519:2023 - Diesel engines - Fuel injection pumps - Tapers for shaft ends and hubs - specifies the dimensional and tolerance requirements for tapered shaft ends and mating hubs used on fuel injection pumps and high‑pressure supply pumps for diesel (compression‑ignition) engines. Published as the fifth edition in 2023, this ISO standard defines types of shaft ends and hub keyways to ensure reliable mechanical connection, interchangeability and correct assembly. The specified tapers may be used with or without keys and are also applicable to other equipment where no specific standard exists.

Key topics and requirements

• Scope: Dimensions and tolerances for tapered shaft ends and hubs for diesel fuel injection and high‑pressure supply pumps.
• Shaft end types: The standard contains multiple shaft end designs (notably types 1, 2 and 3), including options for threaded ends and manufacturing features (e.g., clamping collars).
• Hub keyways and cones: Keyway profiles, hub cone lengths and assembly requirements are specified so the mating faces and fixing nuts can be correctly engaged after assembly. For some key/slot details (type 3) the standard allows agreement between supplier and purchaser.
• Dimensions and tolerances: Detailed dimension tables and figures define nominal sizes, length limits and tolerance classes to ensure seating contact begins at the major diameter and that taper drive functions satisfactorily.
• Editorial notes: The 2023 edition supersedes ISO 6519:2015, adding shaft end specifications and correcting technical descriptions. The document contains no normative external references and lists ISO 3912 (Woodruff keys) in the bibliography.

Applications and users

Who benefits:

• Pump and engine manufacturers ensuring mechanical compatibility between pump shafts and engine drives.
• Design and mechanical engineers specifying mating parts, tolerances and assembly clearances.
• Production and quality control teams using the standard for inspection, gauges and acceptance criteria.
• Maintenance and repair professionals replacing pumps or designing retrofit couplings. Practical uses:
• Standardizing tapered shaft and hub dimensions for interchangeability across suppliers.
• Guiding machining and assembly of pump drive connections to minimize misalignment and ensure repeatable engagement.
• Defining keyway options and tolerance agreements for custom or legacy equipment.

Related standards

• ISO 3912 - Woodruff keys and keyways (referenced in the bibliography for key-related applications)

Keywords: ISO 6519:2023, diesel engines, fuel injection pumps, tapered shaft ends, hubs, tapers, dimensions, tolerances, keyways, pump shaft standards.

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 6519
Fifth edition
2023-06
Diesel engines — Fuel injection pumps
— Tapers for shaft ends and hubs
Moteurs diesels — Pompes d'injection de combustible — Cônes pour
bouts d'arbre et moyeux
Reference number
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions and tolerances .1
4.1 General . 1
4.2 Shaft ends with taper . 1
4.3 Keyways of hub with taper . 4
Bibliography . 6
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the W
...