Assembly tools for screws and nuts — Ratcheting wrenches — Technical requirements

This document specifies the dimensions and technical requirements for ratcheting wrenches used in assembly or disassembly of hexagonal and double hexagonal fasteners. NOTE The wrenches covered by this document are the ones identified in ISO 1703 under reference No.1 1 01 07 0, 1 1 01 08 0, 1 1 01 09 0 and 1 1 02 19 0, 1 1 02 20 0. NOTE The wrenches according to this document are not intended for uses with impact stress of the wrench.

Outils de manoeuvre pour vis et écrous — Clé à cliquet — Exigences techniques

Le présent document spécifie les dimensions et les exigences techniques des clés à cliquet utilisées pour le montage et le démontage des éléments de fixation hexagonaux et hexagonaux doubles. NOTE 1 Les clés couvertes par le présent document sont identifiées dans l'ISO 1703:2018 sous les numéros de référence 1 1 01 07 0, 1 1 01 08 0, 1 1 01 09 0 et 1 1 02 19 0, 1 1 02 20 0. NOTE 2 Les clés conformes à la présente norme ne sont pas destinées à être utilisées comme clé à choc

General Information

Status
Published
Publication Date
28-Jul-2020
Current Stage
6060 - International Standard published
Start Date
29-Jul-2020
Due Date
05-Dec-2020
Completion Date
29-Jul-2020
Ref Project

Buy Standard

Standard
ISO 21982:2020 - Assembly tools for screws and nuts -- Ratcheting wrenches -- Technical requirements
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 21982:2020 - Outils de manoeuvre pour vis et écrous -- Clé à cliquet -- Exigences techniques
French language
11 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 21982 - Assembly tools for screws and nuts -- Ratcheting wrenches -- Technical requirements
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 21982
First edition
2020-07
Assembly tools for screws and nuts —
Ratcheting wrenches — Technical
requirements
Outils de manoeuvre pour vis et écrous — Clé à cliquet — Exigences
techniques
Reference number
ISO 21982:2020(E)
©
ISO 2020

---------------------- Page: 1 ----------------------
ISO 21982:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 21982:2020(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Dimension . 5
5.1 Dimensions of combination wrenches, ratcheting. 5
5.2 Dimensions of double-headed box wrenches, ratcheting . 6
6 Hardness . 7
7 Reversing torque testing . 8
8 Torque testing . 8
9 Drop testing . 8
10 Function . 8
11 Cycle testing . 8
12 Test sequence . 9
13 Designation . 9
14 Marking . 9
Annex A (informative) Recommended combinations .10
Bibliography .11
© ISO 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 21982:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10,
Assembly tools for screws and nuts, pliers and nippers.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 21982:2020(E)
Assembly tools for screws and nuts — Ratcheting wrenches
— Technical requirements
1 Scope
This document specifies the dimensions and technical requirements for ratcheting wrenches used in
assembly or disassembly of hexagonal and double hexagonal fasteners.
NOTE The wrenches covered by this document are the ones identified in ISO 1703 under reference
No.1 1 01 07 0, 1 1 01 08 0, 1 1 01 09 0 and 1 1 02 19 0, 1 1 02 20 0.
NOTE The wrenches according to this document are not intended for uses with impact stress of the wrench.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 691, Assembly tools for screws and nuts — Wrench and socket openings — Tolerances for general use
ISO 1711-1:2019, Assembly tools for screws and nuts — Technical specifications — Part 1: Hand-operated
wrenches and sockets
ISO 3318, Assembly tools for screws and nuts — Open-ended wrenches, box wrenches and combination
wrenches — Maximum widths of heads
ISO 6507-1, Metallic materials — Vickers hardness test — Part 1: Test method
ISO 6508-1, Metallic materials — Rockwell hardness test — Part 1: Test method
ISO 7738, Assembly tools for screws and nuts — Combination wrenches — Lengths of wrenches and
maximum thickness of heads
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
reversing torque
torque required to rotate the box-head ratchet of the wrench in the opposite direction to the direction
of torque application
3.2
reversing device
part of a reversible ratchet that allows the direction of torque application to be changed by the
movement of a lever or similar
© ISO 2020 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 21982:2020(E)

4 Classification
Ratcheting wrenches to which this document applies are classified as combination wrenches, ratcheting
and double-headed box wrenches, ratcheting (for recommended combinations of the wrench structures,
see Annex A).
a) Combination wrenches, ratcheting (Type I, see Figure 1):
1) Class A: flat shape;
2) Class B: offset shape with reversing device;
3) Class C: flat shape w
...

NORME ISO
INTERNATIONALE 21982
Première édition
2020-07
Outils de manoeuvre pour vis et
écrous — Clé à cliquet — Exigences
techniques
Assembly tools for screws and nuts — Ratcheting wrenches —
Technical requirements
Numéro de référence
ISO 21982:2020(F)
©
ISO 2020

---------------------- Page: 1 ----------------------
ISO 21982:2020(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2020
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2020 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 21982:2020(F)

Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Classification . 2
5 Dimension . 4
5.1 Dimensions des clés mixtes, à cliquet . 4
5.2 Dimensions des clés polygonales à double tête, à cliquet . 5
6 Dureté . 6
7 Couple d'essai de reprise . 7
8 Couple d'essai . 8
9 Essai de chûte . 8
10 Fonction . 8
11 Essais cycliques . 8
12 Séquence d'essai . 8
13 Désignation . 9
14 Marquage . 9
Annexe A (informative) Combinaisons recommandées .10
Bibliographie .11
© ISO 2020 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 21982:2020(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 29, Petit outillage, sous-comité SC 10,
Outils de manoeuvre pour vis et écrous, pinces et tenailles.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www .iso .org/ members .html.
iv © ISO 2020 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 21982:2020(F)
Outils de manoeuvre pour vis et écrous — Clé à cliquet —
Exigences techniques
1 Domaine d'application
Le présent document spécifie les dimensions et les exigences techniques des clés à cliquet utilisées pour
le montage et le démontage des éléments de fixation hexagonaux et hexagonaux doubles.
NOTE 1 Les clés couvertes par le présent document sont identifiées dans l'ISO 1703:2018 sous les numéros de
référence 1 1 01 07 0, 1 1 01 08 0, 1 1 01 09 0 et 1 1 02 19 0, 1 1 02 20 0.
NOTE 2 Les clés conformes à la présente norme ne sont pas destinées à être utilisées comme clé à choc
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s'applique (y compris les
éventuels amendements).
ISO 691, Outils de manoeuvre pour vis et écrous — Ouvertures de clés et d'embouts de serrage — Tolérances
d'usage courant
ISO 1711-1:2019, Outils de manoeuvre pour vis et écrous — Spécifications techniques — Partie 1: Clés de
serrage et douilles à main
ISO 3318, Outils de manoeuvre pour vis et écrous — Clés à fourche, clés polygonales et clés mixtes —
Largeurs maximales d'encombrement des têtes
ISO 6507-1, Matériaux métalliques — Essai de dureté Vickers — Partie 1: Méthode d'essai
ISO 6508-1, Matériaux métalliques — Essai de dureté Rockwell — Partie 1: Méthode d'essai
ISO 7738, Outils de manoeuvre pour vis et écrous — Clés mixtes de serrage — Longueurs des clés et
épaisseurs maximales des têtes
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions suivants s'appliquent.
L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l'adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l'adresse http:// www .electropedia .org/
3.1
couple de reprise
couple nécessaire pour faire tourner la clé polygonale à cliquet dans le sens opposé au sens d'application
du couple
© ISO 2020 – Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 21982:2020(F)

3.2
cliquet réversible
cliquet qui permet de changer le sens d'application du couple par le mouvement d'un levier ou d'un outil
similaire
4 Classification
Les clés à cliquet auxquelles le présent document s'applique sont classées comme clés mixtes, à cliquet
et clés polygonales doubles, à cliquet (Pour les combinaisons recommandées des structures de clés, voir
Annexe A).
a) Clés mixtes, à cliquet (Type I, voir Figure 1):
1) Classe A: forme plate;
2) Classe B: forme inclinée avec dispositif d'inversion;
3) Classe C: forme plate avec tête flexible;
b) Clés polygonales à do
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 21982
ISO/TC 29/SC 10
Assembly tools for screws and nuts —
Secretariat: DIN
Ratcheting wrenches — Technical
Voting begins on:
2020­04­29 requirements
Voting terminates on:
Outils de manoeuvre pour vis et écrous — Clé à cliquet — Exigences
2020­06­24
techniques
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 21982:2020(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2020

---------------------- Page: 1 ----------------------
ISO/FDIS 21982:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH­1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 21982:2020(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Dimension . 5
5.1 Dimensions of combination wrenches, ratcheting. 5
5.2 Dimensions of double-headed box wrenches, ratcheting . 6
6 Hardness . 7
7 Reversing torque testing . 8
8 Torque testing . 8
9 Drop testing . 8
10 Function . 8
11 Cycle testing . 8
12 Test sequence . 9
13 Designation . 9
14 Marking . 9
Annex A (informative) Recommended combinations .10
Bibliography .11
© ISO 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/FDIS 21982:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non­governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10,
Assembly tools for screws and nuts, pliers and nippers.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 21982:2020(E)
Assembly tools for screws and nuts — Ratcheting wrenches
— Technical requirements
1 Scope
This document specifies the dimensions and technical requirements for ratcheting wrenches used in
assembly or disassembly of hexagonal and double hexagonal fasteners.
NOTE The wrenches covered by this document are the ones identified in ISO 1703 under reference
No.1 1 01 07 0, 1 1 01 08 0, 1 1 01 09 0 and 1 1 02 19 0, 1 1 02 20 0.
NOTE The wrenches according to this document are not intended for uses with impact stress of the wrench.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 691, Assembly tools for screws and nuts — Wrench and socket openings — Tolerances for general use
ISO 1711­1:2019, Assembly tools for screws and nuts — Technical specifications — Part 1: Hand-operated
wrenches and sockets
ISO 3318, Assembly tools for screws and nuts — Open-ended wrenches, box wrenches and combination
wrenches — Maximum widths of heads
ISO 6507­1, Metallic materials — Vickers hardness test — Part 1: Test method
ISO 6508­1, Metallic materials — Rockwell hardness test — Part 1: Test method
ISO 7738, Assembly tools for screws and nuts — Combination wrenches — Lengths of wrenches and
maximum thickness of heads
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
reversing torque
torque required to rotate the box-head ratchet of the wrench in the opposite direction to the direction
of torque application
3.2
reversing device
part of a reversible ratchet that allows the direction of torque application to be changed by the
movement of a lever or similar
© ISO 2020 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO/FDIS 21982:2020(E)

4 Classification
Ratcheting wrenches to which this document applies are classified as combination
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.