ISO/IEC 10373-6:2001/Amd 5:2007

Identification cards — Test methods — Part 6: Proximity cards — Amendment 5: Bit rates of fc/64, fc/32 and fc/16

Cartes d'identification — Méthodes d'essai — Partie 6: Cartes de proximité — Amendement 5: Débits binaires de fc/64, fc/32 et fc/16

General Information

• Status: Withdrawn
• Publication Date: 10-Oct-2007
• Withdrawal Date: 10-Oct-2007
• ICS: 35.240.15 - Identification cards. Chip cards. Biometrics
• Technical Committee: ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification
• Drafting Committee: ISO/IEC JTC 1/SC 17/WG 8 - Integrated circuit cards without contacts
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 07-Jan-2011

Relations

• Revised: ISO/IEC 10373-6:2011 - Identification cards — Test methods — Part 6: Proximity cards
• Effective Date: 26-Sep-2008
• Amends: ISO/IEC 10373-6:2001 - Identification cards — Test methods — Part 6: Proximity cards
• Effective Date: 06-Jun-2022
• Child: ISO/IEC 10373-6:2001 - Identification cards — Test methods — Part 6: Proximity cards
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 10373-6
First edition
2001-05-15
AMENDMENT 5
2007-10-15

Identification cards — Test methods —
Part 6:
Proximity cards
AMENDMENT 5: Bit rates of fc/64, fc/32 and
fc/16
Cartes d'identification — Méthodes d'essai —
Partie 6: Cartes de proximité
AMENDEMENT 5: Débits binaires de fc/64, fc/32 et fc/16




Reference number
ISO/IEC 10373-6:2001/Amd.5:2007(E)
©
ISO/IEC 2007

---------------------- Page: 1 ----------------------
ISO/IEC 10373-6:2001/Amd.5:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO/IEC 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2007 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 10373-6:2001/Amd.5:2007(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
Amendment 5 to ISO/IEC 10373-6:2001 was prepared by Joint Technical Committee ISO/IEC JTC 1,
Information technology, Subcommittee SC 17, Cards and personal identification.


© ISO/IEC 2007 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 10373-6:2001/Amd.5:2007(E)

Identification cards — Test methods —
Part 6:
Proximity cards
AMENDMENT 5: Bit rates of fc/64, fc/32 and fc/16

Page 2, 7.1.1 of ISO/IEC 10373-6:2001/Amd.2:2003
Add the following note at the end of the subclause:
"NOTE No load modulation test is required for bit rates of fc/64, fc/32 and fc/16."
Page 4, 7.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003
Replace the existing text with the following:
"Tables 1 to 4 define additional test conditions to be applied for type A PICCs for different bit rates.
NOTE The definitions for timing parameters related to the amplitude are different between fc/128 and higher bit rates,
see the future Amendment 2 to ISO/IEC 14443-2:2001."
Page 4, 7.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003
Replace the title of Table 1 with the following: "Table 1 – Additional test conditions for a bit rate of fc/128"
Page 4, 7.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003
Insert the following table and note after Table 1:
Table 2 — Additional test conditions for a bit rate of fc/64
H
Condition t1 t2 t3 a
(A/m)
1 1,5 20/fc 14/fc 6/fc 0,2
2 1,5 20/fc 16/fc 7/fc ≤ 0,05
3 4,5 20/fc 14/fc 6/fc 0,2
4 4,5 20/fc 16/fc 7/fc ≤ 0,05
5 7,5 20/fc 14/fc 6/fc 0,2
6 7,5 20/fc 16/fc 7/fc ≤ 0,05

NOTE The timing t3 for all higher bit rates is defined in 8.1.2.2.
Page 4, 7.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003
Insert the following table after the new Table 2:
© ISO/IEC 2007 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO/IEC 10373-6:2001/Amd.5:2007(E)
Table 3 — Additional test conditions for a bit rate of fc/32
H
Condition t1 t2 t3 a
(A/m)
1 1,5 10/fc 6/fc 6/fc 0,35
2 1,5 10/fc 7/fc 7/fc ≤ 0,15
3 4,5 10/fc 6/fc 6/fc 0,35
4 4,5 10/fc 7/fc 7/fc ≤ 0,15
5 7,5 10/fc 6/fc 6/fc 0,35
6 7,5 10/fc 7/fc 7/fc ≤ 0,15

Page 4, 7.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003
Insert the following table after Table 3:
Table 4 — Additional test conditions for a bit rate of fc/16
H
Condition t1 t2 t3 a
(A/m)
1 1,5 5/fc 3/fc 6/fc 0,6
2 1,5 5/fc 3/fc 7/fc ≤ 0,3
3 4,5 5/fc 3/fc 6/fc 0,6
4 4,5 5/fc 3/fc 7/fc ≤ 0,3
5 7,5 5/fc 3/fc 6/fc 0,6
6 7,5 5/fc 3/fc 7/fc ≤ 0,3

Page 4, 7.2.2.1 of ISO/IEC 10373-6:2001/Amd.2:2003
Replace the existing text with the following:
"Under the conditions defined in Table 1 the PICC shall answer to a REQA with ATQA.
A PICC supporting the optional fc/64 bit rate shall operate under the conditions defined in Table 2 after
selection of a bit rate of fc/64. This PICC shall respond correctly to an I-block transmitted at a bit rate of fc/64.
A PICC supporting the optional fc/32 bit rate shall operate under the conditions defined in Table 3 after
selection of a bit rate of fc/32. The PICC shall respond correctly to an I-block transmitted at a bit rate of fc/32.
A PICC supporting the optional fc/16 bit rate shall operate under the conditions defined in Table 4 after
selection of a bit rate of fc/16. The PICC shall respond correctly to an I-block transmitted at a bit rate of fc/16."
Page 4, 7.2.2.2 of ISO/IEC 10373-6:2001/Amd.2:2003
Replace the existing text with the following:
"The test report shall confirm the intended operation at the mandatory fc/128 bit rate under the conditions
defined in Table 1. For PICCs supporting one or more of the optional high bit rates the test report shall confirm
the intended operation at the supported bit rates under the conditions defined in 7.2.2.1."
2 © ISO/IEC 2007 – All rights reserved

---------------------- Page: 5 ----------------------
ISO/IEC 10373-6:2001/Amd.5:2007(E)
Page 4, 7.2.3 of ISO/IEC 10373-6:2001/Amd.2:2003
Replace the existing text with the following:
"Tables 5 to 7 define additional test conditions to be applied for type B PICCs for different bit rates.
Page 4, 7.2.3 of ISO/IEC 10373-6:2001/Amd.2:2003
Replace the title of Table 2 (renumbered to Table 5) with the following: "Table 5 – Additional test condition
for bit rates of fc/128 and fc/64"
Page 4, 7.2.3 of ISO/IEC 10373-6:2001/Amd.2:2003
Insert the following table after Table 5:
Table 6 — Additional test conditions for a bit rate of fc/32
H m t , t
r f
Condition
(A/m) (%) (µs)
1 1,5 8 1
2 1,5 14 1
3 4,5 8 1
4 4,5 14 1
5 7,5 8 1
6 7,5 14 1

Page 4, 7.2.3 of ISO/IEC 10373-6:2001/Amd.2:2003
Insert the following table after Table 6:
Table 7 — Additional test conditions for a bit rate of fc/16
H m t , t
r f
Condition
(A/m) (%) (µs)
1 1,5 8 0,8
2 1,5 14 0,8
3 4,5 8 0,8
4 4,5 14 0,8
5 7,5 8 0,8
6 7,5 14 0,8

Page 5, 7.2.3.1 of ISO/IEC 10373-6:2001/Amd.2:2003
Replace the existing text with the following:
"Under the conditions defined in Table 5 the PICC operating at a bit rate of fc/128 shall answer to a REQB with
ATQB.
© ISO/IEC 2007 – All rights reserved 3

---------------------- Page: 6 ----------------------
ISO/IEC 10373-6:2001/Amd.5:2007(E)
A PICC supporting the optional fc/64 bit rate shall operate under the conditions defined in Table 5 after
selection of a bit rate of fc/64. This PICC shall respond correctly to an I-block transmitted at a bit rate of fc/64.
A PICC supporting the optional fc/32 bit rate shall operate under the conditions defined in Table 6 after
selection of a bit rate of fc/32. The PICC shall respond correctly to an I-block transmitted at a bit rate of fc/32.
A PICC supporting the optional fc/16 bit rate shall operate under the conditions defined in Table 7 after
selection of a bit rate of fc/16. The PICC shall respond correctly to an I-block transmitted at a bit rate of fc/16."
Page 5, 7.2.3.2 of ISO/IEC 10373-6:2001/Amd.2:2003
Replace the existing text with the following:
"The test report shall confirm the intended operation at the mandatory fc/128 bit rate under the conditions
defined in Table 5. For PICCs supporting one or more of the optional high bit rates the test report shall confirm
the intended operation at the supported bit rates under the conditions defined in 7.2.3.1."

Page 14, A.2
Insert new A.2.1 after the notes and before Figure A.3 with the following title and move the existing Figure A.3
into new A.2.1:
"A.2.1 Impedance matching network for a bit rate of fc/128"
Change the title of Figure A.3 to "Figure A.3 – Impedance matching network for a bit rate of fc/128"
Page 14, A.2
Insert new A.2.2 after new A.2.1 with the title "A.2.2 Impedance matching network for bit rates of fc/64,
fc/32 and fc/16" and insert the following figure into new A.2.2:


50 Ohm
Antenna coil
power driver
   Component Table:
impedance
matching
Value Unit Remarks
network
C1a 56 pF Voltage range 200V
C1b 5,6 pF Voltage range 200V
C1b
C2 180 pF Voltage range 200V
C3 15 pF Voltage range 200V
R
ext
C4 2-27 pF Voltage range 200V
Rext 2 Ohm Power range 8 W
C1a
R
ant
Z=50 Ohm C2 C3 C4
L
NOTE This impedance matching
ant
network is designed for tests up to 7,5 A/m.
Figure A.4 — Impedance matching network for bit rates of fc/64, fc/32 and fc/16
4 © ISO/IEC 2007 – All rights reserved

---------------------- Page: 7 ----------------------
ISO/IEC 10373-6:2001/Amd.5:2007(E)
Last page
Add the following new Annex J:
Annex J
(normative)
High bit rate selection test methods for PCD
J.1 Apparatus
In this test the PCD-test-apparatus shall be configurable to change the bit rate during the test procedure.
Tester shall be able to measure the bit rate used by the PCD on each stage of this test procedure.
J.2 Procedure
Place the PCD-test-apparatus into the field of the PCD.
J.2.1 Procedure for Type A
The following procedure shall be repeated for all values of interface byte TA(1) defined in Table J.1:
a) Run through activation sequence as defined in ISO/IEC 14443-3.
b) The PCD shall send a RATS command as defined in ISO/IEC 14443-4.
c) The PCD-test-apparatus answers with a valid ATS including TA(1) according to Table J.1.
d) The PCD may optionally send a PPS with a valid parameter setting for PPS1 byte according to Table J.1.
e) If the PCD has sent a PPS then the PCD-test-apparatus acknowledges the received PPS with a valid
PPS response.
f) The PCD shall send I(0) block using the bit rate selected.
0
NOTE This block may also be I(1) , or R(NACK) in case of PICC presence check method 2a.
0
g) The PCD-test-apparatus sends a valid response using the bit rate selected. Check, if the answer from the

PCD-test apparatus is accepted by the PCD.
Table J.1 — Correct behaviour of PCD after ATS with TA(1)
TA(1) Valid parameter setting for PPS1
a
(10000000)b (00000000)b
(10010001)b (00000101)b, (00000000)b
(10100010)b (00001010)b, (00000000)b
(10110011)b (00000101)b, (00001010)b, (00000000)b
(11000100)b (00001111)b, (00000000)b
(11010101)b (00000101)b, (00001111)b, (00000000)b
(11100110)b (00001010)b, (00001111)b, (00000000)b
© ISO/IEC 2007 – All rights reserved 5

---------------------- Page: 8 ----------------------
ISO/IEC 10373-6:2001/Amd.5:2007(E)
TA(1) Valid parameter setting for PPS1
(11110111)b (00000101)b, (00001010)b, (00001111)b, (00000000)b
a
(00000000)b (00000000)b
(00000001)b (00000001)b, (00000000)b
(00000010)b (00000010)b, (00000000)b
(00000011)b (00000001)b, (00000010)b, (00000000)b
(00000100)b (00000011)b, (00000000)b
(00000101)b (00000001)b, (00000011)b, (00000000)b
(00000110)b (00000010)b, (00000011)b, (00000000)b
(00000111)b (00000001)b, (00000010)b, (00000011)b, (00000000)b
(00000000)b
(00010000)b
(00000100)b
(00000001)b, (00000000)b
(00010001)b
(00000101)b, (00000100)b
(00000010)b, (00000000)b
(00010010)b
(00000110)b, (00000100)b
(00000001)b, (00000010)b, (00000000)b
(00010011)b
(00000101)b, (00000110)b, (00000100)b
(00000011)b, (00000000)b
(00010100)b
(00000111)b, (00000100)b
(00000001)b, (00000011)b, (00000000)b
(00010101)b
(00000101)b, (00000111)b, (00000100)b
(00000010)b, (00000011)b, (00000000)b
(00010110)b
(00000110)b, (00000111)b, (00000100)b
(00000001)b, (00000010)b, (00000011)b, (00000000)b
(00010111)b
(00000101)b, (00000110)b, (00000111)b, (00000100)b
(00000000)b
(00100000)b
(00001000)b
(00000001)b, (00000000)b
(00100001)b
(00001001)b, (00001000)b
(00000010)b, (00000000)b
(00100010)b
(00001010)b, (00001000)b
(00000001)b, (00000010)b, (00000000)b
(00100011)b
(00001001)b, (00001010)b, (00001000)b
(00000011)b, (00000000)b
(00100100)b
(00001011)b, (00001000)b
(00000001)b, (00000011)b, (00000000)b
(00100101)b
(00001001)b, (00001011)b, (00001000)b
(00000010)b, (00000011)b, (00000000)b
(00100110)b
(00001010)b, (00001011)b, (00001000)b
(00000001)b, (00000010)b, (00000011)b, (00000000)b
(00100111)b
(00001001)b, (00001010)b, (00001011)b, (00001000)b
(00000000)b
(00110000)b (00000100)b
(00001000)b
(00000001)b, (00000000)b
(00110001)b (00000101)b, (00000100)b
(00001001)b, (00001000)b
6 © ISO/IEC 2007 – All rights reserved

---------------------- Page: 9 --------------
...