ISO 17899:2004
(Main)Ships and marine technology — Marine electric window wipers
Ships and marine technology — Marine electric window wipers
ISO 17899:2004 specifies requirements for marine electric window wipers. It covers the required features, performance, constructional materials and electrical equipment for wiper systems for sea-going vessels where bridge duty is regularly maintained. It covers the performance, materials and electrical equipment for wipers required to meet the needs of ISO 8468 where such wipers are specified.
Navires et technologie marine — Essuie-glaces marins électriques
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 17899
First edition
2004-07-15
Ships and marine technology — Marine
electric window wipers
Navires et technologie marine — Essuie-glaces marins électriques
Reference number
ISO 17899:2004(E)
©
ISO 2004
---------------------- Page: 1 ----------------------
ISO 17899:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 17899:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Requirement. 1
5 Wiped area. 2
6 Design and construction. 2
7 Speeds. 2
8 Wipe quality. 3
9 Materials. 3
10 Electrical equipment. 3
11 Provision for de-icing . 3
12 Durability. 4
13 Salt mist test. 4
14 Temperature tests. 4
15 Salt water test. 4
16 Resistance to mechanical shock. 4
17 Vibration. 4
18 Compass safe distance. 4
19 Designation. 5
Bibliography . 6
© ISO 2004 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 17899:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17899 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee
SC 5, Ships' bridge layout.
iv © ISO 2004 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 17899:2004(E)
Introduction
A good standard of wiping needs to be ensured for ships' safety but there is currently no performance
standard for heavy-duty marine electric window wipers.
ISO 8468 calls for heavy-duty wipers to be fitted and applies to all sea-going ships where bridge duty is
regularly maintained. This International Standard specifies the requirements for heavy-duty wipers and goes
beyond the guidelines in 4.2.3 of ISO 8468 which are confined to the need for
an interval function,
fresh water wash,
capability to operate independently, and
a clear view in all operating conditions.
This International Standard includes criteria for wiper operating speeds, durability, ruggedness and
environmental compatibility for the complete wiper system. i.e. control system, motors, mechanisms and the
wiper blade itself.
ISO 3904 has been used as a guideline for this International Standard.
Equipment meeting these requirements is currently available commercially. This International Standard
provides important benchmarks against which independent classification societies can certify.
This International Standard embraces all the common wiper types used, i.e. straight line, pendulum and
pantograph, and includes wiper systems with drive motors mounted either inside or outside the ship's bridge.
© ISO 2004 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 17899:2004(E)
Ships and marine technology — Marine electric window wipers
1 Scope
This International Standard specifies requirements for marine electric window wipers. It covers the required
features, performance, constructional materials and electrical equipment for wiper systems for sea-going
vessels where bridge duty is regularly maintained. It covers the performance, materials and electrical
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.