ISO 10303-219:2007
(Main)Industrial automation systems and integration — Product data representation and exchange — Part 219: Application protocol: Dimensional inspection information exchange
Industrial automation systems and integration — Product data representation and exchange — Part 219: Application protocol: Dimensional inspection information exchange
ISO 10303-219:2007 establishes the entities and relationships necessary for the accommodation, preservation and exchange of dimensional inspection results, with their associated product data.
Systèmes d'automatisation industrielle et intégration — Représentation et échange de données de produits — Partie 219: Protocole d'application: Échange d'information par vérification dimensionnelle
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 10303-219
First edition
2007-12-15
Industrial automation systems and
integration — Product data
representation and exchange —
Part 219:
Application protocol: Dimensional
inspection information exchange
Systèmes d'automatisation industrielle et intégration — Représentation
et échange de données de produits —
Partie 219: Protocole d'application: Échange d'information par
vérification dimensionnelle
Reference number
©
ISO 2007
PDF disclaimer
PDF files may contain embedded typefaces. In accordance with Adobe's licensing policy, such files may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading a PDF file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create the PDF file(s) constituting this document can be found in the General Info relative to
the file(s); the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the files are suitable for
use by ISO member bodies. In the unlikely event that a problem relating to them is found, please inform the Central Secretariat at the
address given below.
This CD-ROM contains the publication ISO 10303-219:2007 in portable document format (PDF), which can
be viewed using Adobe® Acrobat® Reader.
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
© ISO 2007
All rights reserved. Unless required for installation or otherwise specified, no part of this CD-ROM may be reproduced, stored in a retrieval
system or transmitted in any form or by any means without prior permission from ISO. Requests for permission to reproduce this product
should be addressed to
I
...
INTERNATIONAL ISO
STANDARD 10303-219
First edition
2007-12-15
Industrial automation systems and
integration — Product data
representation and exchange —
Part 219:
Application protocol: Dimensional
inspection information exchange
Systèmes d'automatisation industrielle et intégration — Représentation
et échange de données de produits —
Partie 219: Protocole d'application: Échange d'information par
vérification dimensionnelle
Reference number
©
ISO 2007
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
Contents Page
1 Scope.1
2 Normative references .2
3 Terms, definitions and abbreviations.3
3.1 Terms defined in ISO 1101 .3
3.2 Terms defined in ISO 5459 .3
3.3 Terms defined in ISO 10303-1 .3
3.4 Terms defined in ISO 10303-42 .4
3.5 Other definitions.4
3.6 Abbreviations.4
4 Information requirements.5
4.1 Units of functionality.5
4.1.1 administrative_data .6
4.1.2 dimensional_measurement_analysis .6
4.1.3 dimensional_measurement_documentation .7
4.1.4 dimensional_measurement_execution .7
4.1.5 dimensional_measurement_features .8
4.1.6 dimensional_measurement_part.9
4.1.7 dimensional_measurement_parameters .9
4.1.8 feature_definition_items .9
4.1.9 feature_profile.11
4.1.10 manufacturing_feature .12
4.1.11 functional_limitations .15
4.1.12 part_properties .17
4.1.13 program_run.18
4.1.14 shape_representation_for_machining .18
4.2 Application objects.19
4.3 Application assertions.257
5 Application interpreted model .311
5.1 Mapping specification .311
5.1.1 administrative data UoF .312
5.1.2 dimensional_measurement_analysis UoF.318
5.1.3 dimensional_measurement_documentation UoF .330
5.1.4 dimensional_measurement_execution UoF .332
5.1.5 dimensional_measurement_features UoF .337
5.1.6 dimensional_measurement_part UoF.443
5.1.7 dimensional_measurement_parameters UoF .446
5.1.8 feature_definition_items UoF .455
5.1.9 feature_profile UoF.501
5.1.10 manufacturing_feature UoF .539
5.1.11 functional_limitations UoF .746
5.1.12 part properties UoF .797
5.1.13 program_run UoF.799
5.1.14 shape_representation_for_machining UoF .809
5.2 AIM EXPRESS short listing .828
5.2.1 Fundamental concepts and assumptions .832
5.2.2 Dimensional inspection schema types .832
5.2.3 Dimensional inspection schema entities .834
©ISO 2007 — All rights reserved iii
5.2.4 Dimensional inspection schema rules .940
6 Conformance requirements.959
Annex A (normative) AIM EXPRESS expanded listing .960
Annex B (normative) AIM short names .1191
Annex C (normative) Implementation method specific requirements.1204
Annex D (normative) Protocol Implementation Conformance Statement (PICS) proforma.1205
Annex E (normative) Information object registration.1206
Annex F (informative) Application activity model.1207
Annex G (informative) Application reference model .1234
Annex H (informative) AIM EXPRESS-G.1269
Annex I (informative) Computer interpretable listings.1299
Annex J (informative) Application protocol usage guide.1300
Bibliography .1525
Index .1526
Figures
Figure 1 — Data planning model.xii
Figure 2 — Angle_taper .22
Figure 3 — Angular_dimension_tolerance.23
Figure 4 — Angular_size_dimension_tolerance.25
Figure 5 — Angularity_tolerance for a plane surface.26
Figure 6 — Angularity_tolerance for an axis .26
Figure 7 — Bevel_gear.27
Figure 8 — Bevel_gear with shaft_angle and pitch_angle .28
Figure 9 — Bevel_gear with tip_angle and root_angle .28
Figure 10 — Block_base_shape .30
Figure 11 — Catalogue_gear .35
Figure 12 — Catalogue_knurl .36
Figure 13 — Catalogue_marking.37
Figure 14 — Catalogue_thread.37
Figure 15 — Chamfer .39
Figure 16 — Circular_boss.40
Figure 17 — Circular_boss with taper.41
Figure 18 — Circular_closed_profile .42
Figure 19 — Circular_offset_pattern.43
Figure 20 — Circular_omit_pattern.45
Figure 21 — Circular_pattern without rotation .46
Figure 22 — Circular_pattern with rotation of a base feature .46
Figure 23 — Circular_runout_tolerance.48
Figure 24 — Circularity_tolerance .49
Figure 25 — Complete_circular_path.50
Figure 26 — Compound_feature .51
Figure 27 — Concentricity_tolerance.53
Figure 28 — Conical_hole_bottom.54
Figure 29 — Constant_radius_edge_round .55
Figure 30 — Constant_radius_fillet.
...
INTERNATIONAL ISO
STANDARD 10303-219
First edition
2007-12-15
Industrial automation systems and
integration — Product data
representation and exchange —
Part 219:
Application protocol: Dimensional
inspection information exchange
Systèmes d'automatisation industrielle et intégration — Représentation
et échange de données de produits —
Partie 219: Protocole d'application: Échange d'information par
vérification dimensionnelle
Reference number
©
ISO 2007
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
Contents Page
1 Scope.1
2 Normative references .2
3 Terms, definitions and abbreviations.3
3.1 Terms defined in ISO 1101 .3
3.2 Terms defined in ISO 5459 .3
3.3 Terms defined in ISO 10303-1 .3
3.4 Terms defined in ISO 10303-42 .4
3.5 Other definitions.4
3.6 Abbreviations.4
4 Information requirements.5
4.1 Units of functionality.5
4.1.1 administrative_data .6
4.1.2 dimensional_measurement_analysis .6
4.1.3 dimensional_measurement_documentation .7
4.1.4 dimensional_measurement_execution .7
4.1.5 dimensional_measurement_features .8
4.1.6 dimensional_measurement_part.9
4.1.7 dimensional_measurement_parameters .9
4.1.8 feature_definition_items .9
4.1.9 feature_profile.11
4.1.10 manufacturing_feature .12
4.1.11 functional_limitations .15
4.1.12 part_properties .17
4.1.13 program_run.18
4.1.14 shape_representation_for_machining .18
4.2 Application objects.19
4.3 Application assertions.257
5 Application interpreted model .311
5.1 Mapping specification .311
5.1.1 administrative data UoF .312
5.1.2 dimensional_measurement_analysis UoF.318
5.1.3 dimensional_measurement_documentation UoF .330
5.1.4 dimensional_measurement_execution UoF .332
5.1.5 dimensional_measurement_features UoF .337
5.1.6 dimensional_measurement_part UoF.443
5.1.7 dimensional_measurement_parameters UoF .446
5.1.8 feature_definition_items UoF .455
5.1.9 feature_profile UoF.501
5.1.10 manufacturing_feature UoF .539
5.1.11 functional_limitations UoF .746
5.1.12 part properties UoF .797
5.1.13 program_run UoF.799
5.1.14 shape_representation_for_machining UoF .809
5.2 AIM EXPRESS short listing .828
5.2.1 Fundamental concepts and assumptions .832
5.2.2 Dimensional inspection schema types .832
5.2.3 Dimensional inspection schema entities .834
©ISO 2007 — All rights reserved iii
5.2.4 Dimensional inspection schema rules .940
6 Conformance requirements.959
Annex A (normative) AIM EXPRESS expanded listing .960
Annex B (normative) AIM short names .1191
Annex C (normative) Implementation method specific requirements.1204
Annex D (normative) Protocol Implementation Conformance Statement (PICS) proforma.1205
Annex E (normative) Information object registration.1206
Annex F (informative) Application activity model.1207
Annex G (informative) Application reference model .1234
Annex H (informative) AIM EXPRESS-G.1269
Annex I (informative) Computer interpretable listings.1299
Annex J (informative) Application protocol usage guide.1300
Bibliography .1525
Index .1526
Figures
Figure 1 — Data planning model.xii
Figure 2 — Angle_taper .22
Figure 3 — Angular_dimension_tolerance.23
Figure 4 — Angular_size_dimension_tolerance.25
Figure 5 — Angularity_tolerance for a plane surface.26
Figure 6 — Angularity_tolerance for an axis .26
Figure 7 — Bevel_gear.27
Figure 8 — Bevel_gear with shaft_angle and pitch_angle .28
Figure 9 — Bevel_gear with tip_angle and root_angle .28
Figure 10 — Block_base_shape .30
Figure 11 — Catalogue_gear .35
Figure 12 — Catalogue_knurl .36
Figure 13 — Catalogue_marking.37
Figure 14 — Catalogue_thread.37
Figure 15 — Chamfer .39
Figure 16 — Circular_boss.40
Figure 17 — Circular_boss with taper.41
Figure 18 — Circular_closed_profile .42
Figure 19 — Circular_offset_pattern.43
Figure 20 — Circular_omit_pattern.45
Figure 21 — Circular_pattern without rotation .46
Figure 22 — Circular_pattern with rotation of a base feature .46
Figure 23 — Circular_runout_tolerance.48
Figure 24 — Circularity_tolerance .49
Figure 25 — Complete_circular_path.50
Figure 26 — Compound_feature .51
Figure 27 — Concentricity_tolerance.53
Figure 28 — Conical_hole_bottom.54
Figure 29 — Constant_radius_edge_round .55
Figure 30 — Constant_radius_fillet.
...
INTERNATIONAL ISO
STANDARD 10303-219
First edition
2007-12-15
Industrial automation systems and
integration — Product data
representation and exchange —
Part 219:
Application protocol: Dimensional
inspection information exchange
Systèmes d'automatisation industrielle et intégration — Représentation
et échange de données de produits —
Partie 219: Protocole d'application: Échange d'information par
vérification dimensionnelle
Reference number
©
ISO 2007
PDF disclaimer
PDF files may contain embedded typefaces. In accordance with Adobe's licensing policy, such files may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading a PDF file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create the PDF file(s) constituting this document can be found in the General Info relative to
the file(s); the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the files are suitable for
use by ISO member bodies. In the unlikely event that a problem relating to them is found, please inform the Central Secretariat at the
address given below.
This CD-ROM contains the publication ISO 10303-219:2007 in portable document format (PDF), which can
be viewed using Adobe® Acrobat® Reader.
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
© ISO 2007
All rights reserved. Unless required for installation or otherwise specified, no part of this CD-ROM may be reproduced, stored in a retrieval
system or transmitted in any form or by any means without prior permission from ISO. Requests for permission to reproduce this product
should be addressed to
I
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.