Building construction — Jointing products — Specifications for test substrates

Construction immobilière — Matériaux pour joints — Prescriptions relatives aux supports d'essais

General Information

Status
Withdrawn
Publication Date
15-Dec-1999
Withdrawal Date
15-Dec-1999
Technical Committee
Drafting Committee
Current Stage
9599 - Withdrawal of International Standard
Completion Date
12-Jul-2018
Ref Project

Relations

Buy Standard

Standard
ISO 13640:1999 - Building construction -- Jointing products -- Specifications for test substrates
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 13640:1999 - Construction immobiliere -- Matériaux pour joints -- Prescriptions relatives aux supports d'essais
French language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 13640
First edition
1999-12-15
Building construction — Jointing
products — Specifications for test
substrates
Construction immobilière — Matériaux pour joints — Prescriptions relatives
aux supports d'essais
Reference number
ISO 13640:1999(E)
©
ISO 1999

---------------------- Page: 1 ----------------------
ISO 13640:1999(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 1999 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 13640:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 13640 was prepared by Technical Committee ISO/TC 59, Building construction,
Subcommittee SC 8, Jointing products.
© ISO 1999 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 13640:1999(E)
Building construction — Jointing products —
Specifications for test substrates
1 Scope
This International Standard specifies the procedures for producing substrates of mortar, glass and anodized
aluminium used for testing sealants.
The purpose of these requirements is to ensure the reproducibility of the standardized tests conducted on sealants
through the precise definition of both the composition and the method of preparation of the test substrates.
The substrates defined in this International Standard are indicators of the sealant's performance and not substrates
which reproduce the characteristics of the construction materials.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 209-1:1989, Wrought aluminium and aluminium alloys — Chemical composition and forms of products —
Part 1: Chemical composition.
ISO 2143:1981, Anodizing of aluminium and its alloys — Estimation of loss of absorptive power of anodic oxide
coatings after sealing — Dye spot test with prior acid treatment.
ISO 6707-1:1989, Building and civil engineering — Vocabulary — Part 1: General terms.
ISO 6927:1981, Building construction — Jointing products — Sealants —
...

NORME ISO
INTERNATIONALE 13640
Première édition
1999-12-15
Construction immobilière — Matériaux pour
joints — Prescriptions relatives aux
supports d'essais
Building construction — Jointing products — Specifications for test
substrates
Numéro de référence
ISO 13640:1999(F)
©
ISO 1999

---------------------- Page: 1 ----------------------
ISO 13640:1999(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait la
responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
© ISO 1999
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l’ISO à
l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
ImpriméenSuisse
ii © ISO 1999 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 13640:1999(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 3.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités
membres votants.
L’attention est appelée sur le fait que certains des éléments de la présente Norme internationale peuvent faire
l’objet de droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence.
La Norme internationale ISO 13640 a été élaborée par le comité technique ISO/TC 59, Construction immobilière,
sous-comité SC 8, Matériaux pour joints.
© ISO 1999 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 13640:1999(F)
Construction immobilière — Matériaux pour joints —
Prescriptions relatives aux supports d'essais
1 Domaine d'application
La présente Norme internationale prescrit des méthodes de réalisation des supports en mortier, verre ou aluminium
anodisé, utilisés pour des essais sur mastics.
Ces prescriptions ont pour objectif d'assurer la reproductibilité des essais normalisés sur les mastics, à travers la
définition précise de la composition et du mode de préparation des supports d'essai.
Les supports définis dans la présente Norme internationale sont des indicateurs de performance des mastics et
non des supports reproduisant les caractéristiques des matériaux du bâtiment.
2 Références normatives
Les documents normatifs suivants contiennent des dispositions qui, par suite de la référence qui y est faite,
constituent des dispositions valables pour la présente Norme internationale. Pour les références datées, les
amendements ultérieurs ou les révisions de ces publications ne s’appliquent pas. Toutefois, les parties prenantes
aux accords fondés sur la présente Norme internationale sont invitées à rechercher la possibilité d'appliquer les
éditions les plus récentes des documents normatifs indiqués ci-après. Pour les références non datées, la dernière
édition du document normatif en référence s’applique. Les membres de l'ISO et de la CEI possèdent le registre des
Normes internationales en vigueur.
ISO 209-1:1989, Aluminium et alliages d'aluminium corroyés� Composition chimique et formes des produits�
Partie 1: Composition chimique.
ISO 2143:1981, Anodisation de l'aluminium et de ses alliages� Appréciation de la perte du pouvoir absorbant des
couches d'oxydes anodiques après colmatage� Essai à la goutte de colorant avec action acide préalable.
ISO 6707-1:1989, Bâtiment et génie civil� Vocabulaire� Partie 1: Terme
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.