Thermal insulating products for building applications — Determination of length and width

ISO 29465:2008 specifies the equipment and procedures for determining the length and width of full‑size products. It is applicable to thermal insulating products.

Produits isolants thermiques destinés aux applications du bâtiment — Détermination de la longueur et de la largeur

General Information

Status
Withdrawn
Publication Date
28-Oct-2008
Current Stage
9599 - Withdrawal of International Standard
Completion Date
15-Aug-2022
Ref Project

Relations

Buy Standard

Standard
ISO 29465:2008 - Thermal insulating products for building applications -- Determination of length and width
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 29465
First edition
2008-11-01


Thermal insulating products for building
applications — Determination of length
and width
Produits isolants thermiques destinés aux applications du bâtiment —
Détermination de la longueur et de la largeur




Reference number
ISO 29465:2008(E)
©
ISO 2008

---------------------- Page: 1 ----------------------
ISO 29465:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2008 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 29465:2008(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Terms and definitions. 1
3 Principle. 1
4 Apparatus . 1
5 Test specimens . 1
6 Procedure . 2
7 Calculation and expression of results. 3
8 Accuracy of measurement. 3
9 Test report . 3

© ISO 2008 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 29465:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 29465 was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the
built environment, Subcommittee SC 1, Test and measurement methods.
iv © ISO 2008 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 29465:2008(E)
Introduction
This International Standard comprises the original EN 822:1994 prepared by Technical Committee
CEN/TC 88, Thermal insulating materials and products, which has been amended by ISO/TC 163/SC 1 with
reference to conditioning and testing conditions in tropical countries.
This International Standard is one of a series of documents specifying test methods, based on existing
European Standards, that are being adopted by ISO. This “package” of standards includes the following group
of interrelated documents.
International Standard Respective EN
standard
ISO 29465, Thermal insulating products for building applications — Determination of length EN 822
and width
ISO 29466, Thermal insulating products for building applications — Determination of EN 823
thickness
ISO 29467, Thermal insulating products for building applications — Determination of EN 824
squareness
ISO 29468, Thermal insulating products for building applications — Determination of flatness EN 825
ISO 29469, Thermal insulating products for building applications — Determination of EN 826
compression behaviour
ISO 29470, Thermal insulating products for building applications — Determination of the EN 1602
apparent density
ISO 29471, Thermal insulating products for building applications — Determination of EN 1603
dimensional stability under constant normal laboratory conditions (23°C/50 % relative
humidity)
ISO 29472, Thermal insulating products for building applications — Determination of EN 1604
dimensional stability under specified temperature and humidity conditions
ISO 29764, Thermal insulating produ
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.