ISO 15500-1:2000
(Main)Road vehicles — Compressed natural gas (CNG) fuel system components — Part 1: General requirements and definitions
Road vehicles — Compressed natural gas (CNG) fuel system components — Part 1: General requirements and definitions
Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 1: Exigences générales et définitions
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 15500-1
First edition
2000-03-01
Road vehicles — Compressed natural gas
(CNG) fuel system components —
Part 1:
General requirements and definitions
Véhicules routiers — Composants des systèmes de combustible gaz
naturel comprimé (GNC) —
Partie 1: Exigences générales et définitions
Reference number
ISO 15500-1:2000(E)
©
ISO 2000
---------------------- Page: 1 ----------------------
ISO 15500-1:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading
this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in
this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 15500-1:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 15500 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 15500-1 was prepared by Technical Committee ISO/TC 22, Road vehicles,
Subcommittee SC 25, Road vehicles using natural gas.
ISO 15500 consists of the following parts, under the general title Road vehicles — Compressed natural gas (CNG)
fuel system components:
� Part 1: General requirements and definitions
� Part 2: Performance and general test methods
� Part 3: Check valve
� Part 4: Manual valve
� Part 5: Manual cylindrical valve
� Part 6: Automatic valve
� Part 7: Gas injector
� Part 8: Pressure indicator
� Part 9: Pressure regulator
� Part 10: Gas-flow adjuster
� Part 11: Gas/air mixer
� Part 12: Pressure relief valve (PRV)
� Part 13: Pressure relief device (PRD)
� Part 14: Excess flow valve
� Part 15: Gas-tight housing and ventilation hose
© ISO 2000 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 15500-1:2000(E)
� Part 16: Rigid fuel line
� Part 17: Flexible fuel line
� Part 18: Filter
� Part 19: Fittings
iv © ISO 2000 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 15500-1:2000(E)
Road vehicles — Compressed natural gas (CNG) fuel system
components —
Part 1:
General requirements and definitions
1 Scope
This part of ISO 15500 specifies general requirements and definitions of compressed natural gas fuel system
components, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general
design principles, and specifies requirements for instructions and marking.
This part of ISO 15500 is applicable to vehicles using natural gas in accordance with ISO 15403 (mono-fuel, bi-fuel
or dual-fuel applications). It is not applicable to the following:
a) liquefied natural gas (LNG) fuel system components located upstream of, and including, the vaporizer;
b) fuel containers;
c) stationary gas engines;
d) container mounting hardware;
e) electronic fuel management;
f) refuelling receptacles.
NOTE 1 It is recognized that miscellaneous components not specifically covered herein can be examined to meet the
criteria of this part of ISO 15500 and tested according to the appropriate functional tests
NOTE 2 All references to pressure in this part of ISO 15500 are to be considered gauge pressures unless otherwise
specified.
NOTE 3 This part of ISO 15500 is based upon a service pressure for natural gas as fuel of 20 MPa (200 bar) settled at
15 °C. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example,
a 25 MPa (250 bar) service pressure system will require pressures to be multiplied by 1,25.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 3833:1977, Road vehicles — Types — Terms and definitions.
ISO 6722-1:1996, Road vehicles — Unscreened low-tension cables — Part 1: Test methods.
© ISO 2000 – All rights reserved 1
---------------------- Page: 5 ----------------------
ISO 15500-1:2000(E)
ISO 6722-2:1996, Road vehicles — Unscreened low-tension cables — Part 2: Requirements.
ISO 6722-3:1993, Road vehicles — Unscreened low-tension cables — Part 3: Conductor sizes and dimensions for
thick-wall insulated cables.
ISO 6722-4:1993, Road vehicles — Unscreened low-tension cables — Part 4: Conductor sizes and dimensions for
thin-wall insulated cables.
1)
ISO 15403:— , Natural gas — Designation of the quality of natural gas for use as a compressed fuel for vehicles.
1)
ISO 15500-2:— , Road vehicles — Compressed natural gas (CNG) fuel system components — Part 2:
Performance and general test methods.
1)
ISO 15500
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.