ISO/IEC 7816-5:2004
(Main)Identification cards — Integrated circuit cards — Part 5: Registration of application providers
Identification cards — Integrated circuit cards — Part 5: Registration of application providers
ISO/IEC 7816-4 defines how to use an application identifier to ascertain the presence of and/or perform the retrieval of an application in a card. ISO/IEC 7816-5:2004 shows how to grant the uniqueness of application identifiers through the international registration of a part of this identifier, and defines the registration procedure, the authorities in charge thereof, the availability of the register which links the registered parts of the identifiers and the relevant application providers.
Cartes d'identification — Cartes à circuit intégré — Partie 5: Enregistrement des fournisseurs d'application
Identifikacijski dokumenti – Kartice z integriranim vezjem – 5. del: Registracija ponudnikov aplikacije
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2005
Identifikacijski dokumenti – Kartice z integriranim vezjem – 5. del: Registracija
ponudnikov aplikacije
Identification cards -- Integrated circuit cards -- Part 5: Registration of application
providers
Cartes d'identification -- Cartes à circuit intégré -- Partie 5: Enregistrement des
fournisseurs d'application
Ta slovenski standard je istoveten z: ISO/IEC 7816-5:2004
ICS:
35.240.15 Identifikacijske kartice in Identification cards and
sorodne naprave related devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO/IEC
STANDARD 7816-5
Second edition
2004-12-01
Identification cards — Integrated circuit
cards —
Part 5:
Registration of application providers
Cartes d'identification — Cartes à circuit intégré —
Partie 5: Enregistrement des fournisseurs d'application
Reference number
©
ISO/IEC 2004
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO/IEC 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2004 – All rights reserved
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms. 1
3.1 Terms and definitions. 1
3.2 Abbreviated terms. 1
4 Registration of international identifiers. 2
4.1 Request and registration procedures. 2
4.2 Appeal process . 2
4.3 Responsibilities of applicants . 3
5 Sponsoring Authorities . 3
5.1 Eligibility to become a Sponsoring Authority.3
5.2 Responsibilities. 3
6 Registration Management Group (RMG) . 4
6.1 Constitution . 4
6.2 Responsibilities. 4
6.3 Voting procedures . 5
7 Registration Authority . 5
7.1 Appointment . 5
7.2 Resignation. 5
7.3 General reponsibilities . 5
7.4 Responsibilities to applicants requesting a RID . 6
8 The register of RIDs . 6
8.1 Publication and availability. 6
8.2 Contents. 6
Annex A (normative) Registration form for a registered application provider identifier
of category A . 7
A.1 To be completed by the requesting organization. 7
A.2 To be completed by national standards body. 7
A.3 To be completed by ISO/IEC 7816-5 registration authority . 7
Annex B (informative) National registration . 8
B.1 Introduction . 8
B.2 Operation of national numbering systems.8
B.3 Contact with the registration authority. 8
B.4 Role of registration management group. 8
© ISO/IEC 2004 – All rights reserved iii
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 7816-5 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 17, Cards and personal identification.
This second edition cancels and replaces the first edition (ISO/IEC 7816-5:1994) and incorporates the
Amendment ISO/IEC 7816-5:1994/Amd.1:1996). The technical content of Clauses 5 and 6 of the first edition
is now to be found in the second edition of ISO/IEC 7816-4, and Annex A has been technically revised.
ISO/IEC 7816 consists of the following parts, under the general title Identification cards — Integrated circuit
cards:
— Part 1: Cards with contacts: Physical characteristics
— Part 2: Cards with contacts: Dimensions and location of the contacts
— Part 3: Cards with contacts: Electrical interface and transmission protocols
— Part 4: Organization, security and commands for interchange
— Part 5: Registration of application providers
— Part 6: Interindustry data elements for interchange
— Part 7: Interindustry commands for Structured Card Query Language (SCQL)
— Part 8: Commands for security operations
— Part 9: Commands for card management
— Part 10: Cards with contacts: Electrical interface for synchronous cards
— Part 11: Personal verification through biometric methods
— Part 12: Cards with contacts: USB electrical interface and operating procedures
— Part 15: Cryptographic information application
iv © ISO/IEC 2004 – All rights reserved
INTERNATIONAL STANDARD ISO/IEC 7816-5:2004(E)
Identification cards — Integrated circuit cards —
Part 5:
Registration of application providers
1 Scope
This part of ISO/IEC 7816 specifies a registration procedure for application providers, and establishes the
authorities and procedures to ensure and optimize the reliability of this registration.
NOTE 1 ISO/IEC 7816-4 defines the structures of registered application provider identifiers (RIDs), and how to use
them. A registered application provider identifier (RID) consists of five bytes.
NOTE 2 In international RIDs (assigned by the international registration authority), the first quartet is set to 'A'.
NOTE 3 In national RIDs (assigned by a national Registration Authority), the first quartet is set to 'D' and a relevant
country code follows (see Annex B).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO/IEC 7816-4, Identification cards — Integrated circuit cards — Part 4: Organization, security and
commands for interchange
3 Terms, definitions and abbreviated terms
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions, given in ISO/IEC 7816-4, apply.
3.1.1
application provider
entity providing the components that make up an application in the card
3.1.2
registered application provider identifier
data element (five bytes) that uniquely identifies an application provider
3.2 Abbreviated terms
RID Registered application provider identifier
RMG Registration management group
© ISO/IEC 2004 – All rights reserved 1
4 Registration of international identifiers
4.1 Request and registration procedures
4.1.1 Procedure for requesting a RID
An application provider (including international organisations) shall apply to the standards body of its related
country (i.e. national standards body), or in the absence of a national standards body, to the secretariat of the
ISO technical body responsible for this part of ISO/IEC 7816 for the assignment of a RID.
The applicant shall use the form shown in Annex A. Registration forms are also available, on request, from the
Registration Authority, the secretariat of the Registration Management Group (RMG) and the secretariat of the
ISO technical body responsible for this part of ISO/IEC 7816.
The national standards body or the secretariat of the ISO technical body responsible for this part of
ISO/IEC 7816 then acts as the "Sponsoring Authority" (see Clause 5) with respect to the request.
4.1.2 Criteria for approval of a request for a RID
Requests for a RID shall meet all the following criteria:
a) the applicant shall be a corporate entity or its subsidiaries operating under a specific legislative regulation;
b) the applicant requesting a RID shall not already have an international RID (registration category 'A').
Exceptionally an applicant may apply for more than one RID, subject to decision by the RMG.
4.1.3 Criteria for rejection of a request for a RID
A request for a RID shall be rejected if any of the following conditions exist:
a) the applicant is not an application provider as defined by 3.1.1;
b) the applicant has requested a specific number or the reservation in the register of a specific number or has
made a request which is outside the scope of this part of ISO/IEC 7816.
NOTE Where special circumstances exist, the Sponsoring Authority may approve a request and forward the request
to the Registration Authority for assignment of a number. All such assignments must be reported by the Sponsoring
Authority to the RMG.
4.2 Appeal process
4.2.1 Appeal bodies
...
INTERNATIONAL ISO/IEC
STANDARD 7816-5
Second edition
2004-12-01
Identification cards — Integrated circuit
cards —
Part 5:
Registration of application providers
Cartes d'identification — Cartes à circuit intégré —
Partie 5: Enregistrement des fournisseurs d'application
Reference number
©
ISO/IEC 2004
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO/IEC 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2004 – All rights reserved
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms. 1
3.1 Terms and definitions. 1
3.2 Abbreviated terms. 1
4 Registration of international identifiers. 2
4.1 Request and registration procedures. 2
4.2 Appeal process . 2
4.3 Responsibilities of applicants . 3
5 Sponsoring Authorities . 3
5.1 Eligibility to become a Sponsoring Authority.3
5.2 Responsibilities. 3
6 Registration Management Group (RMG) . 4
6.1 Constitution . 4
6.2 Responsibilities. 4
6.3 Voting procedures . 5
7 Registration Authority . 5
7.1 Appointment . 5
7.2 Resignation. 5
7.3 General reponsibilities . 5
7.4 Responsibilities to applicants requesting a RID . 6
8 The register of RIDs . 6
8.1 Publication and availability. 6
8.2 Contents. 6
Annex A (normative) Registration form for a registered application provider identifier
of category A . 7
A.1 To be completed by the requesting organization. 7
A.2 To be completed by national standards body. 7
A.3 To be completed by ISO/IEC 7816-5 registration authority . 7
Annex B (informative) National registration . 8
B.1 Introduction . 8
B.2 Operation of national numbering systems.8
B.3 Contact with the registration authority. 8
B.4 Role of registration management group. 8
© ISO/IEC 2004 – All rights reserved iii
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 7816-5 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 17, Cards and personal identification.
This second edition cancels and replaces the first edition (ISO/IEC 7816-5:1994) and incorporates the
Amendment ISO/IEC 7816-5:1994/Amd.1:1996). The technical content of Clauses 5 and 6 of the first edition
is now to be found in the second edition of ISO/IEC 7816-4, and Annex A has been technically revised.
ISO/IEC 7816 consists of the following parts, under the general title Identification cards — Integrated circuit
cards:
— Part 1: Cards with contacts: Physical characteristics
— Part 2: Cards with contacts: Dimensions and location of the contacts
— Part 3: Cards with contacts: Electrical interface and transmission protocols
— Part 4: Organization, security and commands for interchange
— Part 5: Registration of application providers
— Part 6: Interindustry data elements for interchange
— Part 7: Interindustry commands for Structured Card Query Language (SCQL)
— Part 8: Commands for security operations
— Part 9: Commands for card management
— Part 10: Cards with contacts: Electrical interface for synchronous cards
— Part 11: Personal verification through biometric methods
— Part 12: Cards with contacts: USB electrical interface and operating procedures
— Part 15: Cryptographic information application
iv © ISO/IEC 2004 – All rights reserved
INTERNATIONAL STANDARD ISO/IEC 7816-5:2004(E)
Identification cards — Integrated circuit cards —
Part 5:
Registration of application providers
1 Scope
This part of ISO/IEC 7816 specifies a registration procedure for application providers, and establishes the
authorities and procedures to ensure and optimize the reliability of this registration.
NOTE 1 ISO/IEC 7816-4 defines the structures of registered application provider identifiers (RIDs), and how to use
them. A registered application provider identifier (RID) consists of five bytes.
NOTE 2 In international RIDs (assigned by the international registration authority), the first quartet is set to 'A'.
NOTE 3 In national RIDs (assigned by a national Registration Authority), the first quartet is set to 'D' and a relevant
country code follows (see Annex B).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO/IEC 7816-4, Identification cards — Integrated circuit cards — Part 4: Organization, security and
commands for interchange
3 Terms, definitions and abbreviated terms
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions, given in ISO/IEC 7816-4, apply.
3.1.1
application provider
entity providing the components that make up an application in the card
3.1.2
registered application provider identifier
data element (five bytes) that uniquely identifies an application provider
3.2 Abbreviated terms
RID Registered application provider identifier
RMG Registration management group
© ISO/IEC 2004 – All rights reserved 1
4 Registration of international identifiers
4.1 Request and registration procedures
4.1.1 Procedure for requesting a RID
An application provider (including international organisations) shall apply to the standards body of its related
country (i.e. national standards body), or in the absence of a national standards body, to the secretariat of the
ISO technical body responsible for this part of ISO/IEC 7816 for the assignment of a RID.
The applicant shall use the form shown in Annex A. Registration forms are also available, on request, from the
Registration Authority, the secretariat of the Registration Management Group (RMG) and the secretariat of the
ISO technical body responsible for this part of ISO/IEC 7816.
The national standards body or the secretariat of the ISO technical body responsible for this part of
ISO/IEC 7816 then acts as the "Sponsoring Authority" (see Clause 5) with respect to the request.
4.1.2 Criteria for approval of a request for a RID
Requests for a RID shall meet all the following criteria:
a) the applicant shall be a corporate entity or its subsidiaries operating under a specific legislative regulation;
b) the applicant requesting a RID shall not already have an international RID (registration category 'A').
Exceptionally an applicant may apply for more than one RID, subject to decision by the RMG.
4.1.3 Criteria for rejection of a request for a RID
A request for a RID shall be rejected if any of the following conditions exist:
a) the applicant is not an application provider as defined by 3.1.1;
b) the applicant has requested a specific number or the reservation in the register of a specific number or has
made a request which is outside the scope of this part of ISO/IEC 7816.
NOTE Where special circumstances exist, the Sponsoring Authority may approve a request and forward the request
to the Registration Authority for assignment of a number. All such assignments must be reported by the Sponsoring
Authority to the RMG.
4.2 Appeal process
4.2.1 Appeal bodies
Where a request has been rejected by a Sponsoring Authority, the applicant may appeal to the secretariat of
the RMG (see Clause 6). Where a request has been rejected by the RMG, the applicant may appeal to the
ISO technical body responsible for this part of ISO/IEC 7816 through the secretariat of that ISO technical body.
Applicants may submit for appeal requests that have been rejected by the ISO technical body responsible for
this part of ISO/IEC 7816 to the ISO Central Secretariat.
Appeal against rejection of a request shall be submitted to the appropriate body within 90 days of the date of
the letter of rejection.
2 © ISO/IEC 2004 – All rights reserved
4.2.2 Information to be provided
Where the Sponsoring Authority has rejected a request, the applicant shall provide the following information to
the relevant appeal body in support of the appeal:
a) Statement of which re
...
INTERNATIONAL ISO/IEC
STANDARD 7816-5
Second edition
2004-12-01
Identification cards — Integrated circuit
cards —
Part 5:
Registration of application providers
Cartes d'identification — Cartes à circuit intégré —
Partie 5: Enregistrement des fournisseurs d'application
Reference number
©
ISO/IEC 2004
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO/IEC 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2004 – All rights reserved
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms. 1
3.1 Terms and definitions. 1
3.2 Abbreviated terms. 1
4 Registration of international identifiers. 2
4.1 Request and registration procedures. 2
4.2 Appeal process . 2
4.3 Responsibilities of applicants . 3
5 Sponsoring Authorities . 3
5.1 Eligibility to become a Sponsoring Authority.3
5.2 Responsibilities. 3
6 Registration Management Group (RMG) . 4
6.1 Constitution . 4
6.2 Responsibilities. 4
6.3 Voting procedures . 5
7 Registration Authority . 5
7.1 Appointment . 5
7.2 Resignation. 5
7.3 General reponsibilities . 5
7.4 Responsibilities to applicants requesting a RID . 6
8 The register of RIDs . 6
8.1 Publication and availability. 6
8.2 Contents. 6
Annex A (normative) Registration form for a registered application provider identifier
of category A . 7
A.1 To be completed by the requesting organization. 7
A.2 To be completed by national standards body. 7
A.3 To be completed by ISO/IEC 7816-5 registration authority . 7
Annex B (informative) National registration . 8
B.1 Introduction . 8
B.2 Operation of national numbering systems.8
B.3 Contact with the registration authority. 8
B.4 Role of registration management group. 8
© ISO/IEC 2004 – All rights reserved iii
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 7816-5 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 17, Cards and personal identification.
This second edition cancels and replaces the first edition (ISO/IEC 7816-5:1994) and incorporates the
Amendment ISO/IEC 7816-5:1994/Amd.1:1996). The technical content of Clauses 5 and 6 of the first edition
is now to be found in the second edition of ISO/IEC 7816-4, and Annex A has been technically revised.
ISO/IEC 7816 consists of the following parts, under the general title Identification cards — Integrated circuit
cards:
— Part 1: Cards with contacts: Physical characteristics
— Part 2: Cards with contacts: Dimensions and location of the contacts
— Part 3: Cards with contacts: Electrical interface and transmission protocols
— Part 4: Organization, security and commands for interchange
— Part 5: Registration of application providers
— Part 6: Interindustry data elements for interchange
— Part 7: Interindustry commands for Structured Card Query Language (SCQL)
— Part 8: Commands for security operations
— Part 9: Commands for card management
— Part 10: Cards with contacts: Electrical interface for synchronous cards
— Part 11: Personal verification through biometric methods
— Part 12: Cards with contacts: USB electrical interface and operating procedures
— Part 15: Cryptographic information application
iv © ISO/IEC 2004 – All rights reserved
INTERNATIONAL STANDARD ISO/IEC 7816-5:2004(E)
Identification cards — Integrated circuit cards —
Part 5:
Registration of application providers
1 Scope
This part of ISO/IEC 7816 specifies a registration procedure for application providers, and establishes the
authorities and procedures to ensure and optimize the reliability of this registration.
NOTE 1 ISO/IEC 7816-4 defines the structures of registered application provider identifiers (RIDs), and how to use
them. A registered application provider identifier (RID) consists of five bytes.
NOTE 2 In international RIDs (assigned by the international registration authority), the first quartet is set to 'A'.
NOTE 3 In national RIDs (assigned by a national Registration Authority), the first quartet is set to 'D' and a relevant
country code follows (see Annex B).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO/IEC 7816-4, Identification cards — Integrated circuit cards — Part 4: Organization, security and
commands for interchange
3 Terms, definitions and abbreviated terms
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions, given in ISO/IEC 7816-4, apply.
3.1.1
application provider
entity providing the components that make up an application in the card
3.1.2
registered application provider identifier
data element (five bytes) that uniquely identifies an application provider
3.2 Abbreviated terms
RID Registered application provider identifier
RMG Registration management group
© ISO/IEC 2004 – All rights reserved 1
4 Registration of international identifiers
4.1 Request and registration procedures
4.1.1 Procedure for requesting a RID
An application provider (including international organisations) shall apply to the standards body of its related
country (i.e. national standards body), or in the absence of a national standards body, to the secretariat of the
ISO technical body responsible for this part of ISO/IEC 7816 for the assignment of a RID.
The applicant shall use the form shown in Annex A. Registration forms are also available, on request, from the
Registration Authority, the secretariat of the Registration Management Group (RMG) and the secretariat of the
ISO technical body responsible for this part of ISO/IEC 7816.
The national standards body or the secretariat of the ISO technical body responsible for this part of
ISO/IEC 7816 then acts as the "Sponsoring Authority" (see Clause 5) with respect to the request.
4.1.2 Criteria for approval of a request for a RID
Requests for a RID shall meet all the following criteria:
a) the applicant shall be a corporate entity or its subsidiaries operating under a specific legislative regulation;
b) the applicant requesting a RID shall not already have an international RID (registration category 'A').
Exceptionally an applicant may apply for more than one RID, subject to decision by the RMG.
4.1.3 Criteria for rejection of a request for a RID
A request for a RID shall be rejected if any of the following conditions exist:
a) the applicant is not an application provider as defined by 3.1.1;
b) the applicant has requested a specific number or the reservation in the register of a specific number or has
made a request which is outside the scope of this part of ISO/IEC 7816.
NOTE Where special circumstances exist, the Sponsoring Authority may approve a request and forward the request
to the Registration Authority for assignment of a number. All such assignments must be reported by the Sponsoring
Authority to the RMG.
4.2 Appeal process
4.2.1 Appeal bodies
Where a request has been rejected by a Sponsoring Authority, the applicant may appeal to the secretariat of
the RMG (see Clause 6). Where a request has been rejected by the RMG, the applicant may appeal to the
ISO technical body responsible for this part of ISO/IEC 7816 through the secretariat of that ISO technical body.
Applicants may submit for appeal requests that have been rejected by the ISO technical body responsible for
this part of ISO/IEC 7816 to the ISO Central Secretariat.
Appeal against rejection of a request shall be submitted to the appropriate body within 90 days of the date of
the letter of rejection.
2 © ISO/IEC 2004 – All rights reserved
4.2.2 Information to be provided
Where the Sponsoring Authority has rejected a request, the applicant shall provide the following information to
the relevant appeal body in support of the appeal:
a) Statement of which re
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.