ISO/DIS 8178-2
(Main)Reciprocating internal combustion engines -- Exhaust emission measurement
Reciprocating internal combustion engines -- Exhaust emission measurement
Moteurs alternatifs à combustion interne -- Mesurage des émissions de gaz d'échappement
General Information
RELATIONS
Standards Content (sample)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8178-2
ISO/TC 70/SC 8 Secretariat: DIN
Voting begins on: Voting terminates on:
2021-02-17 2021-05-12
Reciprocating internal combustion engines — Exhaust
emission measurement —
Part 2:
Measurement of gaseous and particulate exhaust
emissions under field conditions
Moteurs alternatifs à combustion interne — Mesurage des émissions de gaz d'échappement —
Partie 2: Mesurage des émissions de gaz et de particules sur siteICS: 13.040.50; 27.020
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
This document is circulated as received from the committee secretariat.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8178-2:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021
---------------------- Page: 1 ----------------------
ISO/DIS 8178-2:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DIS 8178-2:2021(E)
Contents Page
Foreword ..........................................................................................................................................................................................................................................v
Introduction ................................................................................................................................................................................................................................vi
1 Scope ................................................................................................................................................................................................................................. 1
2 Normative references ...................................................................................................................................................................................... 1
3 Terms and definitions ..................................................................................................................................................................................... 2
4 Symbols and abbreviations ....................................................................................................................................................................... 3
4.1 Symbols ......................................................................................................................................................................................................... 3
4.2 Measured chemical components ............................................................................................................................................. 3
4.3 Abbreviations ........................................................................................................................................................................................... 4
5 Discrete-mode steady-state tests in the field when it is intended to either conduct
measurements at a single operating point or conduct a weighted cycle-based test ......................4
5.1 General ........................................................................................................................................................................................................... 4
5.2 Test conditions ........................................................................................................................................................................................ 4
5.2.1 General requirements .................................................................................................................................................. 4
5.2.2 Engine test conditions ................................................................................................................................................. 5
5.2.3 Power ......................................................................................................................................................................................... 5
5.2.4 Engine air intake system ........................................................................................................................................... 5
5.2.5 Charge air cooler .............................................................................................................................................................. 6
5.2.6 Engine exhaust system ............................................................................................................................................... 6
5.2.7 Engines with exhaust after-treatment systems .................. ................................................................... 6
5.2.8 Crankcase emissions..................................................................................................................................................... 6
5.2.9 Cooling system ................................................................................................................................................................... 6
5.2.10 Lubricating oil .................................................................................................................................................................... 6
5.2.11 Test fuels ................................................................................................................................................................................. 6
5.3 Installation of sampling probes and equipment ........................................................................................................ 7
5.4 Measurement equipment and data to be measured ............................................................................................... 7
5.4.1 General...................................................................................................................................................................................... 7
5.4.2 Torque and speed ............................................................................................................................................................ 8
5.4.3 Exhaust gas flow ............................................................................................................................................................... 9
5.4.4 Accuracy of the data to be measured ............................................................................................................. 9
5.4.5 Determination of the gaseous components .............................................................................................. 9
5.4.6 Determination of the particulates ..................................................................................................................... 9
5.5 Running conditions ..........................................................................................................................................................................10
5.5.1 Test cycles ...........................................................................................................................................................................10
5.5.2 Preparation of the engine ......................................................................................................................................10
5.6 Test run .......................................................................................................................................................................................................10
5.6.1 PM measurement..........................................................................................................................................................10
5.6.2 Dilution air for particulate measurement ...............................................................................................11
5.6.3 Test sequence .................. .................................................... .............................................................................................11
5.6.4 Gas analyser drift validation and correction ........................................................................................11
5.6.5 Emissions evaluation and calculation ........................................................................................................11
5.6.6 Test report ..........................................................................................................................................................................11
6 Measurement of gaseous emissions performance of engines during typical in-service operation under field conditions using portable emission measurement
systems (PEMS) ...................................................................................................................................................................................................12
6.1 Test conditions .....................................................................................................................................................................................12
6.1.1 General requirements ...............................................................................................................................................12
6.1.2 Selection of engine for assessment of design performance .....................................................12
6.1.3 Machinery operation .................................................................................................................................................12
6.1.4 Ambient conditions ....................................................................................................................................................13
6.1.5 Lubricating oil, fuel and reagent .....................................................................................................................13
6.1.6 Operating sequence ....................................................................................................................................................13
© ISO 2021 – All rights reserved iii---------------------- Page: 3 ----------------------
ISO/DIS 8178-2:2021(E)
6.2 Data sampling methods ................................................................................................................................................................14
6.2.1 Continuous data sampling ....................................................................................................................................14
6.2.2 Combined data sampling .......................................................................................................................................14
6.2.3 Temporary signal loss...............................................................................................................................................15
6.3 ECU data stream ......... .........................................................................................................................................................................15
6.3.1 Verification of availability and conformity of information .......................................................15
6.4 Test procedures ...................................................................................................................................................................................15
6.5 Data pre-processing .........................................................................................................................................................................15
6.6 Determination of working events ........................................................................................................................................15
6.6.1 Combining operating sequences .....................................................................................................................15
6.7 Test data availability .......................................................................................................................................................................15
6.8 Calculations .............................................................................................................................................................................................16
6.8.1 Engines without communication interface ............................................................................................16
6.9 Test report ................................................................................................................................................................................................16
6.10 Instantaneous measured data file and instantaneous calculated data file ......................................16
6.11 Overview of measurement and evaluation sequence .........................................................................................16
Annex A (normative) Portable Emissions Measurement System (PEMS) ...................................................................18
Annex B (normative) Test procedure for gaseous emission measurement with a PEMS ...........................20
Annex C (normative) Determination of reference work and CO for engines for which the
applicable bench test cycle is solely NRSC ..............................................................................................................................28
Annex D (normative) Data pre-processing for gaseous pollutant emissions calculations .......................30
Annex E (normative) Algorithm for the determination of working events during in-service
testing ...........................................................................................................................................................................................................................35
Annex F (normative) Determination of the instantaneous proxy power from CO mass flow rate .39
Annex G (normative) Gaseous pollutant emissions calculations.........................................................................................41
Annex H (normative) Conformity of the ECU torque signal .......................................................................................................48
Annex I (normative) ECU data stream information requirements ....................................................................................49
Annex J (informative) Test report for in-service testing ...............................................................................................................51
Annex K (normative) Performance specifications, calibration and response factor for
Zirconium Dioxide (ZRDO) NOx analyser ................................................................................................................................57
Bibliography .............................................................................................................................................................................................................................59
iv © ISO 2021 – All rights reserved---------------------- Page: 4 ----------------------
ISO/DIS 8178-2:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 70, Internal combustion engines,
Subcommittee SC 8, Exhaust gas emission measurement.This third edition cancels and replaces the second edition (ISO 8178-2:2008), which has been technically
revised.The main changes compared to the previous edition are as follows:
— updated to reflect the section applicable for discrete-mode steady-state tests in the field when it is
intended to either conduct measurements at a single operating point or conduct a weighted cycle-
based test, reflecting advances in the latest versions of the other parts of the ISO 8178 series
— Expansion of the section on measurement of gaseous emissions performance of engines during
typical in-service operation under field conditions using portable emission measurement systems
(PEMS), including detailed requirements for performing moving average window data evaluation
— corresponding extensive restructure of the layout of this documentA list of all parts in the ISO 8178 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.© ISO 2021 – All rights reserved v
---------------------- Page: 5 ----------------------
ISO/DIS 8178-2:2021(E)
Introduction
Evaluating emissions from non-road engines is more complicated than the same task for on-road
engines due to the diversity of non-road applications. For example, on-road applications primarily
consist of moving a load from one point to another on a paved roadway. The constraints of the paved
roadways, maximum acceptable pavement loads and maximum allowable grades of fuel, narrow the
scope of on-road vehicle and engine sizes.Non-road engines and vehicles include a wider range of size, including size of the engines that power
the equipment. Many of the engines are large enough to preclude the application of test equipment
and methods that were acceptable for on-road purposes. In cases where a laboratory test using a
dynamometer is not possible, testing at site or under appropriate conditions can be a viable alternative.
Where it is not possible to use a test bed or where information is required on the actual emissions
produced by an in-service engine, the site test procedures and calculation methods specified in
ISO 8178-2 are appropriate. This part should only be used with the agreement of the parties involved.
It should be recognized that data obtained under these circumstances may not agree completely with
previous or future data, obtained in a laboratory or in the field, due to the variability and uncontrolled
nature of testing in the field.vi © ISO 2021 – All rights reserved
---------------------- Page: 6 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 8178-2:2021(E)
Reciprocating internal combustion engines — Exhaust
emission measurement —
Part 2:
Measurement of gaseous and particulate exhaust
emissions under field conditions
1 Scope
This document, together with ISO 8178-1:2020 and ISO 8178-4:2020, specifies the measurement
and evaluation methods for gaseous and particulate exhaust emissions from reciprocating internal
combustion engines (RIC engines) in the field.This document is applied when the emissions from RIC engines used in non-road machinery, industrial
equipment, marine installations, generating sets, diesel rail traction or similar machinery applications
need to be measured in the field. Clause 5 applies for the conduct of discrete-mode steady-state gaseous
or particulate emission measurements at a single operating point or conduct a weighted cycle-based test
in the field. Clause 6 applies where it is necessary to assess gaseous emissions performance of engines
during typical in-service operation under field conditions using portable emission measurement
systems (PEMS).2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 8178-1, Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test-
bed measurement systems of gaseous and particulate emissionsISO 8178-4, Reciprocating internal combustion engines — Exhaust emission measurement — Part 4:
Steady-state and transient test cycles for different engine applicationsISO 8178-5, Reciprocating internal combustion engines — Exhaust emission measurement — Part 5:
Test fuelsISO 8178-6, Reciprocating internal combustion engines — Exhaust emission measurement — Part 6:
Report of measuring results and testISO 14396, Reciprocating internal combustion engines — Determination and method for the measurement
of engine power — Additional requirements for exhaust emission tests in accordance with ISO 8178
ISO 17025, General requirements for the competence of testing and calibration laboratories
ISO 27145, Road vehicles — Implementation of World-Wide Harmonized On-Board Diagnostics (WWH-
OBD) communication requirementsISO 15765-4, Road vehicles. Diagnostic communication over Controller Area Network (DoCAN).
Requirements for emissions-related systemsISO 13400, Road vehicles — Diagnostic communication over Internet Protocol (DoIP)
ISO 15031-3, Road vehicles — Communication between vehicle and external equipment for emissions-
related diagnostics — Part 3: Diagnostic connector and related electrical circuits: Specification and use
© ISO 2021 – All rights reserved 1---------------------- Page: 7 ----------------------
ISO/DIS 8178-2:2021(E)
J1939-73, Application layer – diagnostics
ASTM E 29-06b, Standard Practice for Using Significant Digits in Test Data to Determine Conformance
with Specifications3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8178-1, ISO 8178-4 and the
following apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp— IEC Electropedia: available at http:// www .electropedia .org/
3.1
event
data measured in an in-service test for the gaseous pollutant emissions calculations obtained in a time
increment Δt equal to the data sampling period3.2
field conditions
conditions under which the engine under test is installed in, and coupled with, the actual equipment or
vehicle, which is driven by the engine, and conditions under which the equipment or vehicle is allowed
to function in normal use3.3
moving average window
period, measured in cumulative amount of work or CO , over which each integration of gaseous
pollutant emissions is performed3.4
operating sequence
elapsed time of uninterrupted machinery operation and continuous data sampling during an in-
service test3.5
portable emission measurement system
PEMS
emission measurement system that is transportable and suitable for conducting in-service
measurements3.6
proxy power
value obtained by simple linear interpolation based on certain assumptions for the sole purpose of
identifying non-working events when there is no torque signal from an ECU3.7
reference mass of CO
amount of cumulative CO measured during a prior bench-test of the engine type or, where applicable,
engine family, which is used to determine the size of the moving average CO window
3.8reference work
amount of cumulative work measured during a prior bench-test of the engine type or, where applicable,
engine family, which is used to determine the size of the moving average work window
2 © ISO 2021 – All rights reserved---------------------- Page: 8 ----------------------
ISO/DIS 8178-2:2021(E)
4 Symbols and abbreviations
4.1 Symbols
Table 1 — Symbols
Symbol Term Unit
D Maximum averaging window duration s
max
e Brake specific gaseous pollutant emissions g/kWh
gas
f Laboratory atmospheric factor —
f Conformity factor —
f Certification ratio —
CFC
f In-service ratio —
CFI
f Weighting factor —
K Simplified engine-family-specific CO constant —
veline 2
L Limit value g/kWh
m Mass emission of gaseous pollutant g
m Mass of CO for the test cycle g
CO2 2
m Reference mass of CO g
CO2ref 2
N Number of mode in test cycle —
mode
p Total barometric pressure kPa
p Dry atmospheric pressure kPa
P Uncorrected brake power kW
Declared total power absorbed by auxiliaries fitted for the test and not required by Annex B
P kWaux
of ISO 8178-4:2020
P Maximum measured or declared power kW
max
P Instantaneous proxy power kW
proxy,i
P Measured power kW
q Mean CO mass flow rate g/h
mCO2 2
r NO response factor of zirconium dioxide analyser —
NOx x
r NO response factor of zirconium dioxide analyser —
NO2 2
r Maximum NO /NO concentration ratio —
NO2,max 2 x
t Time s
t Reference time s
ref
T Temperature °C
Ta Absolute temperature K
W Work kWh
W Actual work kWh
act
W Reference work kWh
ref
4.2 Measured chemical components
The symbols for the measured chemical components are generally identical with those used in
ISO 8178-1 and ISO 8178-4. Those used in this document are given in Table 2 in order to facilitate
comprehension.© ISO 2021 – All rights reserved 3
---------------------- Page: 9 ----------------------
ISO/DIS 8178-2:2021(E)
Table 2 — Measured chemical components
Symbol Component
CO Carbon monoxide
CO Carbon dioxide
HC Hydrocarbons
NH Ammonia
NMHC Non-methane hydrocarbons
NO Nitrogen Dioxide
NO Oxides of nitrogen
PM Particulate matter
PN Particulate number
THC Total hydrocarbons
4.3 Abbreviations
Table 3 — Abbreviations
ECU Electronic Control Unit
EFM Exhaust Flow Meter
LSI-NRTC Large Spark-Ignition Non-Road Transient Cycle
NRMM Non-Road Mobile Machinery
NRSC Non-Road Steady-State Cycle
NRTC Non-Road Transient Cycle
RMC NRSC Ramped Modal Non-Road Steady-State Cycle
ZRDO Zirconium dioxide (analyser)
PEMS Portable Emissions Measurement System
5 Discrete-mode steady-state tests in the field when it is intended to either
conduct measurements at a single operating point or conduct a weighted cycle-
based test
5.1 General
Testing conducted according to clause 5 shall in general follow the requirements set out in
ISO 8178-1:2020 and -4 for discrete-mode steady-state testing. Deviations from the requirements of
those parts are limited to those set-out in clause 5. This clause shall not be used for transient testing.
5.2 Test conditions5.2.1 General requirements
Field measurements according to clause 5 shall be conducted only when test-bed measurement is not
appropriate because the required measurement cannot be performed on the test-bed.
Note When testing under field conditions the test cycles specified in ISO 8178-4:2020 might not be fully
reproduceable, there might be differences in engine operating parameters from laboratory conditions and there
might be differences in the accuracy of emission measurement equipment. Consequently, it is not expected
that the emission results obtained when testing according to clause 5 will be directly comparable to the values
obtained on the test bed.4 © ISO 2021 – All rights reserved
---------------------- Page: 10 ----------------------
ISO/DIS 8178-2:2021(E)
5.2.2 Engine test conditions
5.2.2.1 Ambient conditions
The temperature of the engine intake air, expressed in °C and the dry atmospheric pressure, p ,
expressed in kilopascal (kPa), shall be measured and recorded, and the parameter, f , sh
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.