Aerospace — Ball-ends, in corrosion-resistant steel, swaged on aircraft control wire rope — Dimensions and loads

This International Standard specifies the characteristics of ball-ends in corrosion-resistant steel swaged on aircraft control wire rope.

Aéronautique et espace — Embouts à sphère terminale, en acier résistant à la corrosion, à sertir sur câbles de commande d'aéronefs — Dimensions et charges

La présente Norme internationale spécifie les caractéristiques des embouts à sphère terminale, en acier résistant à la corrosion, à sertir sur câbles de commande d'aéronefs.

General Information

Status
Published
Publication Date
20-Dec-2000
Current Stage
9060 - Close of review
Start Date
04-Jun-2029
Ref Project

Buy Standard

Standard
ISO 9748:2000 - Aerospace -- Ball-ends, in corrosion-resistant steel, swaged on aircraft control wire rope -- Dimensions and loads
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 9748:2000 - Aéronautique et espace -- Embouts a sphere terminale, en acier résistant a la corrosion, a sertir sur câbles de commande d'aéronefs -- Dimensions et charges
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 9748
First edition
2000-12-15
Aerospace — Ball-ends, in corrosion-
resistant steel, swaged on aircraft control
wire rope — Dimensions and loads
Aéronautique et espace — Embouts à sphère terminale, en acier résistant à
la corrosion, à sertir sur câbles de commande d'aéronefs — Dimensions et
charges
A
Reference number
ISO 9748:2000(E)

---------------------- Page: 1 ----------------------
ISO 9748:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading
this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in
this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©  ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii

---------------------- Page: 2 ----------------------
© ISO
ISO 9748:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 9748 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles,
Subcommittee SC 12, Mechanical system parts.
Annex A forms a normative part of this International Standard.
iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD  © ISO ISO 9748:2000(E)
Aerospace — Ball-ends, in corrosion-resistant steel, swaged on
aircraft control wire rope — Dimensions and loads
1 Scope
This International Standard specifies the characteristics of ball-ends in corrosion-resistant steel swaged on aircraft
control wire rope.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this
International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do
not apply. However, parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated references,
the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of
currently valid International Standards.
ISO 2020-1:1997, Aerospace — Preformed flexible steel wire rope for aircraft controls — Part 1: Dimensions and
loads.
ISO 8074:1985, Aerospace — Surface treatment of austenitic stainless steel parts.
ISO 10955:1999, Aerospace — End fittings and turnbarrels for aircraft control wire rope — Technical specification.
ISO 13715:2000, Technical drawings — Edges of undefined shape — Vocabulary and indication on drawings.
1) 2)
EN 2465:— , Aerospace series — Steel FE-PA11 — Softened — Bars D ¶ 100 mm .
e
SAE AMS 2431/6A, Peening Media, Glass Shot.
SAE AMS 5639G, Steel, Corrosion Resistant, Bars, Wire, Forgings, Tubing, and Rings, 19Cr 10Ni, Solution Heat
Treated.
SAE AMS 5641F, Steel, Corrosion Resistant, Bars, Wire, and Forgings, 18.5Cr 10Ni 0.22Se Free-Machining;
Swaging or Upsetting, Solution Heat Treated.
3 Configuration, dimensions, loads and masses
Configuration, dime
...

NORME ISO
INTERNATIONALE 9748
Première édition
2000-12-15
Aéronautique et espace — Embouts à
sphère terminale, en acier résistant à la
corrosion, à sertir sur câbles de commande
d'aéronefs — Dimensions et charges
Aerospace — Ball-ends, in corrosion-resistant steel, swaged on aircraft
control wire rope — Dimensions and loads
A
Numéro de référence
ISO 9748:2000(F)

---------------------- Page: 1 ----------------------
ISO 9748:2000(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait
la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
©  ISO 2000
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l’ISO à
l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Imprimé en Suisse
ii

---------------------- Page: 2 ----------------------
© ISO
ISO 9748:2000(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée aux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 3.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités
membres votants.
La Norme internationale ISO 9748 a été élaborée par le comité technique ISO/TC 20, Aéronautique et espace,
sous-comité SC 12, Éléments de systèmes mécaniques.
L'annexe A constitue un élément normatif de la présente Norme internationale.
iii

---------------------- Page: 3 ----------------------
NORME INTERNATIONALE  © ISO ISO 9748:2000(F)
Aéronautique et espace — Embouts à sphère terminale, en acier
résistant à la corrosion, à sertir sur câbles de commande
d'aéronefs — Dimensions et charges
1 Domaine d’application
La présente Norme internationale spécifie les caractéristiques des embouts à sphère terminale, en acier résistant à
la corrosion, à sertir sur câbles de commande d'aéronefs.
2 Références normatives
Les documents normatifs suivants contiennent des dispositions qui, par suite de la référence qui y est faite,
constituent des dispositions valables pour la présente Norme internationale. Pour les références datées, les
amendements ultérieurs ou les révisions de ces publications ne s'appliquent pas. Toutefois, les parties prenantes
aux accords fondés sur la présente Norme internationale sont invitées à rechercher la possibilité d'appliquer les
éditions les plus récentes des documents normatifs indiqués ci-après. Pour les références non datées, la dernière
édition du document normatif en référence s'applique. Les membres de l'ISO et de la CEI possèdent le registre des
Normes internationales en vigueur.
ISO 2020-1:1997, Aéronautique et espace — Câbles en acier souples préformés pour commandes d'aéronefs —
Partie 1: Dimensions et charges.
ISO 8074:1985, Aéronautique et espace — Traitement de surface des éléments en acier inoxydable austénitique.
ISO 10955:1999, Aéronautique et espace — Embouts et tendeurs de câbles de commande d'aéronefs —
Spécifications techniques.
ISO 13
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.