ISO 29803:2010
(Main)Thermal insulation products for building applications — Determination of the resistance to impact of external thermal insulation composite systems (ETICS)
Thermal insulation products for building applications — Determination of the resistance to impact of external thermal insulation composite systems (ETICS)
ISO 29803:2010 specifies equipment and a procedure for determining the resistance to impact of external thermal insulation composite systems (ETICS).
Produits isolants thermiques destinés aux applications du bâtiment — Détermination de la résistance au choc des systèmes d'isolation thermique par l'extérieur (systèmes ITE)
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 29803
First edition
2010-01-15
Thermal insulation products for building
applications — Determination of the
resistance to impact of external thermal
insulation composite systems (ETICS)
Produits isolants thermiques destinés aux applications du bâtiment —
Détermination de la résistance au choc des systèmes d'isolation
thermique par l'extérieur (systèmes ITE)
Reference number
ISO 29803:2010(E)
©
ISO 2010
---------------------- Page: 1 ----------------------
ISO 29803:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 29803:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 29803 was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the
built environment, Subcommittee SC 1, Test and measurement methods.
ISO 29803 is based on EN 13497:2002 prepared by Technical Committee CEN/TC 88 Thermal insulating
materials and products. However,
⎯ 6.2, conditioning of the test specimens,
⎯ 7.1, test conditions, and
⎯ Clause 10, test report
have been modified to reflect the conditions for tropical countries. Further, Clause 8 has been modified.
© ISO 2010 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 29803:2010(E)
This International Standard is based on EN 13497:2002 prepared by Technical Committee CEN/TC 88
Thermal insulating materials and products, which has been amended by ISO/TC 163/SC 1 with reference to
conditioning and testing conditions in tropical countries.
This International Standard is one of a series of documents specifying test methods, based on existing
European Standards, that are being adopted by ISO. This “package” of standards includes the following group
of interrelated documents.
International Title Respective
Standard EN standard
12968 Thermal insulation products for building applications — Determination of the EN 13495
pull-off resistance of external thermal insulation composite systems (ETICS)
(foam block test)
29465 Thermal insulating products for building applications — Determination of EN 822
length and width
29466 Thermal insulating products for building applications — Determination of EN 823
thickness
29467 Thermal insulating products for building applications — Determination of EN 824
squareness
Thermal insulating products for building applications — Determination of EN 825
29468
flatness
29469 Thermal insulating products for building applications — Determination of EN 826
compression behaviour
29470 Thermal insulating products for building applications — Determination of the EN 1602
apparent density
29471 Thermal insulating products for building applications — Determination of EN 1603
dimensional stability under constant normal laboratory conditions (23°C/50 %
relative humidity)
29472 Thermal insulating products for building applications — Determination of EN 1604
dimensional stability under specified temperature and humidity conditions
29764 Thermal insulating products for building applications — Determination of EN 1605
deformation under specified compressive load and temperature conditions
29765 Thermal insulating products for building applications — Determination of EN 1607
tensile strength perpendicular to faces
29766 Thermal insulating products for building applications — Determination of EN 1608
tensile strength parallel to faces
Thermal insulating products for building applications — Determination of
29767 EN 1609
short-term water absorption by partial immersion
29768 Thermal insulating products for building applications — Determination of linear EN 12085
dimensions of test specimens
29769 Thermal insulating products for building applications — Determination of EN 12430
behaviour under point load
29770 Thermal insulating products for building applications — Determination of EN 12431
thickness for floating-floor insulating products
29771 Thermal insulating materials for building applications — Determination of EN 13820
organic content
Thermal insulation products for building applications — Determination of the
29803 EN 13497
resistance to impact of external thermal insulation composite systems (ETICS)
29804 Thermal insulation products for building applications — Determination of the EN 13494
tensile bond strength of the adhesive and of the base coat to the thermal
insulation material
Thermal insulation products for building applications — Determination of the
29805 EN 13496
mechanical properties of glass fibre meshes
iv © ISO 2010 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 29803:2010(E)
Thermal insulation products for building applications —
Determination of the resistance to impact of external thermal
insulation composite systems (ETICS)
1 Scope
This International Standard specifies equipment and a procedure for determining the resistance to impact of
external thermal insulation composite systems (ETICS).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 29466, Thermal insulating products for building applications — Determination of thickness
ISO 29470, Thermal insulating products for building applications — Determination of the apparent density
ISO 29765, Thermal insulating products for building applications — Determination of tensile strength
perpendicular to faces
EN 13499, Thermal insulation products for buildings — External thermal insulation composite systems
(ETICS) based on expanded polystyrene — Specification
ISO 3251, Paints, varnishes and plastics — Determination of non-volatile matter content
ISO 9229, Thermal insulation — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 9229 and EN 13499 apply.
4 Principle
The resistance to im
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.