ISO 29771:2008
(Main)Thermal insulating materials for building applications — Determination of organic content
Thermal insulating materials for building applications — Determination of organic content
ISO 29771:2008 specifies the equipment and procedures for determining the organic content of thermal insulating materials. The method is aimed at determining the organic content for products that are inorganic, i.e. products containing a low percentage of organic compounds, either unfaced products or the insulating material of a faced product. ISO 29771:2008 is not applicable for the determination of organic content in the presence of water of hydration and/or combined carbonate, sulfate, etc. ISO 29771:2008 is not applicable for the determination of organic content of adhesives, facings and/or coatings.
Matériaux isolants thermiques destinés aux applications du bâtiment — Détermination du contenu organique
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 29771
First edition
2008-11-01
Thermal insulating materials for building
applications — Determination of organic
content
Matériaux isolants thermiques destinés aux applications du bâtiment —
Détermination du contenu organique
Reference number
©
ISO 2008
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Terms and definitions .1
3 Principle.1
4 Apparatus.1
5 Test specimens.2
6 Procedure.2
7 Calculation and expression of results .3
8 Accuracy of measurement.3
9 Test report.4
Annex A (informative) Example of a simplified method for the determination of organic content.5
Bibliography.7
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 29771 was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the
built environment, Subcommittee SC 1, Test and measurement methods.
iv © ISO 2008 – All rights reserved
Introduction
This International Standard comprises the original EN 13820:2003 prepared by Technical Committee
CEN/TC 88, Thermal insulating materials and products, which has been amended by ISO/TC 163/SC 1 with
reference to conditioning and testing conditions in tropical countries.
This International Standard is one of a series of documents specifying test methods, based on existing
European Standards, that are being adopted by ISO. This “package” of standards includes the following group
of interrelated documents.
International Standard Respective
EN standard
ISO 29465, Thermal insulating products for building applications — Determination of length EN 822
and width
ISO 29466, Thermal insulating products for building applications — Determination of EN 823
thickness
ISO 29467, Thermal insulating products for building applications — Determination of EN 824
squareness
ISO 29468, Thermal insulating products for building applications — Determination of flatness EN 825
ISO 29469, Thermal insulating products for building applications — Determination of EN 826
compression behaviour
ISO 29470, Thermal insulating products for building applications — Determination of the EN 1602
apparent density
ISO 29471, Thermal insulating products for building applications — Determination of EN 1603
dimensional stability under constant normal laboratory conditions (23 °C/50 % relative
humidity)
ISO 29472, Thermal insulating products for building applications — Determination of EN 1604
dimensional stability under specified temperature and humidity conditions
ISO 29764, Thermal insulating products for building applications — Determination of EN 1605
deformation under specified compressive load and temperature conditions
ISO 29765, Thermal insulating products for building applications — Determination of tensile EN 1607
strength perpendicular to faces
ISO 29766, Thermal insulating products for building applications — Determination of tensile EN 1608
strength parallel to faces
ISO 29767, Thermal insulating products for building applications — Determination of short- EN 1609
term water absorption by partial immersion
ISO 29768, Thermal insulating products for building applications — Determination of linear EN 12085
dimensions of test specimens
ISO 29769, Thermal insulating products for building applications — Determination of EN 12430
behaviour under point load
ISO 29770, Thermal insulating products for building applications — Determination of EN 12431
thickness for floating-floor insulating products
ISO 29771, Thermal insulating materials for building applications — Determination of organic EN 13820
content
ISO 29803, Thermal insulation products for building applications — Determination of the EN 13497
resistance to impact of external thermal insulation composite systems (ETICS)
ISO 29804, Thermal insulation products for building applications — Determination of the EN 13494
tensile bond strength of the adhesive and of the base coat to the thermal insulation material
ISO 29805, Thermal insulation products for building applications — Determination of the EN 13496
mechanical properties of glass fibre meshes
This International Standard has been prepared for products used to insulate buildings, building equipment and
industrial installation, but it may also be applied for products used in other areas.
vi © ISO 2008 – All rights reserved
INTERNATIONAL STANDARD ISO 29771:2008(E)
Thermal insulating materials for building applications —
Determination of organic content
1 Scope
This International Standard specifies the equipment and procedures for determining the organic content of
thermal insulating materials.
The method is aimed at determining the organic content for products that are inorganic, i.e. products
containing a low percentage of organic compounds, either unfaced products or the insulating material of a
faced product.
This International Standard is not applicable for the determination of organic content in the presence of water
of hydration and/or combined carbonate, sulfate, etc.
This International Standard is not applicable for the determination of organic content of adhesives, facings
and/or coatings.
NOTE This International Standard can be used to verify that a thermal insulating product complies with the
requirements of EN 13501-1 for classification as Euroclass A1 without testing.
2 Terms and definitions
For the purposes of this document, the following term a
...
INTERNATIONAL ISO
STANDARD 29771
First edition
2008-11-01
Thermal insulating materials for building
applications — Determination of organic
content
Matériaux isolants thermiques destinés aux applications du bâtiment —
Détermination du contenu organique
Reference number
©
ISO 2008
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Terms and definitions .1
3 Principle.1
4 Apparatus.1
5 Test specimens.2
6 Procedure.2
7 Calculation and expression of results .3
8 Accuracy of measurement.3
9 Test report.4
Annex A (informative) Example of a simplified method for the determination of organic content.5
Bibliography.7
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 29771 was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the
built environment, Subcommittee SC 1, Test and measurement methods.
iv © ISO 2008 – All rights reserved
Introduction
This International Standard comprises the original EN 13820:2003 prepared by Technical Committee
CEN/TC 88, Thermal insulating materials and products, which has been amended by ISO/TC 163/SC 1 with
reference to conditioning and testing conditions in tropical countries.
This International Standard is one of a series of documents specifying test methods, based on existing
European Standards, that are being adopted by ISO. This “package” of standards includes the following group
of interrelated documents.
International Standard Respective
EN standard
ISO 29465, Thermal insulating products for building applications — Determination of length EN 822
and width
ISO 29466, Thermal insulating products for building applications — Determination of EN 823
thickness
ISO 29467, Thermal insulating products for building applications — Determination of EN 824
squareness
ISO 29468, Thermal insulating products for building applications — Determination of flatness EN 825
ISO 29469, Thermal insulating products for building applications — Determination of EN 826
compression behaviour
ISO 29470, Thermal insulating products for building applications — Determination of the EN 1602
apparent density
ISO 29471, Thermal insulating products for building applications — Determination of EN 1603
dimensional stability under constant normal laboratory conditions (23 °C/50 % relative
humidity)
ISO 29472, Thermal insulating products for building applications — Determination of EN 1604
dimensional stability under specified temperature and humidity conditions
ISO 29764, Thermal insulating products for building applications — Determination of EN 1605
deformation under specified compressive load and temperature conditions
ISO 29765, Thermal insulating products for building applications — Determination of tensile EN 1607
strength perpendicular to faces
ISO 29766, Thermal insulating products for building applications — Determination of tensile EN 1608
strength parallel to faces
ISO 29767, Thermal insulating products for building applications — Determination of short- EN 1609
term water absorption by partial immersion
ISO 29768, Thermal insulating products for building applications — Determination of linear EN 12085
dimensions of test specimens
ISO 29769, Thermal insulating products for building applications — Determination of EN 12430
behaviour under point load
ISO 29770, Thermal insulating products for building applications — Determination of EN 12431
thickness for floating-floor insulating products
ISO 29771, Thermal insulating materials for building applications — Determination of organic EN 13820
content
ISO 29803, Thermal insulation products for building applications — Determination of the EN 13497
resistance to impact of external thermal insulation composite systems (ETICS)
ISO 29804, Thermal insulation products for building applications — Determination of the EN 13494
tensile bond strength of the adhesive and of the base coat to the thermal insulation material
ISO 29805, Thermal insulation products for building applications — Determination of the EN 13496
mechanical properties of glass fibre meshes
This International Standard has been prepared for products used to insulate buildings, building equipment and
industrial installation, but it may also be applied for products used in other areas.
vi © ISO 2008 – All rights reserved
INTERNATIONAL STANDARD ISO 29771:2008(E)
Thermal insulating materials for building applications —
Determination of organic content
1 Scope
This International Standard specifies the equipment and procedures for determining the organic content of
thermal insulating materials.
The method is aimed at determining the organic content for products that are inorganic, i.e. products
containing a low percentage of organic compounds, either unfaced products or the insulating material of a
faced product.
This International Standard is not applicable for the determination of organic content in the presence of water
of hydration and/or combined carbonate, sulfate, etc.
This International Standard is not applicable for the determination of organic content of adhesives, facings
and/or coatings.
NOTE This International Standard can be used to verify that a thermal insulating product complies with the
requirements of EN 13501-1 for classification as Euroclass A1 without testing.
2 Terms and definitions
For the purposes of this document, the following term a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.