Diesel engines — Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems — Mounting dimensions

ISO 7612:2009 specifies dimensional requirements for base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems for diesel (compression-ignition) engines.

Moteurs diesels — Pompes d'injection en ligne à fixation par base plane et pompes d'alimentation à haute pression pour systèmes d'injection de carburant à rampe commune — Dimensions de montage

General Information

Status
Withdrawn
Publication Date
04-Oct-2009
Withdrawal Date
04-Oct-2009
Current Stage
9599 - Withdrawal of International Standard
Completion Date
15-Oct-2018
Ref Project

Relations

Buy Standard

Standard
ISO 7612:2009 - Diesel engines -- Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems -- Mounting dimensions
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 7612
Fourth edition
2009-10-15

Diesel engines — Base-mounted in-line
fuel injection pumps and high-pressure
supply pumps for common rail fuel
injection systems — Mounting
dimensions
Moteurs diesels — Pompes d'injection en ligne à fixation par base plane
et pompes d'alimentation à haute pression pour systèmes d'injection de
carburant à rampe commune — Dimensions de montage




Reference number
ISO 7612:2009(E)
©
ISO 2009

---------------------- Page: 1 ----------------------
ISO 7612:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 7612:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7612 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 7, Injection
equipment and filters for use on road vehicles.
This fourth edition cancels and replaces the third edition (ISO 7612:2006), which has been technically revised.
© ISO 2009 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 7612:2009(E)

Diesel engines — Base-mounted in-line fuel injection pumps
and high-pressure supply pumps for common rail fuel injection
systems — Mounting dimensions
1 Scope
This International
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.