ISO/IEC 11694-2:2000

Identification cards — Optical memory cards — Linear recording method — Part 2: Dimensions and location of the accessible optical area

Cartes d'identification — Cartes à mémoire optique — Méthode d'enregistrement linéaire — Partie 2: Dimensions et emplacement de la zone optique accessible

General Information

• Status: Withdrawn
• Publication Date: 12-Apr-2000
• Withdrawal Date: 12-Apr-2000
• ICS: 35.240.15 - Identification cards. Chip cards. Biometrics
• Technical Committee: ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification
• Drafting Committee: ISO/IEC JTC 1/SC 17 - Cards and security devices for personal identification
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 19-Sep-2005

Relations

• Revised: ISO/IEC 11694-2:2005 - Identification cards — Optical memory cards — Linear recording method — Part 2: Dimensions and location of the accessible optical area
• Effective Date: 15-Apr-2008
• Revises: ISO/IEC 11694-2:1995 - Identification cards — Optical memory cards — Linear recording method — Part 2: Dimensions and location of the accessible optical area
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 11694-2
Second edition
2000-04-15
Identification cards — Optical memory
cards — Linear recording method —
Part 2:
Dimensions and location of the accessible
optical area
Cartes d'identification — Cartes à mémoire optique — Méthode
d'enregistrement linéaire —
Partie 2: Dimensions et emplacement de la zone optique accessible
Reference number
ISO/IEC 11694-2:2000(E)
©
ISO/IEC 2000

---------------------- Page: 1 ----------------------
ISO/IEC 11694-2:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO/IEC 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO/IEC 2000 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 11694-2:2000(E) © ISO/IEC
Introduction
This part of ISO/IEC 11694 is one of a series of standards describing the parameters for optical memory cards and
the use of such cards for the storage and interchange of digital data.
The standards recognize the existence of different methods for recording and reading information on optical
memory cards, the characteristics of which are specific to the recording method employed. In general, these
different recording methods will not be compatible with each other. Therefore, the standards are structured to
accommodate the inclusion of existing and future recording methods in a consistent manner.
This part of ISO/IEC 11694 is specific to optical memory cards using the linear recording method. Characteristics
which apply to other specific recording methods shall be found in separate standards documents.
This part of ISO/IEC 11694 defines the dimensions and location of the accessible optical area and the extent of
compliance with, addition to, and/or deviation from the relevant base document, ISO/IEC 11693.
The user's attention is called to the possibility that compliance with this part of ISO/IEC 11694 may require use of an
invention covered by patent rights and/or other material covered by copyrights. By publication of this part of
ISO/IEC 11694, no position is taken with respect to the validity of this claim or of any patent rights or copyrights in
connection therewith.
iv

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD © ISO/IEC ISO/IEC 11694-2:2000(E)
Identification cards — Optical memory cards — Linear recording
method — Part 2: Dimensions and location of the accessible
optical area
1 Scope
This part of ISO/IEC 11694 defines the dimensions and location of the accessible optical area of optical memory
cards with ID-1 dimensions using the linear recording method.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO/IEC 11694. For dat
...