Diesel engines -- Fuel injection pumps -- Tapers for shaft ends and hubs

ISO 6519:2015 specifies the dimensions of tapered shaft ends and hubs of fuel injection pumps and common-rail high pressure pumps for diesel (compression-ignition) engines. The specified shaft ends and hubs may be used with or without Woodruff keys. NOTE The specified shaft ends and hubs can also be used for other applications where no specific standards exist.

Moteurs diesels -- Pompes d'injection de combustible -- Cônes pour bouts d'arbre et moyeux

General Information

Status
Published
Publication Date
22-Jul-2015
Current Stage
9020 - International Standard under periodical review
Start Date
15-Jul-2020
Ref Project

RELATIONS

Buy Standard

Standard
ISO 6519:2015 - Diesel engines -- Fuel injection pumps -- Tapers for shaft ends and hubs
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 6519
Fourth edition
2015-08-15
Diesel engines — Fuel injection pumps
— Tapers for shaft ends and hubs
Moteurs diesels — Pompes d’injection de combustible — Cônes pour
bouts d’arbre et moyeux
Reference number
ISO 6519:2015(E)
ISO 2015
---------------------- Page: 1 ----------------------
ISO 6519:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 6519:2015(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Dimensions and tolerances ....................................................................................................................................................................... 1

2.1 General ........................................................................................................................................................................................................... 1

2.2 Shaft ends with taper ........................................................................................................................................................................ 1

2.3 Keyways of hub with taper ........................................................................................................................................................... 1

© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 6519:2015(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.
For an explanation on th
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.