ISO/IEC 11694-2:2012
(Main)Identification cards — Optical memory cards — Linear recording method — Part 2: Dimensions and location of the accessible optical area
Identification cards — Optical memory cards — Linear recording method — Part 2: Dimensions and location of the accessible optical area
ISO/IEC 11694-2:2012 defines the dimensions and location of the accessible optical area of optical memory cards with ID-1 dimensions using the linear recording method.
Cartes d'identification — Cartes à mémoire optique — Méthode d'enregistrement linéaire — Partie 2: Dimensions et emplacement de la zone optique accessible
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO/IEC
STANDARD 11694-2
Fourth edition
2012-12-15
Identification cards — Optical memory
cards
Part 2:
Dimensions and location of the
accessible optical area
Cartes d'identification — Cartes à mémoire optique
Partie 2: Dimensions et emplacement de la zone optique accessible
Reference number
ISO/IEC 11694-2:2012(E)
©
ISO/IEC 2012
---------------------- Page: 1 ----------------------
ISO/IEC 11694-2:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/IEC 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2012 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/IEC 11694-2:2012(E)
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions and location . 1
4.1 General . 1
4.2 Accessible optical area . 1
4.2.1 Dimension C . 1
4.2.2 Dimension X . 1
4.2.3 Dimension Y . 2
4.2.4 Skew . 2
Annex A (informative) Optional card layouts . 3
A.1 General . 3
A.2 Accessible optical area . 3
A.2.1 Location . 3
A.2.2 Reference track . 3
A.2.3 Size . 3
A.2.4 Co-existence . 3
Bibliography . 4
© ISO/IEC 2012 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/IEC 11694-2:2012(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 11694-2 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 17, Cards and persona
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.