ISO/FDIS 7039
(Main)Metallic materials — Tensile testing — Method for evaluating the susceptibility of materials to the effects of high-pressure gas within hollow test pieces
Metallic materials — Tensile testing — Method for evaluating the susceptibility of materials to the effects of high-pressure gas within hollow test pieces
Matériaux métalliques — Essais de traction — Méthode d'évaluation des changements de propriétés dans un environnement gazeux à haute pression en utilisant une pièce d'essai creuse
General Information
Buy Standard
Standards Content (Sample)
FINAL DRAFT
International
Standard
ISO/FDIS 7039
ISO/TC 164/SC 1
Metallic materials — Tensile
Secretariat: AFNOR
testing — Method for evaluating the
Voting begins on:
susceptibility of materials to the
2024-05-08
effects of high-pressure gas within
Voting terminates on:
hollow test pieces
2024-07-03
Matériaux métalliques — Essais de traction — Méthode
d'évaluation des changements de propriétés dans un
environnement gazeux à haute pression en utilisant une pièce
d'essai creuse
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 7039:2024(en) © ISO 2024
---------------------- Page: 1 ----------------------
FINAL DRAFT
ISO/FDIS 7039:2024(en)
International
Standard
ISO/FDIS 7039
ISO/TC 164/SC 1
Metallic materials — Tensile
Secretariat: AFNOR
testing — Method for evaluating the
Voting begins on:
susceptibility of materials to the
effects of high-pressure gas within
Voting terminates on:
hollow test pieces
Matériaux métalliques — Essais de traction — Méthode
d'évaluation des changements de propriétés dans un
environnement gazeux à haute pression en utilisant une pièce
d'essai creuse
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
COPYRIGHT PROTECTED DOCUMENT
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2024
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 7039:2024(en) © ISO 2024
© ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO/FDIS 7039:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 Principle . 2
6 Test piece . 3
6.1 General .
...
ISO DIS/FDIS 7039:2024(E)
ISO /TC 164/SC 1/WG 9
Date: 2024-02-29
Secretariat: AFNOR
Date: 2024-04-24
Metallic materials — Tensile testing — Method for evaluating the
susceptibility of materials to the effects of high-pressure gas within
hollow test pieces
Matériaux métalliques — Essais de traction — Méthode d'évaluation des changements de propriétés dans un
environnement gazeux à haute pression en utilisant une pièce d'essai creuse
FDIS stage
---------------------- Page: 1 ----------------------
ISO/DIS FDIS 7039:2024(Een)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. Dede Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: copyright@iso.org
Website: www.iso.orgwww.iso.org
Published in Switzerland
ii © ISO 2024 – All rights reserved
ii
---------------------- Page: 2 ----------------------
ISO/DIS FDIS 7039:2024(Een)
Contents
Foreword . v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 Principle . 3
6 Test piece . 3
6.1 General . 3
6.2 Shape and dimensions . 3
6.3 Inner surface of hole . 4
6.4 Number of test pieces . 4
7 Measurement of original cross-sectional area . 4
8 Marking the original gauge length . 4
9 Test equipment . 4
9.1 Principle . 4
9.2 Testing machine . 6
9.3 Extensometer . 6
9.4 Test deviation . 6
10 Test conditions . 6
10.1 Test gas . 6
10.2 Test temperature . 7
10.3 Test pressure .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.