ISO 13315-1:2012
(Main)Environmental management for concrete and concrete structures — Part 1: General principles
Environmental management for concrete and concrete structures — Part 1: General principles
1 Scope This part of ISO 13315 provides a framework and basic rules on environmental management related to concrete and concrete structures. This includes the assessment of the environmental impacts and methods of implementing environmental improvement based on the assessment. This part of ISO 13315 is used when assessing the environmental impacts and implementing the environmental management of concrete and concrete structures for the environmental consideration in activities related to the production of concrete constituents, the production, recycling and disposal of concrete, and the design, execution, use and demolition of concrete structures. It is applied for their entire lifecycles, respective stages of the lifecycles, or certain ranges of the lifecycles. This part of ISO 13315 is relevant to newly produced concrete and newly constructed concrete structures, and also existing concrete and concrete structures. This part of ISO 13315 applies not only to single concretes but also to concrete families and not only to single concrete structures but also to concrete structure complexes. For materials other than concrete, the related ISO standards are applied where available. In the case where no ISO standard is available, such materials are appropriately dealt with referring to this part of ISO 13315 and the normative references. The environments covered by this part of ISO 13315 include global, regional and local environments. The indoor pollution of buildings and the environments for workers in concrete producing plants and on concrete structure construction sites are not specifically covered by this part of ISO 13315. This part of ISO 13315 does not directly deal with the environmental impacts resulting from the operation of equipment installed in concrete structures. However, the special properties of concrete and concrete structures affecting the operational efficiency of such equipment are considered in this part of ISO 13315. This part of ISO 13315 covers secondary effects of the production of concrete and execution of concrete structures. This part of ISO 13315 may also cover the economic and social effects of environmental consideration in the production of concrete and execution of concrete structures. NOTE 1 ISO 16814 is available for reference as a standard for the indoor pollution of buildings. NOTE 2 The working environments of plants and construction sites are generally prescribed by industrial safety and health laws. NOTE 3 In buildings, global warming substances are mainly emitted from energy consumption due to the operation of heating, ventilating and air-conditioning equipment. NOTE 4 The beneficial effects such as thermal mass and other functions of concrete and concrete structures may be taken into account. NOTE 5 The secondary effects of the production of concrete include the future possibility of leaching of heavy metals from concrete or the absorption of heavy metals from the environment, the effect of waste treatments on the environment, etc.
Management environnemental du béton et des structures en béton — Partie 1: Principes généraux
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 13315-1
First edition
2012-02-15
Environmental management for concrete
and concrete structures —
Part 1:
General principles
Management environnemental du béton et des structures en béton —
Partie 1: Principes généraux
Reference number
ISO 13315-1:2012(E)
©
ISO 2012
---------------------- Page: 1 ----------------------
ISO 13315-1:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 13315-1:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 General framework . 3
4.1 General . 3
4.2 Phases in the lifecycle . 4
4.3 Environmental impact categories . 4
4.4 Analysis . 5
4.5 Design phase . 6
4.6 Production/execution phase . 7
4.7 Use phase . 7
4.8 End of life phase . 8
4.9 Labels and declaration . 9
Annex A (informative) Phases and environmental impact factors to be considered in lifecycle of
concrete and concrete structures .10
Bibliography .14
© ISO 2012 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 13315-1:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.