SIST EN ISO 294-3:2000

Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:1996)

Kunststoffe - Spritzgießen von Probekörpern aus Thermoplasten - Teil 3: Kleine Platten (ISO 294-3:1996)

Siehe ISO 294-1:1996, Abschnitt 1. Dieser Teil von ISO 294 legt zwei Zweifachwerzeuge fest, die ISO Typ D1 und D2 Werkzeuge zum Spritzgießen kleiner Platten 60 mm x 60 mm mit den Vorzugsdicken von 1 mm (Typ D1) und 2 mm (Typ D2), die für eine Vielzahl von Prüfungen benutzt werden können (siehe Anhang A). Die Werkzeuge können zusätzlich mit Einsätzen versehen werden zur Untersuchung der Wirkung von Fließnähten auf mechanische Eigenschaften (siehe Anhang B).

Plastiques - Moulage par injection des éprouvettes de matériaux thermoplastiques - Partie 3: Plaques de petites dimensions (ISO 294-3:1996)

Polimerni materiali - Vbrizgavanje plastomernih preskušancev - 3. del: Ploščice (ISO 294-3:1996)

General Information

• Status: Withdrawn
• Publication Date: 30-Apr-2000
• Withdrawal Date: 30-Nov-2003
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 01-Dec-2003
• Due Date: 01-Dec-2003
• Completion Date: 01-Dec-2003
• Ref Project: EN ISO 294-3:1998 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:1996)

Relations

• Replaced By: SIST EN ISO 294-3:2003 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2002)
• Effective Date: 01-Dec-2003
• Parent: SIST EN ISO 294-1:2000 - Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:1996)
• Effective Date: 22-Dec-2008
• Replaces: SIST ISO 294-3:1997 - Plastics -- Injection moulding of test specimens of thermoplastic materials -- Part 3: Small plates
• Effective Date: 01-May-2000

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 294-3:2000
01-maj-2000
3ROLPHUQLPDWHULDOL9EUL]JDYDQMHSODVWRPHUQLKSUHVNXãDQFHYGHO3ORãþLFH
,62
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small
plates (ISO 294-3:1996)
Kunststoffe - Spritzgießen von Probekörpern aus Thermoplasten - Teil 3: Kleine Platten
(ISO 294-3:1996)
Plastiques - Moulage par injection des éprouvettes de matériaux thermoplastiques -
Partie 3: Plaques de petites dimensions (ISO 294-3:1996)
Ta slovenski standard je istoveten z: EN ISO 294-3:1998
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 294-3:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 294-3:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 294-3:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 294-3:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 294-3:2000

---------------------- Page: 5 ----------------------

SIST EN ISO 294-3:2000

---------------------- Page: 6 ----------------------

SIST EN ISO 294-3:2000
IS0
INTERNATIONAL
STANDARD 294-3
First edition
1996-12-15
- Injection moulding of test
Plastics
specimens of thermoplastic materials -
Part 3:
Small plates
P/as tiques - Moulage par injection des gprouvettes de matkiaux
thermoplastiques -
Partie 3: Plaques de petites dimensions
Reference number
IS0 294-3:1996(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 294-3:2000
IS0 294-3: 1996(E)
Foreword
a worldwide
IS0 (the International Organization for Standardization) is
federation of national standards bodies (IS0 member bodies) The work of
preparing International Standards is normally carried out ‘through IS0
3 subject for
technical committees. Each member body interested in 2
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 294-3 was prepared by Technical Committee
ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.
Together with the other parts, this part of IS0 294 cancels and replaces
the second edition of IS0 294 (IS0 294:1995) which has been revised to
improve the definition of the injection-moulding parameters and has been
restructured to specify four types of IS0 mould for the production of the
basic specimen types required for the acquisition of comparable test data.
Care has been taken to ensure that the IS0 moulds described can all be
fitted in existing injection-moulding equipment and have interchangeable
cavity plates.
IS0 294 consists of the following parts, under the general title Plastics -
Injection mouldlng of test specimens of thermoplastic materials:
- Part 7: General principles, and moulding of multipurpose and bar test
specimens
- Part 2: Small tensile bars
- Part 3: Small plates
Part 4: Determination of moulding shrinkage
Annexes A to C of this part of IS0 294 are for information only.
0 IS0 1996
All rights reserved. Unless otherwise specified, no part of this publication may be
reproduced or utilized in any form or by any means, electronic or mechanrcal, including
photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 294-3:2000
INTERNATIONAL STANDARD @ IS0 IS0 294=3:1996(E)
Plastics - Injection moulding of test specimens of thermoplastic
materials -
Part 3:
Small plates
1 Scope
This part of IS0 294 specifies two two-cavity moulds, the type Dl and D2 IS0 moulds, for the injection moulding of
small plates measuring 60 mm x 60 mm with a preferred thickness of ‘I mm (type Dl) or 2 mm (type D2) which
can be used for a variety of tests (see annex A). The moulds may additionally be fitted with inserts for studying the
effects of weld lines on the mechanical properties (see annex B).
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this part
of IS0 294. At the time of publication, the editions indicated were valid. All standards are subject to revision, and
parties to agreements based on this part of IS0 294 are encouraged to investigate the possibility of applying the
most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently
valid International Standards.
P/as tics
I SO 294-l : 1996, - Injection moulding of test specimens of thermoplastic materials - Part 1: General
principles, and moulding of multipurpose and bar test specimens.
I SO 294-4:- I), P/as tics - Injection moulding of test specimens of thermoplastic materials - Part 4: Determi-
nation of moulding shrinkage.
IS0 6603-I : 1985, Plastics - Determination of multiaxial impact behaviour of rigid plastics - Part 7: Falling dart
method.
I SO 6603-2: 1989, P/as tics - Determination of multiaxial impact behaviour of rigid plastics - Part 2: Instrumented
puncture test.
3 Definitions
See IS0 294-l :1996, clause 3.
1) To be published. (Revision in part of IS0 294:1995)

---------------------- Page: 9 ----------------------

SIST EN ISO 294-3:2000
@ IS0
IS0 294=3:1996(E)
4 Apparatus
4.1 Type Dl and D2 IS0 moulds
Type Dl and 02 IS0 moulds are two-cavity moulds (see figure 1) intended for the preparation of plates measuring
60 mm x 60 mm. The plates produced using these moulds shall have the dimensions given in figure 2.
The main constructional details of type Dl and D2 IS0 moulds shall be as shown in figures 1 and 2 and shall meet
the following requirements:
See IS0 294-l :I 996, subclause 4.1 .I .4, item a).
a)
Not applicable.
b)
c) See IS0 294-l :I 996, subclause 4.1 .I .4, item c).
d) and e) Not applicable.
f ) See IS0 294-l :I 996, subclause 4.1.1.4, item f).
See IS0 294-l :I 996, subclause 4.1 .I .4, item g), but with reference to IS0 6603.
9)
The main dimensions, in millimetres, of the cavities shall be as follows (see also figure 2):
- length: 60 to 62;
- width: 60 to 62;
- depth: type D2 mould 2,0 to 2,1
type Dl mould 1 ,O to 1 ,I.
X
X-Y
I- G G
I
I I
w
Sprue Moulding volume u/M = 30 000 mm3 (at 2 mm thickness)
SP
G Gate Projected area AP = 11 000 mm2
is the distance between the lines along which the test specimens are cut
k
from the runners (see notes 3 and 4 in subclause 4.1)
Figure 1 - Cavity plate for type Dl and D2 IS0 moulds
2

---------------------- Page: 10 ----------------------

SIST EN ISO 294-3:2000
IS0 294=3:1996(E)
Key
Sprue
SP
G Gate
Runner
R
P Pressure sensor
Dimensions in mm
l Length of plate 60+2 ’)
b Width of plate 60+2- ’)
Thickness of plate:type Dl mould I ,o Ii- 0,l
h
type D2 mould 2,0 + 0,l 1)
Length of gate 4,0 + 0,l 2)
lG
Height of gate (0,75 + 0,05) x h3)
hG
Length of runner 25 to 304)
lR
Width of runner at gate a(b + 6)
bR
Depth of runner at gate h + (I,5 &0,5)
hR
I* Unspecified distance
Distance of pressure sensor from gate 5+25) -
LP
1) These dimensions are for the preferred test specimen used in IS0 6603.
2) See notes 2 and 3 in subclause 4.1.
3) See notes 1 and 2 in subclause 4.1.
4) See note 4 in subclause 4.1.
5) The position of the pressure sensor shall be further limited by the following
conditions:
zp+rp c 10
zp-rp 2 0
where rp is the radius of the sensor.
Figure 2 - Details of type Dl and D2 IS0 moulds

---------------------- Page: 11 ----------------------

SIST EN ISO 294-3:2000
@ IS0
IS0 294=3:1996(E)
See IS0 294-1 :I 996, subclause 4.1 .I .4, items h) to j).
h) to j>
Figure 2 shows the position of a pressure sensor P within the cavity, which is mandatory for the
k)
measure
...