SIST EN ISO 2898-2:2000

Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2898-2:1997)

Kunststoffe - Weichmacherhaltige Polyvinylchlorid (PVC-P)-Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 2898-2:1997)

Plastiques - Matériaux a base de poly(chlorure de vinyle) plastifié (PVC-P) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 2898-2:1997)

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz mehčanega polivinilklorida (PVC-P) - 2. del: Priprava preskušancev in določanje lastnosti (ISO 2898-2:1997)

General Information

• Status: Withdrawn
• Publication Date: 30-Apr-2000
• Withdrawal Date: 11-Mar-2009
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 12-Feb-2009
• Due Date: 07-Mar-2009
• Completion Date: 12-Mar-2009
• Ref Project: EN ISO 2898-2:1999 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2898-2:1997)

Relations

• Replaced By: SIST EN ISO 2898-2:2009 - Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2898-2:2008)
• Effective Date: 01-Apr-2009

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 2898-2:2000
01-maj-2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]PHKþDQHJD
SROLYLQLONORULGD39&3GHO3ULSUDYDSUHVNXãDQFHYLQGRORþDQMHODVWQRVWL,62

Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part
2: Preparation of test specimens and determination of properties (ISO 2898-2:1997)
Kunststoffe - Weichmacherhaltige Polyvinylchlorid (PVC-P)-Formmassen - Teil 2:
Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 2898-2:1997)
Plastiques - Matériaux a base de poly(chlorure de vinyle) plastifié (PVC-P) pour moulage
et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO
2898-2:1997)
Ta slovenski standard je istoveten z: EN ISO 2898-2:1999
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 2898-2:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2898-2:2000

---------------------- Page: 2 ----------------------

SIST EN ISO 2898-2:2000

---------------------- Page: 3 ----------------------

SIST EN ISO 2898-2:2000

---------------------- Page: 4 ----------------------

SIST EN ISO 2898-2:2000

---------------------- Page: 5 ----------------------

SIST EN ISO 2898-2:2000

---------------------- Page: 6 ----------------------

SIST EN ISO 2898-2:2000
IS0
INTERNATIONAL
2898-2
STANDARD
Third edition
1997-07-I 5
Plastics - Plasticized poly(vinyl chloride)
(PVC-P) moulding and extrusion materials -
Part 2:
Preparation of test specimens
and determination of properties
Plastiques - Matbriaux B base de poly(chlorure de viny) plastifid (PVC-P)
pour moulage et extrusion -
Partie 2: Pkparation des gprouvettes et dktermination des propri&&
Reference number
IS0 2898-2: 1997(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 2898-2:2000
IS0 2898-2: 1997(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies
casting a vote.
International Standard IS0 2898-2 was prepared by Technical Committee
ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.
This third edition cancels and replaces the second edition
(IS0 2898,2:1989) and includes the following changes:
- the text has been brought into accordance with the standard SC 9
frame text;
- the test conditions for tensile stress and volume resistivity have been
revised in accordance with IS0 10350.
IS0 2898 consists of the following parts, under the general title Plastics -
Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials:
- Part 1: Designation system and basis for specifications
- Parf2: Preparation of test specimens and determination of
properties
Annex A forms an integral part of this part of IS0 2898.
0 IS0 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 l CH-1211 Geneve 20 l Switzerland
Internet central @ iso.ch
c=ch; a=400net; p=iso; o=isocs; s=central
x.400
Printed in Switzerland

---------------------- Page: 8 ----------------------

SIST EN ISO 2898-2:2000
IS0 2898-2: 1997(E)
INTERNATIONAL STANDARD @ IS0
Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding
and extrusion materials -
Part 2:
Preparation of test specimens and determ ination of properties
1 Scope
This part of IS0 2898 specifies the methods of preparation of test specimens and the test methods to be used in
determining the properties of PVC-P moulding and extrusion materials. Requirements for handling test material and
for conditioning both the test material before moulding and the specimens before testing are given here.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the
materials from which these specimens are made are given. Properties and test methods which are suitable and
necessary to characterize PVC-P moulding and extrusion materials are listed.
The properties have been selected from the general test methods in IS0 10350. Other test methods in wide use for
or of particular significance to these moulding and extrusion materials are also included in this part of IS0 2898,
as are the designatory properties specified in part 1.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and
conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not
necessarily be identical to those obtained using specimens of different dimensions or prepared using different
procedures.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this part of
IS0 2898. At the time of publication, the editions indicated were valid. All standards are subject to revision, and
parties to agreements based on this part of IS0 2898 are encouraged to investigate the possibility of applying the
most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid
International Standards.
IS0 176:1976, Plastics - Determination of loss of plasticizers - Activated carbon method.
- Standard atmospheres for conditioning and testing.
IS0 291 :-V, Plastics
IS0 293:1986, Plastics - Compression moulding test specimens of thermoplastic materials.
1) To be published. (Revision of IS0 291:1977)
1

---------------------- Page: 9 ----------------------

SIST EN ISO 2898-2:2000
@ IS0
IS0 2898-2: 1997(E)
IS0 458-2:1985, Plastics - Determination of stiffness in torsion of flexible materials - Part 2: Application to
plasticized compounds of homopolymers and copolymers of vinyl chloride.
- Determination of tensile properties - Part 2: Test conditions for moulding and extrusion
I SO 527-2: 1993, Plastics
plastics.
IS0 868:1985, Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore
hardness).
IS0 1183:1987, Plastics - Methods for determining the density and relative density of non-cellular plastics.
Preparation of test specimens by machining.
IS0 2818:1994, Plastics -
Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 1:
IS0 2898-l :1996, Plastics -
Designation system and basis for specifications.
IS0 3167:1993, Plastics - Multipurpose test specimens.
IS0 3451,5:1989, Plastics - Determination of ash - Part 5: Poly(vinyl chloride).
IS0 10350: 1993, Plastics - Acquisition and presentation of comparable single-point data.
IEC 93:1980, Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials.
3 Preparation of test specimens
It is essential that specimens are always prepared by the same procedure (compression moulding), using the same
processing conditions.
The material shall be kept in moisture-proof containers until it is required for use.
3.1 Treatment of the material before moulding
Before processing, no pretreatment of the material sample is normally necessary.
3.2 Compression moulding
Before compression moulding, the material shall be plasticized using a two-roll mill under the conditions specified
in table 1.
Table 1 - Conditions for milling of material before compression moulding
Shore
Roll surface Roll nip
Roll surface
Milling time 1) Roll diameter Roll length
hardness Speed ratio
width
temperature speed
of material
m/min mm mm mm
“C min
L
approx. 5 approx. IO 1:1,2 approx. 1 e.g. 150 e.g. 300
up to A 80 130 to 160
145 to 170 approx. 5 approx. IO 1:1,2 approx. 1 e.g. 150 e.g. 300
D 35 to D 50
above D 50 160 to 175
...