SIST EN 3741:2005

Aerospace series - Nuts, clip, metric - Installation holes and assembly

This standard specifies the characteristics of the installation holes required for the utilization of clip nuts with design configuration to EN-Standards for aerospace applications.

Luft- und Raumfahrt - Klemmmuttern, metrisch - Einbaulöcher und Montage

Série aérospatiale - Écrous a pincer, métriques - Trous d'installation et montage

Aerospace series - Nuts, clip, metric - Installation holes and assembly

General Information

• Status: Published
• Publication Date: 31-May-2005
• ICS: 49.030.30 - Nuts
• Technical Committee: SS SPL - Technical Board for the general field
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jun-2005
• Due Date: 01-Jun-2005
• Completion Date: 01-Jun-2005
• Ref Project: EN 3741:2004 - Aerospace series - Nuts, clip, metric - Installation holes and assembly

Relations

• Replaces: SIST EN 3741:2004 - Aerospace series - Nuts, clip, metric - Installation holes and assembly
• Effective Date: 01-Jun-2005

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 3741:2005
01-junij-2005
1DGRPHãþD
SIST EN 3741:2004
Aerospace series - Nuts, clip, metric - Installation holes and assembly
Aerospace series - Nuts, clip, metric - Installation holes and assembly
Luft- und Raumfahrt - Klemmmuttern, metrisch - Einbaulöcher und Montage
Série aérospatiale - Écrous a pincer, métriques - Trous d'installation et montage
Ta slovenski standard je istoveten z: EN 3741:2004
ICS:
49.030.30 Matice Nuts
SIST EN 3741:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 3741:2005

---------------------- Page: 2 ----------------------

SIST EN 3741:2005
EUROPEAN STANDARD
EN 3741
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2004
ICS 49.030.30 Supersedes EN 3741:2003
English version
Aerospace series - Nuts, clip, metric - Installation holes and
assembly
Série aérospatiale - Écrous à pincer, métriques - Trous Luft- und Raumfahrt - Klemmuttern, metrisch -
d'installation et montage Einbaulöcher und Montage
This European Standard was approved by CEN on 11 September 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3741:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 3741:2005

EN 3741:2004 (E)
Contents                                                                      Page

Foreword.3
1 Scope .4
2 Normative references .4
3 Principle.4
4 Design instructions .4
4.1 Support design .4
4.1.1 Installation A: "on flank of support".4
4.1.2 Installation B: "with slot".5
4.1.3 Dimensions.5
4.2 Type of installation .5
4.2.1 Installation A .5
4.2.2 Installation B .6
5 Indication on drawings.
...