SIST EN ISO 294-1:2000/A1:2002
(Amendment)Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:1996/Amd. 1:2001)
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:1996/Amd. 1:2001)
Kunststoffe - Spritzgießen von Probekörpern aus Thermoplasten - Teil 1: Allgemeine Grundlagen und Herstellung von Vielzweckprobekörpern und Stäben (ISO 294-1:1996/Amd. 1:2001)
Plastiques - Moulage par injection des éprouvettes de matériaux thermoplastiques - Partie 1: Principes généraux, et moulage des éprouvettes a usages multiples et des barreaux (ISO 294-1:1996/Amd. 1:2001)
Polimerni materiali - Vbrizgavanje plastomernih preskušancev - 1. del: Splošna načela in oblikovanje večnamenskih in paličastih preskušancev (ISO 294-1:1996/Amd. 1:2001)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 294-1:2000/A1:2002
01-september-2002
3ROLPHUQLPDWHULDOL9EUL]JDYDQMHSODVWRPHUQLKSUHVNXãDQFHYGHO 6SORãQD
QDþHODLQREOLNRYDQMHYHþQDPHQVNLKLQSDOLþDVWLKSUHVNXãDQFHY ,62
$PG
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1:
General principles, and moulding of multipurpose and bar test specimens (ISO 294-
1:1996/Amd. 1:2001)
Kunststoffe - Spritzgießen von Probekörpern aus Thermoplasten - Teil 1: Allgemeine
Grundlagen und Herstellung von Vielzweckprobekörpern und Stäben (ISO 294-
1:1996/Amd. 1:2001)
Plastiques - Moulage par injection des éprouvettes de matériaux thermoplastiques -
Partie 1: Principes généraux, et moulage des éprouvettes a usages multiples et des
barreaux (ISO 294-1:1996/Amd. 1:2001)
Ta slovenski standard je istoveten z: EN ISO 294-1:1998/A1:2002
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 294-1:2000/A1:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 294-1:2000/A1:2002
---------------------- Page: 2 ----------------------
SIST EN ISO 294-1:2000/A1:2002
EUROPEAN STANDARD
EN ISO 294-1:1998/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2002
ICS 83.080.20
English version
Plastics - Injection moulding of test specimens of thermoplastic
materials - Part 1: General principles, and moulding of
multipurpose and bar test specimens (ISO 294-1:1996/Amd.
1:2001)
Plastiques - Moulage par injection des éprouvettes de Kunststoffe - Spritzgießen von Probekörpern aus
matériaux thermoplastiques - Partie 1: Principes généraux, Thermoplasten - Teil 1: Allgemeine Grundlagen und
et moulage des éprouvettes à usages multiples et des Herstellung von Vielzweckprobekörpern und Stäben (ISO
barreaux (ISO 294-1:1996/Amd. 1:2001) 294-1:1996/Amd. 1:2001)
This amendment A1 modifies the European Standard EN ISO 294-1:1998; it was approved by CEN on 5 January 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 294-1:1998/A1:2002 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 294-1:2000/A1:2002
EN ISO 294-1:1998/A1:2002 (E)
Foreword
The text of this Amendment EN ISO 294-1:1998/A1:2002 to the EN ISO 294-1:1998 from
Technical Committee ISO/TC 61 "Plastics" of the International Organization for
Standardization (ISO) has been taken over as an Amendment to the European Standard by
Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by September 2002, and conflicting
national standards shall be withdrawn at the latest by September 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the
United Kingdom.
Endorsement notice
The text of the Amendment to the International Standard ISO 294-1:1996/A1:2001 has been
approved by CEN as an Amendment to the European Standard without any modifications.
2
----------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.