SIST EN ISO 8675:2013
(Main)Hexagon thin nuts chamfered (style 0) with metric fine pitch thread - Product grades A and B (ISO 8675:2012)
Hexagon thin nuts chamfered (style 0) with metric fine pitch thread - Product grades A and B (ISO 8675:2012)
This International Standard specifies the characteristics of chamfered hexagon thin nuts (style 0), with metric fine pitch thread, with nominal thread diameters, D, from 8 mm up to and including 64 mm, with product grade A for sizes D ≤ 16 mm and product grade B for sizes D > 16 mm. If, in special cases, specifications other than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 724, ISO 898-2, ISO 965-1, ISO 3506-2 and ISO 4759-1.
Niedrige Sechskantmuttern mit Fase (Typ 0) mit metrischem Feingewinde - Produktklassen A und B (ISO 8675:2012)
Diese Internationale Norm legt Eigenschaften von niedrigen Sechskantmuttern (mit Fase) mit metrischem Feingewinde mit Gewindenenndurchmessern D von 8 mm bis 64 mm fest. Für die Gewindenenndurchmesser D 16 mm gilt Produktklasse A und für die Gewindenenndurchmesser D 16 mm Produktklasse B.
Falls in besonderen Fällen andere Festlegungen als die in dieser Internationalen Norm aufgeführten benötigt werden, können diese den entsprechenden Internationalen Normen entnommen werden, z. B. ISO 724, ISO 898 2, ISO 965 1, ISO 3506 2 und ISO 4759 1.
Sechskantmuttern mit Regelgewinde nach ISO 4035 sollten bevorzugt werden.
Écrous bas hexagonaux chanfreinés (style 0) à filetage métrique à pas fin - Grades A et B (ISO 8675:2012)
L'ISO 8675:2012 spécifie les caractéristiques des écrous bas hexagonaux chanfreinés (style 0) à filetage métrique à pas fin, de diamètre nominal de filetage, D, de 8 mm à 64 mm inclus, de grade A pour les filetages D £ 16 mm et de grade B pour les filetages D > 16 mm.
Šestrobe nizke matice s posnetjem (tip 0) z metrskim drobnim navojem - Razreda izdelave A in B (ISO 8675:2012)
Ta mednarodni standard določa značilnosti šestrobih nizkih matic s posnetjem (tip 0) z metrskim drobnim navojem z nazivnimi premeri navoja od 8 mm do vključno 64 mm, z razredom izdelave A za velikosti premera ≤ 16 mm in razredom izdelave B za velikosti premera > 16 mm. Če so v posebnih primerih zahtevane specifikacije, ki niso navedene v tem mednarodnem standardu, jih je mogoče izbrati iz obstoječih mednarodnih standardov, na primer standardov ISO 724, ISO 898-2, ISO 965-1, ISO 3506-2 in ISO 4759-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8675:2013
01-maj-2013
1DGRPHãþD
SIST EN ISO 8675:2002
Šestrobe nizke matice s posnetjem (tip 0) z metrskim drobnim navojem - Razreda
izdelave A in B (ISO 8675:2012)
Hexagon thin nuts chamfered (style 0) with metric fine pitch thread - Product grades A
and B (ISO 8675:2012)
Niedrige Sechskantmuttern mit Fase (Typ 0) mit metrischem Feingewinde -
Produktklassen A und B (ISO 8675:2012)
Écrous bas hexagonaux chanfreinés (style 0) à filetage métrique à pas fin - Grades A et
B (ISO 8675:2012)
Ta slovenski standard je istoveten z: EN ISO 8675:2012
ICS:
21.040.10 Metrski navoji Metric screw threads
21.060.20 Matice Nuts
SIST EN ISO 8675:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8675:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 8675:2013
EUROPEAN STANDARD
EN ISO 8675
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2012
ICS 21.060.20 Supersedes EN ISO 8675:2000
English Version
Hexagon thin nuts chamfered (style 0) with metric fine pitch
thread - Product grades A and B (ISO 8675:2012)
Écrous bas hexagonaux chanfreinés (style 0) à filetage Niedrige Sechskantmuttern (mit Fase) mit metrischem
métrique à pas fin - Grades A et B (ISO 8675:2012) Feingewinde - Produktklassen A und B (ISO 8675:2012)
This European Standard was approved by CEN on 13 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8675:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8675:2013
EN ISO 8675:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8675:2013
EN ISO 8675:2012 (E)
Foreword
This document (EN ISO 8675:2012) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at
the latest by June 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8675:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8675:2012 has been approved by CEN as a EN ISO 8675:2012 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8675:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 8675:2013
INTERNATIONAL ISO
STANDARD 8675
Third edition
2012-12-15
Hexagon thin nuts chamfered (style 0)
with metric fine pitch thread — Product
grades A and B
Écrous bas hexagona
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.