SIST EN 4702-05:2018
(Main)Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 05: Retaining washer
Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 05: Retaining washer
The standard specifies the dimensions, mass tolerances of quick-release and locking – washers for use in fuselage interior equipment and non-structural or secondary structural area.
Luft- und Raumfahrt - Schnellverschlusssysteme für nicht-strukturelle und Innenausstattungsanwendungen - Teil 05: Haltescheibe
Série aérospatiale - Fixations rapides filetées pour applications non-structurales et revêtements intérieurs - Partie 05: Rondelle de maintiene
La présente norme européenne décrit les dimensions et les tolérances de masse des rondelles à démontage et à verrouillage rapide pour une utilisation dans les équipements à l'intérieur du fuselage et dans les zones non-structurales ou les zones structurales secondaires destinée aux applications aéronautiques.
Aeronavtika - Spončni sistemi za hitro sprostitev za nestrukturno uporabo in notranje obloge - 05. del: Zadrževalna podložka
Ta standard določa dimenzije in masne tolerance podložk za hitro sproščanje in zapiranje ter za uporabo v notranji opremi v trupu letala ter nestrukturnem ali sekundarnem strukturnem območju.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Schnellverschlusssysteme für nicht-strukturelle und Innenausstattungsanwendungen - Teil 05: HaltescheibeSérie aérospatiale - Fixations rapides filetées pour applications non-structurales et revêtements intérieurs - Partie 05: Rondelle de maintieneAerospace series - Quick release fastening systems for non-structural and lining applications - Part 05: Retaining washer49.030.50Podložke in drugi blokirni elementiWashers and other locking elementsICS:Ta slovenski standard je istoveten z:EN 4702-05:2017SIST EN 4702-05:2018en,fr,de01-januar-2018SIST EN 4702-05:2018SLOVENSKI
STANDARD
SIST EN 4702-05:2018
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4702-05
October
t r s y ICS
v {ä r u w English Version
Aerospace series æ Quick release fastening systems for nonæstructural and lining applications æ Part
r wã Retaining washer Série aérospatiale æ Fixations rapides filetées pour applications nonæstructurales et revêtements intérieurs æ Partie
r w ã Rondelle de maintiene
Luftæ und Raumfahrt æ Schnellverschlusssysteme für nichtæstrukturelle und Innenausstattungsanwendungen æ Teil
r wã Haltescheibe This European Standard was approved by CEN on
t u July
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
v y r tæ r wã t r s y ESIST EN 4702-05:2018
EN 4702-05:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Requirements . 5 3.1 Configuration, dimensions, tolerances and mass . 5 3.2 Material and surface treatment . 6 3.3 Colour . 7 4 Designation. 7 5 Marking . 7 6 Quality assurance . 7 6.1 Supplier certification . 7 6.2 Product qualification . 7 7 Technical Specification . 8 Annex A (normative)
Material . 9 Bibliography . 11
SIST EN 4702-05:2018
EN 4702-05:2017 (E) 3 European foreword This document (EN 4702-05:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this European Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be withdrawn at the latest by April 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 4702-05:2018
EN 4702-05:2017 (E) 4 1 Scope The standard specifies the dimensions, mass tolerances of quick-release and locking – washers for use in fuselage interior equipment and non-structural or secondary structural area. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series — Marking of aerospace products EN 4710-01, Aerospace series — Quick release fastening systems for non-structural applications — Part 01: Technical specification EN 10088-2, Stainless steels — Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 22768-1:1993, General tolerances — Part 1: Tolerances for
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.