SIST EN ISO 10423:2005
(Main)Petroleum and natural gas industries - Drilling and production equipment - Wellhead and christmas tree equipment (ISO 10423:2003)
Petroleum and natural gas industries - Drilling and production equipment - Wellhead and christmas tree equipment (ISO 10423:2003)
Urgent withdrawal of EN ISO 10423:2001 by BT and decision to process the revision under special conditions => no German translation will be provided, start of UAP is brought forward to 2004-03-04 should no BT Member comment negatively before 2004-02-27. UAP of 3 months, closing on 2004-06-04.
ISO 10423:2001 was revised in 2003. Note for the Editor - Title shall read "(ISO 10423:2003)" (mht 2004-07-26)
Erdöl- und Erdgasindustrie - Bohr- und Förderausrüstung - Bohrlochkopf- und Eruptionskreuz-Ausrustung (ISO 10423:2003)
Indutries du pétrole et du gaz naturel - Equipement de forage et de production - Equipement pour tetes de puits et arbre de Noël (ISO 10423:2003)
Petroleum and natural gas industries - Drilling and production equipment - Wellhead and christmas tree equipment (ISO 10423:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10423:2005
01-marec-2005
Petroleum and natural gas industries - Drilling and production equipment -
Wellhead and christmas tree equipment (ISO 10423:2003)
Petroleum and natural gas industries - Drilling and production equipment - Wellhead and
christmas tree equipment (ISO 10423:2003)
Erdöl- und Erdgasindustrie - Bohr- und Förderausrüstung - Bohrlochkopf- und
Eruptionskreuz-Ausrustung (ISO 10423:2003)
Indutries du pétrole et du gaz naturel - Equipement de forage et de production -
Equipement pour tetes de puits et arbre de Noël (ISO 10423:2003)
Ta slovenski standard je istoveten z: EN ISO 10423:2004
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
SIST EN ISO 10423:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10423:2005
---------------------- Page: 2 ----------------------
SIST EN ISO 10423:2005
EUROPEAN STANDARD
EN ISO 10423
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2004
ICS 75.180.10 Supersedes EN ISO 10423:2001
English version
Petroleum and natural gas industries - Drilling and production
equipment - Wellhead and christmas tree equipment (ISO
10423:2003)
Indutries du pétrole et du gaz naturel - Equipement de Erdöl- und Erdgasindustrie - Bohr- und Förderausrüstung -
forage et de production - Equipement pour têtes de puits et Bohrlochkopf- und Eruptionskreuz-Ausrustung (ISO
arbre de Noël (ISO 10423:2003) 10423:2003)
This European Standard was approved by CEN on 8 August 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10423:2004: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10423:2005
EN ISO 10423:2004 (E)
Foreword
The text of ISO 10423:2003 has been prepared by Technical Committee ISO/TC 67 "Materials,
equipment and offshore structures for petroleum and natural gas industries” of the International
Organization for Standardization (ISO) and has been taken over as EN ISO 10423:2004 by
Technical Committee CEN/TC 12 "Materials, equipment and offshore structures for petroleum,
petrochemical and natural gas industries", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2005, and conflicting national
standards shall be withdrawn at the latest by March 2005.
This document supersedes EN ISO 10423:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 10423:2003 has been approved by CEN as EN ISO 10423:2004 without any
modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10423:2005
EN ISO 10423:2004 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 13628-4 1999 Petroleum and natural gas EN ISO 13628-4 1999
industries - Design and operation of
subsea production systems - Part 4:
Subsea wellhead and tree
equipment
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10423:2005
---------------------- Page: 6 ----------------------
SIST EN ISO 10423:2005
INTERNATIONAL ISO
STANDARD 10423
Third edition
2003-12-15
Petroleum and natural gas industries —
Drilling and production equipment —
Wellhead and christmas tree equipment
Industries du pétrole et du gaz naturel — Équipement de forage et de
production — Équipement pour têtes de puits et arbre de Noël
Reference number
ISO 10423:2003(E)
©
ISO 2003
---------------------- Page: 7 ----------------------
SIST EN ISO 10423:2005
ISO 10423:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10423:2005
ISO 10423:2003(E)
Contents Page
Foreword . vi
Introduction. vii
1 Scope. 1
1.1 Purpose. 1
1.2 Applicability. 1
1.3 Service conditions. 2
1.4 Product specification levels (PSL) . 3
2 Normative references. 6
3 Terms, definitions and abbreviated terms. 8
3.1 Terms and definitions. 8
3.2 Abbreviated terms. 20
4 Design and performance — General requirements . 21
4.1 Performance requirements — General . 21
4.2 Service conditions. 21
4.3 Design methods. 23
4.4 Miscellaneous design information . 27
4.5 Design documentation. 28
4.6 Design review. 28
4.7 Design verification. 28
5 Materials — General requirements. 28
5.1 General. 28
5.2 Written specifications. 28
5.3 Mandrel tubing and casing hangers. 29
5.4 Bodies, bonnets, end and outlet connections . 32
5.5 Ring gaskets. 39
5.6 Test coupons (TC). 40
5.7 Qualification test coupons (QTC). 43
5.8 Heat-treating equipment qualification. 46
5.9 Material qualification. 46
5.10 Bullplugs and valve-removal plugs. 46
5.11 Back-pressure valves. 46
5.12 Pressure-boundary penetrations. 46
5.13 Wear bushings. 46
5.14 Hub-end connectors. 46
6 Welding — General requirements . 47
6.1 General. 47
6.2 Non-pressure-containing weldments other than weld overlays (PSL 1 to PSL 3) . 47
6.3 Pressure-containing fabrication weldments for bodies, bonnets, end and outlet connections,
bullplugs, valve-removal plugs and back-pressure valves . 47
6.4 Pressure-containing repair weldments for bodies, bonnets, end and outlet connections,
bullplugs, valve-removal plugs and back-pressure valves . 52
6.5 Weld overlay for corrosion resistance and/or hard facing and other material surface property
controls . 54
© ISO 2003 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10423:2005
ISO 10423:2003(E)
7 Quality control. 57
7.1 General. 57
7.2 Measuring and testing equipment. 57
7.3 QuaIity control personnel qualifications . 58
7.4 Quality control requirements. 58
7.5 Quality control records requirements. 95
8 Equipment marking. 100
8.1 Marking requirements. 100
8.2 Wellhead equipment. 102
8.3 Connectors and fittings. 102
8.4 Casing and tubing hangers . 102
8.5 Valves and chokes. 103
8.6 Loose connectors [flanged, threaded, other end connectors (OEC) and welded]. 104
8.7 Other equipment. 104
8.8 Studs and nuts. 105
8.9 Christmas trees. 105
8.10 Valve-removal plugs. 105
8.11 Bullplugs. 105
8.12 Back-pressure valves. 106
9 Storing and shipping. 106
9.1 Draining after testing. 106
9.2 Rust prevention. 106
9.3 Sealing surface protection . 106
9.4 Assembly and maintenance instructions . 106
9.5 Ring gaskets. 106
9.6 Age control of non-metallic materials. 106
10 Equipment-specific requirements. 107
10.1 Flanged end and outlet connections. 107
10.2 Threaded end and outlet connections . 140
10.3 Studs and nuts. 146
10.4 Ring gaskets. 148
10.5 Valves. 154
10.6 Casing and tubing heads. 169
10.7 Casing and tubing hangers . 174
10.8 Tubing-head adapters. 179
10.9 Chokes. 181
10.10 Tees and crosses . 184
10.11 Test and gauge connections for 103,5 MPa and 138,0 MPa (15 000 psi and 20 000 psi)
equipment . 189
10.12 Fluid sampling devices. 189
10.13 Christmas trees. 192
10.14 Cross-over connectors. 192
10.15 Adapter and spacer spools . 197
10.16 Actuators. 198
10.17 Lock screws, alignment pins and retainer screw packing mechanisms. 202
10.18 Other end connectors (OECs). 203
10.19 Top connectors. 204
10.20 Surface and underwater safety valves and actuators . 205
10.21 Bullplugs. 210
10.22 Valve-removal plugs. 213
10.23 Other pressure-boundary penetrations . 213
10.24 Back-pressure valves. 214
11 Repair and remanufacture. 214
iv © ISO 2003 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 10423:2005
ISO 10423:2003(E)
Annex A (informative) Purchasing guidelines . 215
Annex B (informative) US Customary unit tables and data for this International Standard . 234
Annex C (informative) Method of calculating stud bolt lengths for type 6B and 6BX flanges . 289
Annex D (informative) Recommended flange bolt torque . 291
Annex E (informative) Recommended weld groove design dimensions . 295
Annex F (informative) Performance verification procedures . 299
Annex G (informative) Design and rating of equipment for use at elevated temperatures . 333
Annex H (normative) Design and manufacture of surface wellhead running, retrieving and testing
tools, clean-out tools and wear bushings . 336
Annex I (normative) Performance verification procedures for surface safety valves and underwater
safety valves . 340
Annex J (normative) Repair and remanufacture requirements . 348
Annex K (informative) Recommended specifications for top connectors for christmas trees . 361
Annex L (normative) Specifications for valve-removal preparations and valve-removal plugs . 376
Annex M (informative) List of tables and figures. 391
Bibliography. 401
© ISO 2003 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 10423:2005
ISO 10423:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10423 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for
petroleum, petrochemical and natural gas industries, Subcommittee SC 4, Drilling and production equipment.
This third edition cancels and replaces the second edition (ISO 10423:2001), of which it constitutes a minor
revision. Details of the differences between this third edition and the second edition may be obtained, upon
request, from ISO/TC 67/SC 4.
vi © ISO 2003 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 10423:2005
ISO 10423:2003(E)
Introduction
This International Standard is based on API Spec 6A, seventeenth edition, February 1996, its errata and
supplement, and API Spec 6AV1, first edition, February 1996.
The contents of API Spec 14D (upon which ISO 10433 was based) and API Recommended Practice 14H (upon
which ISO 10419 was based) have been incorporated in API Spec 6A, seventeenth edition.
The International System of units (SI) is used in this International Standard. However, nominal sizes are shown as
fractions in the inch system.
The fractions and their decimal equivalents are equal and interchangeable. Metric conversions and inch
dimensions in this International Standard are based on the original fractional inch designs. Functional dimensions
have been converted into the metric system to ensure interchangeability of products manufactured in metric or inch
systems (see also Annex B).
Tables referenced in the main body of this International Standard which are marked with an asterisk are repeated
in Annex B in US Customary units with the same table number as in the main body but with the prefix B. In figures
where dimensions are only given in inches, the values of surface roughness have been indicated in accordance
with US draughting conventions. See also Annex M for listings of tables and figures.
Users of this International Standard should be aware that further or differing requirements may be needed for
individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser
from accepting, alternative equipment or engineering solutions for the individual application. This may be
particularly applicable where there is innovative or developing technology. Where an alternative is offered, the
vendor should identify any variations from this International Standard and provide details.
© ISO 2003 – All rights reserved vii
---------------------- Page: 13 ----------------------
SIST EN ISO 10423:2005
---------------------- Page: 14 ----------------------
SIST EN ISO 10423:2005
INTERNATIONAL STANDARD ISO 10423:2003(E)
Petroleum and natural gas industries — Drilling and production
equipment — Wellhead and christmas tree equipment
1 Scope
1.1 Purpose
This International Standard specifies requirements and gives recommendations for the performance, dimensional
and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing,
shipment, purchasing, repair and remanufacture of wellhead and christmas tree equipment for use in the petroleum
and natural gas industries.
This International Standard does not apply to field use, field testing or field repair of wellhead and christmas tree
equipment.
1.2 Applicability
This International Standard is applicable to the following specific equipment.
a) Wellhead equipment:
casing head housings;
casing head spools;
tubing head spools;
cross-over spools;
multi-stage head housings and spools.
b) Connectors and fittings:
cross-over connectors;
tubing head ad
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.