SIST HD 478.2.7 S1:2003
(Main)Classification of environmental conditions -- Part 2: Environmental conditions appearing in nature -- Fauna and flora
Classification of environmental conditions -- Part 2: Environmental conditions appearing in nature -- Fauna and flora
Describes influences from fauna and flora to which products are liable to be exposed during storage, transportation and use.
Klassifizierung von Umweltbedingungen -- Teil 2: Natürliche Einflüsse -- Fauna und Flora
Classification des conditions d'environnement -- Partie 2: Conditions d'environnement présentes dans la nature -- Faune et flore
Décrit les influences de la faune et de la flore, auxquelles les produits sont susceptibles d'être exposés pendant leur stockage, leur transport et leur utilisation.
Classification of environmental conditions - Part 2: Environmental conditions appearing in nature - Fauna and flora
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST HD 478.2.7 S1:2003
STANDARD
julij 2003
Classification of environmental conditions - Part 2: Environmental conditions
appearing in nature - Fauna and flora
ICS 19.040 Referenčna številka
SIST HD 478.2
...
This May Also Interest You
The present document defines classes of environmental conditions and their severities to which telecommunication equipment may be exposed. The severities specified are those which will have a low probability of being exceeded; generally less than 1 %. The present document applies to equipment during portable and non-stationary use including periods of transfer, down time, maintenance and repair at locations defined in clauses 3 to 5.
- Standard15 pagesEnglish languagesale 10% offe-Library read for×1 day
The present document contains requirements for:
- the output performance of the direct current (dc) power equipment at the interface "A";
- the input of the telecommunications equipment connected to interface "A" powered by dc.
The dc voltage at interface "A" may be derived from the AC primary supply. The dc supply may incorporate a backup battery. If any other equipment e.g. datacom equipment, are connected to interface "A" in parallel to telecommunications equipment, all requirements addressed in clause 4 of the present document must be fulfilled. The present document aims at providing compatibility between the power supply equipment and the power consuming telecommunications equipment, and also between different system blocks connected to the same power supply.
NOTE 1: The present document is applicable only to -48 V dc power supply interfaces. However, during a transitional period, other dc voltages may be used in existing installations. Annex A gives guidance on working in conjunction with existing -60 V dc supply systems.
The power supply interface, interface "A", is a physical point to which all the requirements are related (see figure 1).
This point is situated between the power supply system(s) and the power consuming telecommunications equipment.
NOTE 2: Interface "A" is located at the power terminals of the telecommunications equipment. Subject to the installation preconditions this point may be located at any other point between the power supply system and the telecommunications equipment by mutual agreement of the relevant parties.
The requirements at interface "A" apply to:
- the output of the power supply equipment or power supply installation of telecommunications centres;
- the power supply input of telecommunications equipment installed at telecommunication centres;
- telecommunications equipment, installed in customers' premises, whose dc interface "A" is also used by equipment requiring a supply to this specification.
NOTE 3: Normally there is more than one load unit connected to interface "A". In these cases, interface "A" will undergo further restrictions with respect to noise limits or other disturbances specified in clause 4.8.
NOTE 4: Disturbances on the power supply interface "A" relating to the continuous wave phenomena below 20 kHz are covered within the present document.
NOTE 5: An example of a configuration in which interface "A" is identified is given in annex D.
- Standard23 pagesEnglish languagesale 10% offe-Library read for×1 day
The present document specifies test methods and severities for the verification of the required resistibility of telecommunication equipment according to the relevant environmental class. The tests in the present document apply to the use of equipment installed permanently or temporarily in ground vehicles and cover the vehicles and the environmental conditions stated in ETS 300 019-1-5 [1]. The tests cover installations in vehicles powered by electric motors and combustion engines. Applications in combustion engine compartments are excluded.
- Standard16 pagesEnglish languagesale 10% offe-Library read for×1 day
The present document specifies test methods and severities for the verification of the required resistibility of telecommunication equipment according to the relevant environmental class. The tests defined in the present document apply to portable and non-stationary use of equipment, covering the environments stated in EN 300 019-1-7 [1].
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
The present document applies in telecommunication centres and similar installations to the bonding network of the building, the bonding network of the equipment, and the interconnection between these two networks. It contributes to the standardization of telecommunication and datacom equipment installation.
It also co-ordinates with the pre-conditions of the installation to achieve the following targets:
- safety from electrical hazards;
- reliable signal reference;
- satisfactory Electromagnetic Compatibility (EMC) performance.
A defined bonding configuration down to the equipment level shall facilitate the installation, operation and maintenance of telecommunication centres in telecommunication buildings or similar installations independent of the equipment supplier. The specification of telecommunication and datacom equipment and of the pre-conditions of installation are subject to agreement of the parties (e.g. the supplier and the purchaser). Annex A can be used in the procedure to achieve agreement.
The present document does not cover safety and EMC aspects of the equipment. Those aspects are covered by other relevant standards. The present document does not apply to the installation of telecommunication and datacom equipment in locations other than telecommunication centres, e.g.:
- smaller telecommunication equipment inside a subscriber's building;
- subscriber line terminal equipment.
NOTE: Earthing and bonding of equipment installed in locations other than telecommunication building is covered by EN 50310 [8].
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
The present document specifies test severities and methods for verification of the required resistibility of equipment according to the relevant environmental class. The tests defined in Part 2-1 of this multi-part standard apply to storage of equipment covering the environmental conditions stated in ETS 300 019-1-1 [1].
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
The present document specifies test severities and methods for the verification of the required resistibility of equipment according to the relevant environmental class. The tests in Part 2-3 of this multi-part EN apply to stationary use of equipment at weatherprotected locations covering the environmental conditions stated in EN 300 019-1-3 [1].
- Standard31 pagesEnglish languagesale 10% offe-Library read for×1 day
The present document contains requirements for:
• the output performance of the power equipment at the interface A3;
• the input of the telecommunications equipment connected to interface A3.
The voltage at interface A3 may be the ac mains, a rectified voltage derived from ac three phase mains, a rectified voltage derived from ac single phase mains or a low voltage derived from a battery. The power supply equipment may incorporate a backup battery.
The present document aims at providing compatibility between the power supply equipment and both the telecommunications equipment, and the different load units connected to the same interface A3 (e.g. datacom equipment).
The requirements at interface A3 apply to:
• the output of the power supply equipment or power supply installation of telecommunications centres;
• the power supply input of telecommunications equipment and the datacom equipment installed at telecommunications centres;
• telecommunications equipment and the datacom equipment, installed in customer's premises, whose power interface A3 is also used by equipment requiring a supply to the present document. The purpose of the present document is:
• to identify a power supply system with the same characteristics for all telecommunications and data communication equipment defined in the area of application;
• to facilitate interworking of different (types of) loads units;
• to facilitate the standardization of power supply systems for telecommunications and datacom equipment;
• to facilitate the installation, operation and maintenance in the same network of equipment and telecommunications and datacom systems from different origins.
- Standard18 pagesEnglish languagesale 10% offe-Library read for×1 day
The present document defines classes of environmental conditions and their severities to which telecommunication equipment may be exposed. The severities specified are those which will have a low probability of being exceeded; generally less than 1 %. The present document applies to equipment designed principally for maritime use. Conditions of use vary significantly in relation to the size of the vessel and the function for which it was designed. The reader should ensure that the relevant classes are chosen to suit this particular application. The present document covers the following types of vessel:
- vessel propelled by mechanical means, including offshore units;
- vessel not propelled by mechanical means, including sailing boats and life rafts.
The classes defined apply to all sizes of vessel from pleasure craft to trawlers, ferry boats, icebreakers and cargo ships including tankers.
- Standard12 pagesEnglish languagesale 10% offe-Library read for×1 day
The present document defines the classes of environmental conditions and their severities to which telecommunications equipment may be exposed. The severities specified are those which will have a low probability of being exceeded; generally less than 1 %. The present document applies to equipment installed for stationary use at underground locations during:
- normal operation;
- on site installation and lining up;
- repair, maintenance and restoration of functions failed.
- Standard11 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.