SIST ENV 197-2:2000
(Main)Cement - Part 2: Conformity evaluation
- BACK
- 31-Aug-2000
- 30-Nov-2001
- 91.100.10
- 89/106/EEC
- CAA
Cement - Part 2: Conformity evaluation
This European Pre-standard describes the scheme for the evaluation of conformityof cement complying with the requirements of ENV 197-1. NOTE: During the pre-standard stage this document is intended to assist in the convergence of existing national schemes for conformity evaluation.
Zement - Teil 2: Bewertung der Konformität
Ciment - Partie 2: Evaluation de la conformité
Cement - 2. del: Ovrednotenje skladnosti
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ENV 197-2:
01-DYJXVW
Cement - 2. del: Ovrednotenje skladnosti
Cement - Part 2: Conformity evaluation
Zement - Teil 2: Bewertung der Konformität
Ciment - Partie 2: Evaluation de la conformité
Ta slovenski standard je istoveten z: ENV 19
...
This May Also Interest You
The general scope of the core product category rules (PCR) is given in EN 15804:2012+A2:2019, Clause 1.
This PCR is primarily intended for the creation of cradle-to-gate EPDs of cement and building lime.
In other respects, the scope is as in EN 15804:2012+A2:2019.
- Standard27 pagesEnglish languagesale 10% offe-Library read for×1 day
This document describes the test methods for all building limes covered by EN 459-1.
This document specifies in Table 2 the methods used for the chemical analyses and the determination of physical properties of building limes.
This document describes primary methods of chemical analyses. The reference methods and, in certain cases, alternative methods in this document can be considered to be equivalent.
- Standard74 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft72 pagesEnglish languagesale 10% offe-Library read for×1 day
This document deals with Portland-composite cement CEM II-C/M, not covered by EN 197-1, and a new type of Composite cement CEM VI, also not covered by EN 197-1, whose intended use is the preparation of concrete, mortar, grout etc.
This document does not cover:
- common cement covered by EN 197-1;
- very low heat special cement covered by EN 14216;
- supersulfated cement covered by EN 15743;
- calcium aluminate cement covered by EN 14647;
- masonry cement covered by EN 413-1.
- Standard10 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft10 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the scheme for the assessment and verification of constancy of performance (AVCP) of cements to their corresponding product specification standards, including certification of constancy of performance by a product certification body.
The standard provides technical rules for factory production control by the manufacturer, including autocontrol testing of samples, and for the tasks of the product certification body. It also provides rules for actions to be followed in the event of non-conformity, the procedure for the AVCP and requirements for dispatching centres.
In this European Standard, the word “cement” is used to refer both to common cements as defined in EN 197 1 and to other cements and binders for which the relevant product specification standard makes reference to this European Standard and which are submitted for certification. Such a cement is produced at a given factory and belongs to a particular type and a particular strength class, as defined and specified in the relevant product specification standard.
The guidelines given in the Technical Report CEN/TR 14245 [1] ) should be used for the application of this European Standard.
This European Standard should be linked with Annexes ZA of European Standards covering cements and binders, i.e. EN 197 1, EN 14216, EN 14647, EN 413 1, EN 15743, in particular for the assignments of tasks to the manufacturer and to the product certification body.
NOTE The reason for having drafted this separate document is that the provisions it includes are applicable to different products covered by different European Standards.
Guidance
EN 197-2 deals with the evaluation of conformity of cements and binders that are submitted for certification. It deals in particular with cases where “further testing” of the product is undertaken, as is the case for attestation system 1+ under the Construction Products Regulation. The products for which EN 197-2 is applicable are: the common cement products and the low heat cements and the sulfate resisting cements, refer to EN 197-1, the very low heat special cements, refer to EN 14216, the supersulfated cements, refer to EN 15743, the calcium aluminate cements, refer to EN 14647, and the masonry cements, refer to EN 413 1.
- Technical report40 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft41 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies the scheme for the assessment and verification of constancy of performance (AVCP) of cements, including certification of constancy of performance.
The document provides technical rules for factory production control, further testing of samples taken at the manufacturing plant (autocontrol testing) and assessment of the performance of the cement, initial inspection of the manufacturing plant and of factory production control, continuing surveillance, assessment and evaluation of factory production control and audit-testing of samples. It also provides rules for actions to be followed in the event of non-conformity and requirements for dispatching centres and for depots.
In this document, the word "cement" is used to refer both to common cements as defined in EN 197-1 and to other cements and binders for which the relevant product specification standard makes reference to this document and which are submitted for certification. Such a cement is produced at a given factory and belongs to a particular type and a particular strength class, as defined and specified in the relevant product specification standard.
The guidelines given in the Technical Report CEN/TR 14245 [4] contain information for the application of this document.
NOTE The reason for having drafted this separate document is that the provisions it includes are applicable to different products covered by different European Standards.
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft24 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies a method for determining the flexural and compressive strength of moulded mortar specimens.
- Standard15 pagesEnglish languagesale 10% offe-Library read for×1 day
This document describes the analytical procedures used to determine the content of C3A in the clinker starting from a chemical analysis on cement. The method can be applied to CEM type I and IV for the determination of the requirement of C3A, as defined on EN 197-1.
This document describes two methods, traditional wet and XRF analysis (EN 196-2), which can be considered to be equivalent, in the scope of this CEN/TR 17365, for the determination of Al2O3, Fe2O3 and SO3.
The same methods are described in EN 196-2, but for the scope of this document, the X-ray fluorescence (XRF) is the preferred method to be used for the determination of Al2O3, Fe2O3 and SO3.
- Technical report19 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft20 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard describes the test methods for binders for floor screeds based on calcium sulphate specified in prEN 13454 1.
This European Standard describes the test methods for factory made mixtures for floor screeds based on calcium sulphate specified in EN 13813.
This European Standard describes reference test methods. If other than these methods and conditions are used, it is necessary to show that they give results equivalent to those given by the reference methods. In the event of a dispute, only the reference test method is used.
- Standard22 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard describes three methods of determining the fineness of cement.
The sieving method serves only to demonstrate the presence of coarse cement particles. This method is primarily suited to checking and controlling the production process.
The air-jet sieving method measures the retention on sieving and is suitable for particles which substantially pass a 2,0 mm test sieve. It may be used to determine the particle size distribution of agglomerates of very fine particles. This method may be used with test sieves in a range of aperture sizes, e.g. 63 μm and 90 μm.
The air permeability method (Blaine) measures the specific surface area (mass related surface area) by comparison with a reference material sample. The determination of the specific surface area serves primarily to check the consistency of the grinding process of one and the same plant. This method only enables a limited assessment of the properties of the cement in use.
NOTE The air permeability method may not give significant results for cements containing ultrafine materials.
The methods are applicable to all the cements defined in EN 197.
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies the apparatus and procedure for determining the heat of hydration of cements and other hydraulic binders at different test ages by isothermal conduction calorimetry.
This test procedure is intended for measuring the heat of hydration of cement up to 7 days in order to obtain data homogeneous with EN 196 8. Nevertheless this test duration may be critical for some apparatus, even if they can work properly at shorter test ages.
Contrary to EN 196 8 (solution method) this method gives the heat of hydration continuously over the time. Additionally, the heat flow versus time is given.
- Standard17 pagesEnglish languagesale 10% offe-Library read for×1 day
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.