SIST EN 302 617 V2.3.1:2018
(Main)Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation - Harmonised Standard for access to radio spectrum
Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation - Harmonised Standard for access to radio spectrum
The present document specifies technical characteristics and methods of measurements for DSB AM ground based
transmitters, receivers and transceivers operating in all or any part of the aeronautical frequency band between
225 MHz and 399,975 MHz.
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.1] is given in annex A.
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Directive 2014/53/EU [i.1] as well as essential requirements under the Single
European Sky (SES) Interoperability Regulation No 552/2004 [i.3] and related implementing rules and/or essential
requirements under the EASA basic Regulation No 216/2008 [i.5] as amended by Regulation No 1108/2009 [i.6] may
apply to equipment within the scope of the present document.
Talni UHF-radijski oddajniki, sprejemniki in sprejemniki-oddajniki za UHF-letalsko mobilno storitev, ki uporablja amplitudno modulacijo - Harmonizirani standard za dostop do radijskega spektra
Ta dokument določa tehnične lastnosti in metode merjenja za talne oddajnike DSB AM, sprejemnike in sprejemnike-oddajnike, ki delujejo v celotnem aeronavtičnem frekvenčnem pasu med 225 MHz in 399,975 MHz ali kateremkoli njegovem delu.
OPOMBA: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.2 Direktive 2014/53/EU [i.1] je podano v dodatku A.
Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta lahko uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov 3. člena Direktive 2014/53/EU [i.1], in tudi bistvene zahteve iz Uredbe o interoperabilnosti enotnega evropskega neba 552/2004 [i.5] ter zadevna izvedbena pravila in/ali bistvene zahteve iz osnovne Uredbe EASA št. 216/2008 [i.5], kakor je bila spremenjena z Uredbo št. 1108/2009 [i.6].
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Talni UHF-radijski oddajniki, sprejemniki in sprejemniki-oddajniki za UHF-letalsko mobilno storitev, ki uporablja amplitudno modulacijo - Harmonizirani standard za dostop do radijskega spektraGround-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation - Harmonised Standard for access to radio spectrum49.090On-board equipment and instruments33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 302 617 V2.3.1 (2018-07)SIST EN 302 617 V2.3.1:2018en01-oktober-2018SIST EN 302 617 V2.3.1:2018SLOVENSKI
STANDARD
SIST EN 302 617 V2.3.1:2018
ETSI EN 302 617 V2.3.1 (2018-07) Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation; Harmonised Standard for access to radio spectrum
HARMONISED EUROPEAN STANDARD SIST EN 302 617 V2.3.1:2018
ETSI ETSI EN 302 617 V2.3.1 (2018-07) 2
Reference REN/ERM-TGAERO-61 Keywords aeronautical, AM, DSB, harmonised standard, radio, testing, UHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETM are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM® and the GSM logo are trademarks registered and owned by the GSM Association. SIST EN 302 617 V2.3.1:2018
ETSI ETSI EN 302 617 V2.3.1 (2018-07) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 7 3 Definitions and abbreviations . 8 3.1 Definitions . 8 3.2 Abbreviations . 8 4 General requirements . 9 4.1 Frequency control . 9 4.2 Controls and indicators . 9 4.3 Class of emission and modulation characteristics . 9 4.4 Warm up . 9 4.5 Protection of the transmitter . 9 4.5.1 Definition . 9 4.5.2 Method of measurement . 9 4.5.3 Requirement . 10 5 General conditions of measurement . 10 5.1 Transmitter test signal arrangement . 10 5.1.1 Coaxial termination. 10 5.1.2 Signal sources . 10 5.1.3 Normal test signal . 10 5.2 Receiver test signal arrangement . 10 5.2.1 Test signal sources . 10 5.2.2 Nominal frequency . 10 5.2.3 Normal test signal . 10 5.2.4 Squelch . 10 5.2.5 Normal audio output power . 10 5.2.6 Audio AGC . 10 5.3 Test channels . 11 5.4 Environmental profile . 11 5.5 Test power source . 11 5.6 Normal test conditions . 11 5.6.1 Normal temperature and humidity . 11 5.6.2 Normal power sources . 11 5.6.2.1 Mains voltage and frequency . 11 5.6.2.2 Other power sources . 11 5.7 Extreme test conditions . 12 5.7.1 Extreme temperatures . 12 5.7.2 Extreme values of test power sources . 12 5.7.2.1 Mains voltage . 12 5.7.2.2 Other power sources . 12 5.8 Performance test . 12 5.9 Environmental tests . 12 5.9.1 General . 12 5.9.2 Procedure for tests at extreme temperatures . 13 5.9.3 Temperature tests . 13 5.9.3.1 General . 13 5.9.3.2 High temperature . 13 5.9.3.3 Low temperature . 13 6 Transmitter . 13 SIST EN 302 617 V2.3.1:2018
ETSI ETSI EN 302 617 V2.3.1 (2018-07) 4 6.1 General . 13 6.2 Frequency error . 14 6.2.1 Definition . 14 6.2.2 Method of measurement . 14 6.2.3 Limits . 14 6.3 Carrier power . 14 6.3.1 Definitions . 14 6.3.2 Method of measurement . 14 6.3.3 Limits . 14 6.4 Amplitude modulation characteristic. 15 6.4.1 Modulation depth . 15 6.4.1.1 Definitions . 15 6.4.1.2 Method of measurement . 15 6.4.1.3 Limits . 15 6.4.2 Modulation compression . 15 6.4.2.1 Definition . 15 6.4.2.2 Method of measurement . 15 6.4.2.3 Limits . 16 6.4.3 Amplitude modulation distortion . 16 6.4.3.1 Definition . 16 6.4.3.2 Method of measurement . 16 6.4.3.3 Limits . 16 6.4.4 Audio frequency response . 16 6.4.4.1 Definition . 16 6.4.4.2 Method of measurement . 16 6.4.4.3 Limits . 16 6.5 Adjacent channel power . 17 6.5.1 Definition . 17 6.5.2 Measurement. 17 6.5.3 Limits . 17 6.6 Broadband noise . 17 6.6.1 Definition . 17 6.6.2 Method of measurement . 18 6.6.3 Limit . 18 6.7 Conducted spurious emissions (TX). 19 6.7.1 Definition . 19 6.7.2 Method of measurement . 19 6.7.3 Limits . 19 6.8 Intermodulation attenuation. 19 6.8.1 Definition . 19 6.8.2 Method of measurement . 20 6.8.3 Limits . 20 6.9 RF power attack time and release time . 21 6.9.1 Definitions . 21 6.9.2 Method of measurement . 21 6.9.2.1 Attack time . 21 6.9.2.2 Release time . 21 6.9.3 Limits . 22 6.10 Keying Transient frequency behaviour of the transmitter . 22 6.10.1 Definition . 22 6.10.2 Method of measurement . 22 6.10.3 Limits . 23 6.11 Cabinet Radiation (TX) . 23 7 Receiver . 23 7.1 Sensitivity . 23 7.1.1 Definition . 23 7.1.2 Method of measurement . 23 7.1.3 Limits . 23 7.2 Effective acceptance bandwidth . 23 7.2.1 Definition . 23 7.2.2 Method of measurement . 24 SIST EN 302 617 V2.3.1:2018
ETSI ETSI EN 302 617 V2.3.1 (2018-07) 5 7.2.3 Limits . 24 7.3 Adjacent channel rejection . 24 7.3.1 Definition . 24 7.3.2 Method of measurement . 24 7.3.3 Limits . 25 7.4 Spurious response rejection . 25 7.4.1 Definition . 25 7.4.2 Introduction to the method of measurement . 25 7.4.3 Method of search of the limited frequency range . 25 7.4.4 Method of measurement . 26 7.4.5 Limit . 26 7.5 Intermodulation response rejection . 26 7.5.1 Definition . 26 7.5.2 Method of measurement . 26 7.5.3 Limit . 27 7.6 Blocking or desensitization . 27 7.6.1 Definition . 27 7.6.2 Method of measurement . 27 7.6.3 Limit . 28 7.7 Conducted spurious emissions . 28 7.7.1 Definition . 28 7.7.2 Method of measuring the power level . 28 7.7.3 Limits . 28 7.8 Cross modulation rejection . 29 7.8.1 Definition . 29 7.8.2 Method of measurement . 29 7.8.3 Limits . 29 7.9 Receiver dynamic range . 29 7.9.1 Definition . 29 7.9.2 Method of measurement . 29 7.9.3 Limit . 30 7.10 Cabinet Radiation (RX) . 30 8 Testing for compliance with technical requirements . 30 8.1 Environmental conditions for testing . 30 8.2 Interpretation of the measurement results . 30 Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 32 Annex B (normative): Specification for adjacent channel power measurement arrangements . 34 B.1 Power measuring receiver specification . 34 B.1.1 General . 34 B.1.2 IF filter . 34 B.1.3 Attenuation indicator . 35 B.1.4 RMS value indicator . 35 B.1.5 Oscillator and amplifier . 35 Annex C (informative): Auxiliary cables . 36 Annex D (informative): Change history . 37 History . 38
SIST EN 302 617 V2.3.1:2018
ETSI ETSI EN 302 617 V2.3.1 (2018-07) 6 Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from t
...
ETSI EN 302 617 V2.3.1 (2018-07)
HARMONISED EUROPEAN STANDARD
Ground-based UHF radio transmitters,
receivers and transceivers for the UHF
aeronautical mobile service using amplitude modulation;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 ETSI EN 302 617 V2.3.1 (2018-07)
Reference
REN/ERM-TGAERO-61
Keywords
aeronautical, AM, DSB, harmonised standard,
radio, testing, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 617 V2.3.1 (2018-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions and abbreviations . 8
3.1 Definitions . 8
3.2 Abbreviations . 8
4 General requirements . 9
4.1 Frequency control . 9
4.2 Controls and indicators . 9
4.3 Class of emission and modulation characteristics . 9
4.4 Warm up . 9
4.5 Protection of the transmitter . 9
4.5.1 Definition . 9
4.5.2 Method of measurement . 9
4.5.3 Requirement . 10
5 General conditions of measurement . 10
5.1 Transmitter test signal arrangement . 10
5.1.1 Coaxial termination. 10
5.1.2 Signal sources . 10
5.1.3 Normal test signal . 10
5.2 Receiver test signal arrangement . 10
5.2.1 Test signal sources . 10
5.2.2 Nominal frequency . 10
5.2.3 Normal test signal . 10
5.2.4 Squelch . 10
5.2.5 Normal audio output power . 10
5.2.6 Audio AGC . 10
5.3 Test channels . 11
5.4 Environmental profile . 11
5.5 Test power source . 11
5.6 Normal test conditions . 11
5.6.1 Normal temperature and humidity . 11
5.6.2 Normal power sources . 11
5.6.2.1 Mains voltage and frequency . 11
5.6.2.2 Other power sources . 11
5.7 Extreme test conditions . 12
5.7.1 Extreme temperatures . 12
5.7.2 Extreme values of test power sources . 12
5.7.2.1 Mains voltage . 12
5.7.2.2 Other power sources . 12
5.8 Performance test . 12
5.9 Environmental tests . 12
5.9.1 General . 12
5.9.2 Procedure for tests at extreme temperatures . 13
5.9.3 Temperature tests . 13
5.9.3.1 General . 13
5.9.3.2 High temperature . 13
5.9.3.3 Low temperature . 13
6 Transmitter . 13
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 617 V2.3.1 (2018-07)
6.1 General . 13
6.2 Frequency error . 14
6.2.1 Definition . 14
6.2.2 Method of measurement . 14
6.2.3 Limits . 14
6.3 Carrier power . 14
6.3.1 Definitions . 14
6.3.2 Method of measurement . 14
6.3.3 Limits . 14
6.4 Amplitude modulation characteristic. 15
6.4.1 Modulation depth . 15
6.4.1.1 Definitions . 15
6.4.1.2 Method of measurement . 15
6.4.1.3 Limits . 15
6.4.2 Modulation compression . 15
6.4.2.1 Definition . 15
6.4.2.2 Method of measurement . 15
6.4.2.3 Limits . 16
6.4.3 Amplitude modulation distortion . 16
6.4.3.1 Definition . 16
6.4.3.2 Method of measurement . 16
6.4.3.3 Limits . 16
6.4.4 Audio frequency response . 16
6.4.4.1 Definition . 16
6.4.4.2 Method of measurement . 16
6.4.4.3 Limits . 16
6.5 Adjacent channel power . 17
6.5.1 Definition . 17
6.5.2 Measurement. 17
6.5.3 Limits . 17
6.6 Broadband noise . 17
6.6.1 Definition . 17
6.6.2 Method of measurement . 18
6.6.3 Limit . 18
6.7 Conducted spurious emissions (TX). 19
6.7.1 Definition . 19
6.7.2 Method of measurement . 19
6.7.3 Limits . 19
6.8 Intermodulation attenuation. 19
6.8.1 Definition . 19
6.8.2 Method of measurement . 20
6.8.3 Limits . 20
6.9 RF power attack time and release time . 21
6.9.1 Definitions . 21
6.9.2 Method of measurement . 21
6.9.2.1 Attack time . 21
6.9.2.2 Release time . 21
6.9.3 Limits . 22
6.10 Keying Transient frequency behaviour of the transmitter . 22
6.10.1 Definition . 22
6.10.2 Method of measurement . 22
6.10.3 Limits . 23
6.11 Cabinet Radiation (TX) . 23
7 Receiver . 23
7.1 Sensitivity . 23
7.1.1 Definition . 23
7.1.2 Method of measurement . 23
7.1.3 Limits . 23
7.2 Effective acceptance bandwidth . 23
7.2.1 Definition . 23
7.2.2 Method of measurement . 24
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 617 V2.3.1 (2018-07)
7.2.3 Limits . 24
7.3 Adjacent channel rejection . 24
7.3.1 Definition . 24
7.3.2 Method of measurement . 24
7.3.3 Limits . 25
7.4 Spurious response rejection . 25
7.4.1 Definition . 25
7.4.2 Introduction to the method of measurement . 25
7.4.3 Method of search of the limited frequency range . 25
7.4.4 Method of measurement . 26
7.4.5 Limit . 26
7.5 Intermodulation response rejection . 26
7.5.1 Definition . 26
7.5.2 Method of measurement . 26
7.5.3 Limit . 27
7.6 Blocking or desensitization . 27
7.6.1 Definition . 27
7.6.2 Method of measurement . 27
7.6.3 Limit . 28
7.7 Conducted spurious emissions . 28
7.7.1 Definition . 28
7.7.2 Method of measuring the power level . 28
7.7.3 Limits . 28
7.8 Cross modulation rejection . 29
7.8.1 Definition . 29
7.8.2 Method of measurement . 29
7.8.3 Limits . 29
7.9 Receiver dynamic range . 29
7.9.1 Definition . 29
7.9.2 Method of measurement . 29
7.9.3 Limit . 30
7.10 Cabinet Radiation (RX) . 30
8 Testing for compliance with technical requirements . 30
8.1 Environmental conditions for testing . 30
8.2 Interpretation of the measurement results . 30
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Specification for adjacent channel power measurement
arrangements . 34
B.1 Power measuring receiver specification . 34
B.1.1 General . 34
B.1.2 IF filter . 34
B.1.3 Attenuation indicator . 35
B.1.4 RMS value indicator . 35
B.1.5 Oscillator and amplifier . 35
Annex C (informative): Auxiliary cables . 36
Annex D (informative): Change history . 37
History . 38
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 617 V2.3.1 (2018-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the prese
...
Draft ETSI EN 302 617 V2.3.0 (2018-03)
HARMONISED EUROPEAN STANDARD
Ground-based UHF radio transmitters,
receivers and transceivers for the UHF
aeronautical mobile service using amplitude modulation;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 617 V2.3.0 (2018-03)
Reference
REN/ERM-TGAERO-61
Keywords
aeronautical, AM, DSB, harmonised standard,
radio, testing, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 617 V2.3.0 (2018-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions and abbreviations . 8
3.1 Definitions . 8
3.2 Abbreviations . 8
4 General requirements . 9
4.1 Frequency control . 9
4.2 Controls and indicators . 9
4.3 Class of emission and modulation characteristics . 9
4.4 Warm up . 9
4.5 Protection of the transmitter . 9
4.5.1 Definition . 9
4.5.2 Method of measurement . 9
4.5.3 Requirement . 10
5 General conditions of measurement . 10
5.1 Transmitter test signal arrangement . 10
5.1.1 Coaxial termination. 10
5.1.2 Signal sources . 10
5.1.3 Normal test signal . 10
5.2 Receiver test signal arrangement . 10
5.2.1 Test signal sources . 10
5.2.2 Nominal frequency . 10
5.2.3 Normal test signal . 10
5.2.4 Squelch . 10
5.2.5 Normal audio output power . 10
5.2.6 Audio AGC . 10
5.3 Test channels . 11
5.4 Environmental profile . 11
5.5 Test power source . 11
5.6 Normal test conditions . 11
5.6.1 Normal temperature and humidity . 11
5.6.2 Normal power sources . 11
5.6.2.1 Mains voltage and frequency . 11
5.6.2.2 Other power sources . 11
5.7 Extreme test conditions . 12
5.7.1 Extreme temperatures . 12
5.7.2 Extreme values of test power sources . 12
5.7.2.1 Mains voltage . 12
5.7.2.2 Other power sources . 12
5.8 Performance test . 12
5.9 Environmental tests . 12
5.9.1 General . 12
5.9.2 Procedure for tests at extreme temperatures . 13
5.9.3 Temperature tests . 13
5.9.3.1 General . 13
5.9.3.2 High temperature . 13
5.9.3.3 Low temperature . 13
6 Transmitter . 13
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 617 V2.3.0 (2018-03)
6.1 General . 13
6.2 Frequency error . 14
6.2.1 Definition . 14
6.2.2 Method of measurement . 14
6.2.3 Limits . 14
6.3 Carrier power . 14
6.3.1 Definitions . 14
6.3.2 Method of measurement . 14
6.3.3 Limits . 14
6.4 Amplitude modulation characteristic. 15
6.4.1 Modulation depth . 15
6.4.1.1 Definitions . 15
6.4.1.2 Method of measurement . 15
6.4.1.3 Limits . 15
6.4.2 Modulation compression . 15
6.4.2.1 Definition . 15
6.4.2.2 Method of measurement . 15
6.4.2.3 Limits . 16
6.4.3 Amplitude modulation distortion . 16
6.4.3.1 Definition . 16
6.4.3.2 Method of measurement . 16
6.4.3.3 Limits . 16
6.4.4 Audio frequency response . 16
6.4.4.1 Definition . 16
6.4.4.2 Method of measurement . 16
6.4.4.3 Limits . 16
6.5 Adjacent channel power . 17
6.5.1 Definition . 17
6.5.2 Measurement. 17
6.5.3 Limits . 17
6.6 Broadband noise . 17
6.6.1 Definition . 17
6.6.2 Method of measurement . 18
6.6.3 Limit . 18
6.7 Conducted spurious emissions (TX). 19
6.7.1 Definition . 19
6.7.2 Method of measurement . 19
6.7.3 Limits . 19
6.8 Intermodulation attenuation. 19
6.8.1 Definition . 19
6.8.2 Method of measurement . 20
6.8.3 Limits . 20
6.9 RF power attack time and release time . 21
6.9.1 Definitions . 21
6.9.2 Method of measurement . 21
6.9.2.1 Attack time . 21
6.9.2.2 Release time . 21
6.9.3 Limits . 22
6.10 Keying Transient frequency behaviour of the transmitter . 22
6.10.1 Definition . 22
6.10.2 Method of measurement . 22
6.10.3 Limits . 23
6.11 Cabinet Radiation (TX) . 23
7 Receiver . 23
7.1 Sensitivity . 23
7.1.1 Definition . 23
7.1.2 Method of measurement . 23
7.1.3 Limits . 23
7.2 Effective acceptance bandwidth . 23
7.2.1 Definition . 23
7.2.2 Method of measurement . 24
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 617 V2.3.0 (2018-03)
7.2.3 Limits . 24
7.3 Adjacent channel rejection . 24
7.3.1 Definition . 24
7.3.2 Method of measurement . 24
7.3.3 Limits . 25
7.4 Spurious response rejection . 25
7.4.1 Definition . 25
7.4.2 Introduction to the method of measurement . 25
7.4.3 Method of search of the limited frequency range . 25
7.4.4 Method of measurement . 26
7.4.5 Limit . 26
7.5 Intermodulation response rejection . 26
7.5.1 Definition . 26
7.5.2 Method of measurement . 26
7.5.3 Limit . 27
7.6 Blocking or desensitization . 27
7.6.1 Definition . 27
7.6.2 Method of measurement . 27
7.6.3 Limit . 28
7.7 Conducted spurious emissions . 28
7.7.1 Definition . 28
7.7.2 Method of measuring the power level . 28
7.7.3 Limits . 28
7.8 Cross modulation rejection . 29
7.8.1 Definition . 29
7.8.2 Method of measurement . 29
7.8.3 Limits . 29
7.9 Receiver dynamic range . 29
7.9.1 Definition . 29
7.9.2 Method of measurement . 29
7.9.3 Limit . 30
7.10 Cabinet Radiation (RX) . 30
8 Testing for compliance with technical requirements . 30
8.1 Environmental conditions for testing . 30
8.2 Interpretation of the measurement results . 30
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Specification for adjacent channel power measurement
arrangements . 34
B.1 Power measuring receiver specification . 34
B.1.1 General . 34
B.1.2 IF filter . 34
B.1.3 Attenuation indicator . 35
B.1.4 RMS value indicator . 35
B.1.5 Oscillator and amplifier . 35
Annex C (informative): Auxiliary cables . 36
Annex D (informative): Change history . 37
History . 38
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 617 V2.3.0 (2018-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.