SIST EN 302 502 V1.1.1:2006
(Main)Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data transmitting systems; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data transmitting systems; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
The present document is applicable to radio equipment for Fixed Broadband Data Transmitting Systems operating in the 5,8 GHz band (5 725 MHz to 5 875 MHz) as covered by ERC Decision [TBD]. The document is equally applicable to systems utilizing integral or non integral antennas.
The present document is intended to cover the provisions of Directive 1999/5/EC [1] (R&TTE Directive) Article 3.2, which states that: "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
Širokopasovna radijska dostopovna omrežja (BRAN) – Fiksni širokopasovni sistemi za prenos podatkov na frekvenci 5,8 GHz – Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 302 502 V1.1.1:2006
01-december-2006
âLURNRSDVRYQDUDGLMVNDGRVWRSRYQDRPUHåMD %5$1 ±)LNVQLãLURNRSDVRYQL
VLVWHPL]DSUHQRVSRGDWNRYQDIUHNYHQFL*+]±+DUPRQL]LUDQL(1NL]DMHPD
ELVWYHQH]DKWHYHþOHQDGLUHNWLYH5 77(
Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data transmitting
systems; Harmonized EN covering essential requirements of article 3.2 of the R&TTE
Directive
Ta slovenski standard je istoveten z: EN 302 502 Version 1.1.1
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
35.110 Omreževanje Networking
SIST EN 302 502 V1.1.1:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 302 502 V1.1.1:2006
---------------------- Page: 2 ----------------------
SIST EN 302 502 V1.1.1:2006
ETSI EN 302 502 V1.1.1 (2006-11)
Harmonized European Standard (Telecommunications series)
Broadband Radio Access Networks (BRAN);
5,8 GHz fixed broadband data transmitting systems;
Harmonized EN covering essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 3 ----------------------
SIST EN 302 502 V1.1.1:2006
2 ETSI EN 302 502 V1.1.1 (2006-11)
Reference
DEN/BRAN-0040006
Keywords
broadband, digital, HIPERMAN, multipoint
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2006.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 302 502 V1.1.1:2006
3 ETSI EN 302 502 V1.1.1 (2006-11)
Contents
Intellectual Property Rights.6
Foreword.6
Introduction .6
1 Scope.7
2 References.7
3 Definitions, symbols and abbreviations .8
3.1 Definitions.8
3.2 Symbols.9
3.3 Abbreviations.9
4 Technical requirements specification.10
4.1 Designation of centre frequencies and frequency error.10
4.1.1 Definition.10
4.1.2 Limits.10
4.1.3 Conformance.10
4.2 Transmitter RF output power, EIRP and EIRP spectral density.10
4.2.1 Definition.10
4.2.2 Limits.10
4.2.3 Conformance.11
4.3 Transmitter unwanted emissions .11
4.3.1 Transmitter unwanted emissions outside the 5 725 MHz to 5 875 MHz band .11
4.3.1.1 Definition.11
4.3.1.2 Limits.11
4.3.1.3 Conformance.11
4.3.2 Transmitter unwanted emissions within the 5 725 MHz to 5 875 MHz band.11
4.3.2.1 Definition.11
4.3.2.2 Limits.12
4.3.2.3 Conformance.12
4.4 Transmitter Power Control (TPC).12
4.4.1 Definition.12
4.4.2 Limit.12
4.4.3 Conformance.13
4.5 Receiver spurious emissions.13
4.5.1 Definition.13
4.5.2 Limit.13
4.5.3 Conformance.13
4.6 Dynamic Frequency Selection (DFS).13
4.6.1 Introduction.13
4.6.2 DFS Technical requirements specifications.14
4.6.2.1 Channel availability check and channel revalidation period .14
4.6.2.1.1 Definition.14
4.6.2.1.2 Limit.14
4.6.2.1.3 Conformance.14
4.6.2.2 In-Service Monitoring.14
4.6.2.2.1 Definition.14
4.6.2.2.2 Limit.14
4.6.2.2.3 Conformance.14
4.6.2.3 Channel Shutdown.15
4.6.2.3.1 Definition.15
4.6.2.3.2 Limit.15
4.6.2.3.3 Conformance.15
4.6.2.4 Non-Occupancy Period.15
4.6.2.4.1 Definition.15
4.6.2.4.2 Limit.15
ETSI
---------------------- Page: 5 ----------------------
SIST EN 302 502 V1.1.1:2006
4 ETSI EN 302 502 V1.1.1 (2006-11)
4.6.2.4.3 Conformance.15
5 Testing for compliance with technical requirements.15
5.1 Conditions of Testing .15
5.1.1 Environmental specifications.15
5.1.2 Test sequences and Traffic load.16
5.1.2.1 General test transmission sequences .16
5.1.2.2 Test transmission sequences for DFS tests.16
5.1.3 Test frequencies.16
5.1.4 Presentation of Equipment.16
5.1.4.1 Integrated and Dedicated antennas.16
5.1.4.2 Testing of host connected equipment and plug-in radio devices.16
5.1.4.2.1 The use of a host or test jig for testing Plug-In radio devices.17
5.1.4.2.2 Testing of combinations .17
5.2 Interpretation of the measurement results .18
5.3 Essential radio test suites.18
5.3.1 Product information.18
5.3.2 Frequency error.19
5.3.2.1 Test conditions.19
5.3.2.2 Test methods.19
5.3.2.2.1 Conducted measurement.19
5.3.2.2.2 Radiated measurement.19
5.3.3 Transmitter RF Output Power, EIRP, TPC and EIRP Spectral Density .20
5.3.3.1 Test conditions.20
5.3.3.2 Test method.20
5.3.3.2.1 Conducted measurement.20
5.3.3.2.2 Radiated measurement.22
5.3.4 Transmitter unwanted emissions.22
5.3.4.1 Transmitter unwanted emissions outside the 5 725 MHz to 5 875 MHz band.22
5.3.4.1.1 Test conditions.22
5.3.4.1.2 Test method.23
5.3.4.2 Transmitter unwanted emissions within the 5 725 MHz to 5 875 MHz band.24
5.3.4.2.1 Test conditions.24
5.3.4.2.2 Test method.24
5.3.4.2.2.1 Conducted measurement.24
5.3.5 Receiver spurious emissions.25
5.3.5.1 Test conditions.25
5.3.5.2 Test method.25
5.3.5.2.1 Conducted tests.25
5.3.5.2.2 Radiated tests.25
5.3.6 Dynamic Frequency Selection (DFS) .25
5.3.6.1 Test conditions.25
5.3.6.1.1 Selection of Radar Test Signals.26
5.3.6.1.2 Test Set-Up.26
5.3.6.2 Test Method.26
5.3.6.2.1 Conducted measurement.26
5.3.6.2.2 Radiated measurement.31
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT).32
Annex B (normative): Test sites and arrangements for radiated measurements.34
B.1 Test sites.34
B.1.1 Open air test sites .34
B.1.2 Anechoic chamber.35
B.1.2.1 General.35
B.1.2.2 Description.35
B.1.2.3 Influence of parasitic reflections.35
B.1.2.4 Calibration and mode of use .36
B.2 Test antenna.37
ETSI
---------------------- Page: 6 ----------------------
SIST EN 302 502 V1.1.1:2006
5 ETSI EN 302 502 V1.1.1 (2006-11)
B.3 Substitution antenna.38
Annex C (normative): General description of measurement .39
C.1 Conducted measurements.39
C.2 Radiated measurements.39
C.3 Substitution measurement.40
Annex D (normative): DFS parameters .41
Annex E (informative): The EN title in the official languages .44
History .45
ETSI
---------------------- Page: 7 ----------------------
SIST EN 302 502 V1.1.1:2006
6 ETSI EN 302 502 V1.1.1 (2006-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Broadband Radio Access Networks (BRAN).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [1] of the European Parliament and
of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [1] are given in annex A.
National transposition dates
Date of adoption of this EN: 27 October 2006
Date of latest announcement of this EN (doa): 31 January 2007
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 July 2007
Date of withdrawal of any conflicting National Standard (dow): 31 July 2008
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive. The modular
structure is shown in EG 201 399 [9].
ETSI
---------------------- Page: 8 ----------------------
SIST EN 302 502 V1.1.1:2006
7 ETSI EN 302 502 V1.1.1 (2006-11)
1 Scope
The present document is applicable to radio equipment for Fixed Broadband Data Transmitting Systems intended to
operate in the 5,8 GHz band (5 725 MHz to 5 875 MHz). The document is equally applicable to systems utilizing
integral or dedicated antennas.
The present document is intended to cover the provisions of Directive 1999/5/EC [1] (R&TTE Directive) Article 3.2,
which states that: "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
[1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[2] ETSI EN 300 019-1-0 (V2.1.2) (2003-09): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of
environmental conditions; Introduction".
[3] ETSI TR 100 028-1 (V1.4.1) (2001-12): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics;
Part 1".
[4] ETSI TR 100 028-2 (V1.4.1) (2001-12): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics;
Part 2".
[5] CISPR 16-1-1 Second Edition 2006-03: "Specification for radio disturbance and immunity
measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring
apparatus - Measuring apparatus".
[6] CISPR 16-2-1 Edition 1.1 2005-09: "Specification for radio disturbance and immunity measuring
apparatus and methods - Part 2-1: Methods of measurement of disturbances and immunity -
Conducted disturbance measurements".
[7] CISPR/TR 16-3 Second Edition 2003-11: "Specification for radio disturbance and immunity
measuring apparatus and methods - Part 3: CISPR technical reports".
[8] CEPT/ECC Report 68 (Riga, June 2005): "Compatibility studies in the band 5725-5875 MHz
between Fixed Wireless Access (FWA) systems and other systems".
[9] ETSI EG 201 399 (V2.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
A guide to the production of candidate Harmonized Standards for application under the R&TTE
Directive".
ETSI
---------------------- Page: 9 ----------------------
SIST EN 302 502 V1.1.1:2006
8 ETSI EN 302 502 V1.1.1 (2006-11)
[10] CEPT/ERC Recommendation 74-01: "Unwanted Emissions in the Spurious Domain" (Siófok 98,
Nice 99, Sesimbra 02, Hradec Kralove 05).
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in the R&TTE Directive [1] and the following
apply:
antenna assembly: combination of the antenna (integral or dedicated), its coaxial cable and if applicable, its antenna
connector and associated switching components
available channel: channel identified as usable as an Operating Channel
burst: period during which radio waves are intentionally transmitted, preceded and succeeded by periods during which
no intentional transmission is made
dedicated antenna: antenna external to the equipment, using an antenna connector with a cable or a wave-guide
NOTE: The antenna has been designed or developed for one or more specific types of equipment. It is the
combination of dedicated antenna and radio equipment that is expected to be compliant with the
regulations.
environmental profile: declared range of environmental conditions under which equipment within the scope of
EN 302 502 is required to be compliant
in-service monitoring: mechanism to check a channel in use by the device for the presence of a radar signal with a
level above the Interference Detection Threshold
integral antenna: antenna designed as a fixed part of the equipment, without the use of an external connector and as
such which can not be disconnected from the equipment by a user with the intend to connect another antenna.
NOTE 1: An integral antenna may be fitted internally or externally. In the case where the antenna is external, a
non-detachable cable or wave-guide can be used.
NOTE 2: Even when equipment with an integral antenna is concerned, it might still be possible to separate the
antenna from the equipment using a special tool. In such cases the assessment of the radio equipment and
of the antenna against requirements of the present document may be done separately.
manufacturer: manufacturer or his authorized representative established in the Community
NOTE 1: See R&TTE Directive [1], annex II.
NOTE 2: Or the person responsible for placing the apparatus on the market (R&TTE Directive [1], article 6.3).
operating channel: Available Channel on which the FWA device has start
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.