iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1555-3:2003/A1:2005

(Amendment)

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings

This Part of prEN 1555 specifies the characteristics of fusion fittings made from polyethylene(PE) as well as of mechanical fittings made from PE and other materials for piping systems in the field of the supply of gaseous fuels. It also specifies the test parameters for the test methods referred to in the present standard. In conjunction with the other Parts of prEN 1555, it is applicable to PE fittings, their joints and to joints with components of PE and other materials intended to be used under the following conditions:- a maximum operating pressure, MOP, up to and including 10 bar; - an operating temperature of 20°C as ref.

Kunststoff-Rohrleitungssysteme für die Gasversorgung - Polyethylen (PE) - Teil 3: Formstücke

Systemes de canalisations en plastique pour la distribution de combustibles gazeux - Polyethylene (PE) - Partie 3: Raccords

Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Polietilen (PE) - 3. del: Fitingi

General Information

Status
Withdrawn
Publication Date
30-Jun-2005
Withdrawal Date
07-Nov-2010
ICS
83.140.30 - Plastics pipes and fittings for non fluid use
91.140.40 - Gas supply systems
Technical Committee
PCV - Plastic pipes, fittings and valves
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
20-Oct-2010
Due Date
12-Nov-2010
Completion Date
08-Nov-2010
Directive
89/106/EEC - Construction products
Ref Project
EN 1555-3:2002/A1:2005 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings

Relations

Replaced By
SIST EN 1555-3:2010 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
Effective Date
01-Dec-2010
Amends
SIST EN 1555-3:2003 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
Effective Date
22-Dec-2008
Amends
SIST EN 1555-3:2003 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
Effective Date
08-Jun-2022

Buy Standard

EN 1555-3:2003/A1:2005EN 1555-3:2003/A1:2005
PreviousNext
Amendment
EN 1555-3:2003/A1:2005
English language
3 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1555-3:2003/A1:2005
01-julij-2005
Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Polietilen
(PE) - 3. del: Fitingi
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3:
Fittings
Kunststoff-Rohrleitungssysteme für die Gasversorgung - Polyethylen (PE) - Teil 3:
Formstücke
Systemes de canalisations en plastique pour la distribution de combustibles gazeux -
Polyethylene (PE) - Partie 3: Raccords
Ta slovenski standard je istoveten z: EN 1555-3:2002/A1:2005
ICS:
83.140.30 Cevi, fitingi in ventili iz Plastics pipes, fittings and
polimernih materialov valves
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
SIST EN 1555-3:2003/A1:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1555-3:2003/A1:2005

---------------------- Page: 2 ----------------------

SIST EN 1555-3:2003/A1:2005
EUROPEAN STANDARD
EN 1555-3:2002/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2005
ICS 23.040.45; 91.140.40
English version
Plastics piping systems for the supply of gaseous fuels -
Polyethylene (PE) - Part 3: Fittings
Systèmes de canalisations en plastique pour la distribution Kunststoff-Rohrleitungssysteme für die Gasversorgung -
de combustibles gazeux - Polyethylène (PE) - Partie 3: Polyethylen (PE) - Teil 3: Formstücke
Raccords
This amendment A1 modifies the European Standard EN 1555-3:2002; it was approved by CEN on 3 April 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyp
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST-TS CEN/TS 1555-7:2022(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
CEN/TS 1555-7:2021

This Technical Specification gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of FprEN 1555 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
It is recommended that the quality management system conforms to or isF no less stringent than the relevant requirements to EN ISO 9001 [2].
NOTE 1   If certification is involved, the certification and inspection body is preferably compliant with EN 45011 [3], EN 45012 [4] or EN ISO/IEC 17020 [5], as applicable.
In conjunction with Parts 1 to 5 of EN 1555 (see Foreword), this Technical Specification is applicable to polyethylene (PE) plastics piping systems for the supply of gaseous fuels. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a)   a maximum operating pressure, MOP, up to and including 10 bar );
b)   an operating temperature of 20 °C as reference temperature.
NOTE 2   For other operating temperatures, derating coefficients can be used; see EN 1555-5.
For mechanical fittings conforming to ISO 17885, guidance for assessment of conformity is not given in this part of EN 1555. When requested, a quality plan based on the tests mentioned should be set up in agreement between user and manufacturer.
EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Technical specification
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-5:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 1555-5:2021

This part of EN 1555 specifies requirements of fitness for purpose of the polyethylene (PE) piping system in the field of the supply of gaseous fuels.
It specifies the definitions of electrofusion, butt fusion and mechanical joints.
It specifies the method of preparation of test piece joints, and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions.
It specifies the test parameters for the test methods referred to in this document.
NOTE 1   This document is intended only to be used by the product manufacturer to assess the performance of components according to EN 1555-2, EN 1555-3, and/or EN 1555-4 when joined together under normal and extreme conditions in accordance with this document. It is not intended for on-site testing of pipe systems.
In conjunction with Parts 1 to 4 of EN 1555, it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a)   a maximum operating pressure, MOP, up to and including 10 bar  ;
b)   an operating temperature of 20 °C as reference temperature.
NOTE 2   For other operating temperatures, derating coefficients can be used, see Annex A.
EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-2:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
EN 1555-2:2021

This part of EN 1555 specifies the characteristics of pipes made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with Parts 1 and 3 to 5 of EN 1555, it is applicable to PE pipes, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)    a maximum operating pressure, MOP, up to and including 10 bar 1);
b)   an operating temperature of 20 °C as reference temperature.
NOTE 1   For other operating temperatures, derating coefficients should be used, see FprEN 1555-5.
EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives.
It covers three types of pipe:
-   PE pipes (outside diameter dn) including any identification stripes;
-   PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe (total outside diameter dn) as specified in Annex A, where all layers have the same MRS rating;
-   PE pipes (outside diameter dn) with a peelable, contiguous thermoplastics additional layer on the outside of the pipe (‘coated pipe’) as specified in Annex B.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-3:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
EN 1555-3:2021

This document specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with Parts 1, 2, 4 and 5 of EN 1555, it is applicable to PE fittings, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)   a maximum operating pressure, MOP, up to and including 10 bar;
b)   an operating temperature of 20 °C as reference temperature.
NOTE 1   For other operating temperatures, derating coefficients should be used; see EN 1555-5.
EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
This document is applicable for fittings of the following types:
c)   electrofusion socket fittings;
d)   electrofusion saddle fittings;
e)   spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion);
f)   mechanical fittings.
The fittings can e.g. be in the form of couplers, equal and reduced tees, reducers, bends or caps.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-1:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
EN 1555-1:2021

This part of EN 1555 specifies the general aspects of polyethylene (PE) piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with Parts 2 to 5 of EN 1555 it is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a)   a maximum operating pressure, MOP, up to and including 10 bar  );
b)   an operating temperature of 20 °C as reference temperature.
NOTE 1   For other operating temperatures, derating coefficients should be used, see EN 1555-5 [6].
EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-4:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves
EN 1555-4:2021

This European Standard specifies the characteristics of valves made from polyethylene (PE) for piping systems in the field of the supply of gaseous fuels.
NOTE 1   Valves made from other material than polyethylene designed for the supply of gaseous fuels conforming to the relevant standards are permitted to be used in PE piping system according to EN 1555 provided they have relevant PE connection for butt fusion or electrofusion ends (see EN 1555 3).
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with Parts 1, 2, 3 and 5 of EN 1555, it is applicable to PE valves, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 10 bar  );
b) an operating temperature of 20 °C as reference temperature;
NOTE 2   For other operating temperatures, derating coefficients should be used, see EN 1555 5.
c) an operating temperature between -20 °C and +40 °C.
EN 1555 covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to bi-directional valves with spigot end or electrofusion socket intended to be fused with PE pipes conforming to EN 1555 2 without any fittings or with PE fittings conforming to EN 1555 3.
This European Standard covers valves for pipes with a nominal outside diameter dn  315 mm.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 11299-2:2019(Main)
Plastics piping systems for renovation of underground gas supply networks - Part 2: Lining with continuous pipes (ISO 11299-2:2018)
EN ISO 11299-2:2018

This document, read in conjunction with Part 1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground gas supply networks. It is applicable to polyethylene (PE) pipes of three different types: PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
PE pipes with co-­‐extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified  in Annex A, where all layers have the same MRS rating;
PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer
on the outside of the pipe (“coated pipe”), see Annex A.
In addition it covers:
jointing of pipe lengths by means of butt fusion;
fabricated and injection-­‐moulded fittings made of PE;

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 11299-1:2019(Main)
Plastics piping systems for renovation of underground gas supply networks - Part 1: General (ISO 11299-1:2018)
EN ISO 11299-1:2018

This document specifies the requirements and test methods for plastics piping systems intended to be
used for the renovation of underground gas supply networks. It is applicable to pipes and fittings, as
manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or
any sprayed coatings or annular filler.
This document gives the general requirements common to all relevant renovation techniques.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 11299-3:2019(Main)
Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes (ISO 11299-3:2018)
EN ISO 11299-3:2018

This document, in conjunction with ISO 11299-1, specifies requirements and test methods for close-fit
lining systems intended to be used for the renovation of gas supply networks.
It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable
to polyethylene (PE) pipe of either solid wall single layer or co-extruded layer construction, which is
reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe
liner, as well as associated fittings and joints for the construction of the lining system. This document is
not applicable for coated PE pipes having a peelable, contiguous, thermoplastics additional layer on the
outside of the pipes.
It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of
20 °C as the reference temperature.
NOTE For other operating temperatures, guidance is given in ISO 4437-5:2014.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1555-3:2010/kFprA1:2012(Amendment)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
EN 1555-3:2010/FprA1
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day