IMT cellular networks - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU - Part 11: CDMA Direct Spread (UTRA FDD) Repeaters

The present document applies to the following equipment types:
1)   Repeaters for IMT-2000 CDMA Direct Spread (UTRA FDD)
The present document covers requirements for UTRA FDD Repeater for Releases 4, 5, 6, 7, 8, 9, 10 and 11. This
includes the requirements for Repeater operating bands from 3GPP Release 12. In addition, the present document
covers requirements for UTRA Repeater in the operating bands specified in ETSI TS 102 735 [i.9].
The present document contains requirements to demonstrate that Radio equipment both effectively uses and supports
1)   the efficient use of radio spectrum in order to avoid harmful interference.

Celična omrežja IMT - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU - 11. del: Ponavljalniki s CDMA z neposrednim razprševanjem (“Direct Spread”) (UTRA FDD)

Ta dokument se uporablja za opremo naslednje vrste:
1)   ponavljalniki za IMT-2000 CDMA z neposrednim razprševanjem (»Direct Spread«) (UTRA FDD)
Ta dokument zajema zahteve za ponavljalnike UTRA FDD iz izdaj 4, 5, 6, 7, 8, 9, 10 in 11. To
vključuje zahteve za pasove, v katerih deluje ponavljalnik iz izdaje 12 standarda 3GPP. Poleg tega ta dokument zajema
zahteve za ponavljalnike UTRA, ki delujejo v pasovih, določenih v dokumentu ETSI TS 102 735 [i.9].
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da radijska oprema učinkovito uporablja in tudi podpira
1)   učinkovito uporabo radijskega spektra, tako da ne pride do škodljivih motenj.

General Information

Status
Withdrawn
Public Enquiry End Date
19-Apr-2016
Publication Date
18-May-2016
Withdrawal Date
06-Aug-2019
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
29-Jul-2019
Due Date
21-Aug-2019
Completion Date
07-Aug-2019
Mandate

Buy Standard

Standard
SIST EN 301 908-11 V11.1.1:2016
English language
32 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ETSI EN 301 908-11 V11.1.1 (2016-05) - IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 11: CDMA Direct Spread (UTRA FDD) Repeaters
English language
32 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.HGQLPIMT cellular networks - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU - Part 11: CDMA Direct Spread (UTRA FDD) Repeaters33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 301 908-11 V11.1.1 (2016-05)SIST EN 301 908-11 V11.1.1:2016en01-julij-2016SIST EN 301 908-11 V11.1.1:2016SLOVENSKI

STANDARD
SIST EN 301 908-11 V11.1.1:2016

ETSI EN 301 908-11 V11.1.1 (2016-05) IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 11: CDMA Direct Spread (UTRA FDD) Repeaters

HARMONISED EUROPEAN STANDARD SIST EN 301 908-11 V11.1.1:2016
ETSI ETSI EN 301 908-11 V11.1.1 (2016-05) 2

Reference REN/MSG-TFES-11-11-RED Keywords 3G, 3GPP, cellular, digital, IMT, IMT-2000, mobile, radio, regulation, repeater, testing, UMTS, UTRA, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88

Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016. All rights reserved.

DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-11 V11.1.1:2016

ETSI ETSI EN 301 908-11 V11.1.1 (2016-05) 3 Contents Intellectual Property Rights ................................................................................................................................ 5 Foreword ............................................................................................................................................................. 5 Modal verbs terminology .................................................................................................................................... 5 Introduction ........................................................................................................................................................ 5 1 Scope ........................................................................................................................................................ 6 2 References ................................................................................................................................................ 6 2.1 Normative references ......................................................................................................................................... 6 2.2 Informative references ........................................................................................................................................ 7 3 Definitions, symbols and abbreviations ................................................................................................... 7 3.1 Definitions .......................................................................................................................................................... 7 3.2 Symbols .............................................................................................................................................................. 8 3.3 Abbreviations ..................................................................................................................................................... 8 4 Technical requirements specifications ..................................................................................................... 9 4.1 Environmental profile ......................................................................................................................................... 9 4.2 Conformance requirements ................................................................................................................................ 9 4.2.1 Introduction................................................................................................................................................... 9 4.2.2 Operating band unwanted emissions .......................................................................................................... 10 4.2.2.1 Definition .............................................................................................................................................. 10 4.2.2.2 Limit ...................................................................................................................................................... 10 4.2.2.2.1 General operating band unwanted emission requirements .............................................................. 10 4.2.2.2.2 Operating band emission mask requirements .................................................................................. 11 4.2.2.2.3 Protection of the BS receiver in the operating band ........................................................................ 12 4.2.2.2.4 Co-existence with services in adjacent frequency bands ................................................................. 12 4.2.2.2.5 Protection of DTT............................................................................................................................ 13 4.2.2.2.6 Limits for operation in Band 32 ...................................................................................................... 13 4.2.2.3 Conformance ......................................................................................................................................... 14 4.2.3 Spurious emissions ..................................................................................................................................... 14 4.2.3.1 Definition .............................................................................................................................................. 14 4.2.3.2 Limit ...................................................................................................................................................... 14 4.2.3.2.0 General ............................................................................................................................................ 14 4.2.3.2.1 Spurious emissions .......................................................................................................................... 15 4.2.3.2.2 Co-existence with other systems ..................................................................................................... 15 4.2.3.3 Conformance ......................................................................................................................................... 16 4.2.4 Maximum output power .............................................................................................................................. 16 4.2.4.1 Definition .............................................................................................................................................. 16 4.2.4.2 Limit ...................................................................................................................................................... 17 4.2.4.3 Conformance ......................................................................................................................................... 17 4.2.5 Input intermodulation ................................................................................................................................. 17 4.2.5.1 Definition .............................................................................................................................................. 17 4.2.5.2 Limit ...................................................................................................................................................... 17 4.2.5.2.1 General input intermodulation requirement ..................................................................................... 17 4.2.5.2.2 Co-existence with other systems ..................................................................................................... 18 4.2.5.3 Conformance ......................................................................................................................................... 19 4.2.6 Out of band gain ......................................................................................................................................... 19 4.2.6.1 Definition .............................................................................................................................................. 19 4.2.6.2 Limits .................................................................................................................................................... 19 4.2.6.3 Conformance ......................................................................................................................................... 20 4.2.7 Adjacent Channel Rejection Ratio .............................................................................................................. 20 4.2.7.1 Definition .............................................................................................................................................. 20 4.2.7.2 Limit ...................................................................................................................................................... 20 4.2.7.3 Conformance ......................................................................................................................................... 20 4.2.8 Output intermodulation ............................................................................................................................... 20 4.2.8.1 Definition .............................................................................................................................................. 20 4.2.8.2 Limit ...................................................................................................................................................... 21 SIST EN 301 908-11 V11.1.1:2016

ETSI ETSI EN 301 908-11 V11.1.1 (2016-05) 4 4.2.8.3 Conformance ......................................................................................................................................... 21 5 Testing for compliance with technical requirements .............................................................................. 21 5.1 Environmental conditions for testing ............................................................................................................... 21 5.2 Interpretation of the measurement results ........................................................................................................ 21 5.3 Essential radio test suites .................................................................................................................................. 23 5.3.0 Introduction................................................................................................................................................. 23 5.3.1 Operating band unwanted emission ............................................................................................................ 23 5.3.1.1 Initial conditions ................................................................................................................................... 23 5.3.1.2 Procedures ............................................................................................................................................. 23 5.3.1.3 Test requirement ................................................................................................................................... 23 5.3.2 Spurious emissions ..................................................................................................................................... 24 5.3.2.1 Initial conditions ................................................................................................................................... 24 5.3.2.2 Procedure .............................................................................................................................................. 24 5.3.2.3 Test requirement ................................................................................................................................... 24 5.3.3 Maximum output power .............................................................................................................................. 24 5.3.3.1 Initial conditions ................................................................................................................................... 24 5.3.3.2 Procedure .............................................................................................................................................. 25 5.3.3.3 Test requirement ................................................................................................................................... 25 5.3.4 Input intermodulation ................................................................................................................................. 25 5.3.4.1 Initial conditions ................................................................................................................................... 25 5.3.4.2 Procedures ............................................................................................................................................. 25 5.3.4.3 Test requirement ................................................................................................................................... 25 5.3.5 Out of band gain ......................................................................................................................................... 25 5.3.5.1 Initial conditions ................................................................................................................................... 25 5.3.5.2 Procedure .............................................................................................................................................. 26 5.3.5.3 Test requirement ................................................................................................................................... 26 5.3.6 Adjacent Channel Rejection Ratio .............................................................................................................. 26 5.3.6.1 Initial conditions ................................................................................................................................... 26 5.3.6.2 Procedures ............................................................................................................................................. 26 5.3.6.3 Test requirement ................................................................................................................................... 26 5.3.7 Output intermodulation ............................................................................................................................... 27 5.3.7.1 Initial conditions ................................................................................................................................... 27 5.3.7.2 Procedures ............................................................................................................................................. 27 5.3.7.3 Test requirement ................................................................................................................................... 27 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU ......................................................... 28 Annex B (normative): Repeater configurations ................................................................................ 29 B.1 Power supply .......................................................................................................................................... 29 B.2 Power supply options ............................................................................................................................. 29 B.3 Combining of Repeaters ......................................................................................................................... 29 Annex C (informative): Environmental profile specification ............................................................. 30 Annex D (informative): Bibliography ................................................................................................... 31 History .............................................................................................................................................................. 32

SIST EN 301 908-11 V11.1.1:2016

ETSI ETSI EN 301 908-11 V11.1.1 (2016-05) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). For non EU countries the present document may be used for regulatory (Type Approval) purposes. The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.10] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.1]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. The present document is part 11 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.3].

National transposition dates Date of adoption of this EN: 20 April 2016 Date of latest announcement of this EN (doa): 31 July 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e):

31 January 2017 Date of withdrawal of any conflicting National Standard (dow): 31 January 2018

Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to cover radio equipment within the scope of the Radio Equipment Directive [i.1]. The present document is produced following the guidance in ETSI EG 203 336 [i.2] as applicable.

SIST EN 301 908-11 V11.1.1:2016

ETSI ETSI EN 301 908-11 V11.1.1 (2016-05) 6 1 Scope The present document applies to the following equipment types: 1) Repeaters for IMT-2000 CDMA Direct Spread (UTRA FDD) This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: UTRA Repeater operating bands UTRA FDD Band Direction of transmission UTRA Repeater operating bands I Downlink 2 110 MHz to 2 170 MHz Uplink 1 920 MHz to 1 980 MHz III Downlink 1 805 MHz to 1 880 MHz Uplink 1 710 MHz to 1 785 MHz VII Downlink 2 620 MHz to 2 690 MHz Uplink 2 500 MHz to 2 570 MHz VIII Downlink 925 MHz to 960 MHz Uplink 880 MHz to 915 MHz XV Downlink 2 600 MHz to 2 620 MHz Uplink 1 900 MHz to 1 920 MHz XVI Downlink 2 585 MHz to 2 600 MHz Uplink 2 010 MHz to 2 025 MHz XX Downlink 791 MHz to 821 MHz Uplink 832 MHz to 862 MHz XXII Downlink 3 510 MHz to 3 590 MHz Uplink 3 410 MHz to 3 490 MHz XXXII (note) Downlink 1 452 MHz to 1 492 MHz Uplink N/A NOTE: The down link frequency(ies) of this band are paired with the uplink frequency(ies) of the other FDD band (external) of the dual band configuration.

The present document covers requirements for UTRA FDD Repeater for Releases 4, 5, 6, 7, 8, 9, 10 and 11. This includes the requirements for Repeater operating bands from 3GPP Release 12. In addition, the present document covers requirements for UTRA Repeater in the operating bands specified in ETSI TS 102 735 [i.9]. The present document contains requirements to demonstrate that Radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] ETSI TS 125 143 (V11.1.0) (02-2013): "Universal Mobile Telecommunications System (UMTS); UTRA repeater conformance testing (3GPP TS 25.143 version 11.1.0 Release 11)". [2] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold". [3] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat". SIST EN 301 908-11 V11.1.1:2016

ETSI ETSI EN 301 908-11 V11.1.1 (2016-05) 7 [4] ETSI TS 125 141 (V11.12.0) (01-2016): "Universal Mobile Telecommunications System (UMTS); Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 11.12.0 Release 11)". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 2014/53/EU of the European parliament and of the council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. [i.2] ETSI EG 203 336 (V1.1.1) (08-2015): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU". [i.3] ETSI EN 301 908-1 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and common requirements". [i.4] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [i.5] ETSI TS 136 104 (V11.14.0) (01-2016): "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS) radio transmission and reception (3GPP TS 36.104 version 11.14.0 Release 11)". [i.6] Recommendation ITU-R SM.329-12 (09-2012): "Unwanted emissions in the spurious domain". [i.7] ETSI EN 301 908-15 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 15: Evolved Universal Terrestrial Radio Access (E-UTRA FDD) Repeaters". [i.8] ETSI TS 125 104 (V11.12.0) (01-2016): "Universal Mobile Telecommunications System (UMTS); Base Station (BS) radio transmission and reception (FDD) (3GPP TS 25.104 version 11.12.0 Release 11)". [i.9] ETSI TS 102 735 (V7.1.0) (01-2010): "Universal Mobile Telecommunications System (UMTS); Band-specific requirements for UMTS Frequency Division Duplex (FDD) operation in the bands 1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz paired with 2 585 MHz to 2 600 MHz". [i.10] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: donor coupling loss: coupling loss between the Repeater and the donor Base Station downlink: signal path where Base Station transmits and mobile receives SIST EN 301 908-11 V11.1.1:2016

ETSI ETSI EN 301 908-11 V11.1.1 (2016-05) 8 downlink operating band: part of the operating band designated for downlink (BS transmit) maximum output power (Pmax): mean power level per carrier measured at the antenna connector of the Repeater in specified reference condition maximum rated output power: maximum rated output power of the repeater is the mean power level per carrier that the manufacturer has declared to be available at the antenna connector operating band: frequency range that is defined with a specific set of technical requirements, in which UTRA FDD operates NOTE: The operating band(s) for an UTRA FDD repeater is declared by the manufacturer according to the designations in table 1-1. Operating bands for UTRA are designated with Roman numerals, while the corresponding operating bands for E-UTRA are designated with Arabic numerals. Unless specified, operating band refers to the uplink operating band and downlink operating band. pass band: frequency range that the Repeater operates in with operational configuration NOTE: This frequency range can correspond to one or several consecutive nominal 5 MHz channels. If they are not consecutive each subset of channels has to be considered as an individual pass band. The Repeater can have one or several pass bands. repeater: device that receives, amplifies and transmits the radiated or conducted RF carrier both in the downlink direction (from the Base Station to the mobile area) and in the uplink direction (from the mobile to the Base Station) uplink: signal path where mobile transmits and Base Station receives uplink operating band: part of the operating band designated for downlink (BS transmit) 3.2 Symbols For the purposes of the present document, the following symbols apply: Δf The separation between the centre frequency of first or last 5 MHz channel used in the pass band and the nominal -3 dB point of the measuring filter closest to the carrier frequency Δfmax The largest value of Δf used for defining the requirement Ffilter Filter centre frequency PEM,N Declared emission level for channel N PEM,B32,ind Declared emission level in Band 32, ind=a, b, c, d, e Pmax Maximum output power Pout Output power 3.3 Abbreviations For the purposes of the present document, the following abb

...

ETSI EN 301 908-11 V11.1.1 (2016-05)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU;
Part 11: CDMA Direct Spread (UTRA FDD) Repeaters
---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-11 V11.1.1 (2016-05)
Reference
REN/MSG-TFES-11-11-RED
Keywords
3G, 3GPP, cellular, digital, IMT, IMT-2000,
mobile, radio, regulation, repeater, testing,
UMTS, UTRA, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-11 V11.1.1 (2016-05)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

Introduction ........................................................................................................................................................ 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 7

3 Definitions, symbols and abbreviations ................................................................................................... 7

3.1 Definitions .......................................................................................................................................................... 7

3.2 Symbols .............................................................................................................................................................. 8

3.3 Abbreviations ..................................................................................................................................................... 8

4 Technical requirements specifications ..................................................................................................... 9

4.1 Environmental profile ......................................................................................................................................... 9

4.2 Conformance requirements ................................................................................................................................ 9

4.2.1 Introduction................................................................................................................................................... 9

4.2.2 Operating band unwanted emissions .......................................................................................................... 10

4.2.2.1 Definition .............................................................................................................................................. 10

4.2.2.2 Limit ...................................................................................................................................................... 10

4.2.2.2.1 General operating band unwanted emission requirements .............................................................. 10

4.2.2.2.2 Operating band emission mask requirements .................................................................................. 11

4.2.2.2.3 Protection of the BS receiver in the operating band ........................................................................ 12

4.2.2.2.4 Co-existence with services in adjacent frequency bands ................................................................. 12

4.2.2.2.5 Protection of DTT............................................................................................................................ 13

4.2.2.2.6 Limits for operation in Band 32 ...................................................................................................... 13

4.2.2.3 Conformance ......................................................................................................................................... 14

4.2.3 Spurious emissions ..................................................................................................................................... 14

4.2.3.1 Definition .............................................................................................................................................. 14

4.2.3.2 Limit ...................................................................................................................................................... 14

4.2.3.2.0 General ............................................................................................................................................ 14

4.2.3.2.1 Spurious emissions .......................................................................................................................... 15

4.2.3.2.2 Co-existence with other systems ..................................................................................................... 15

4.2.3.3 Conformance ......................................................................................................................................... 16

4.2.4 Maximum output power .............................................................................................................................. 16

4.2.4.1 Definition .............................................................................................................................................. 16

4.2.4.2 Limit ...................................................................................................................................................... 17

4.2.4.3 Conformance ......................................................................................................................................... 17

4.2.5 Input intermodulation ................................................................................................................................. 17

4.2.5.1 Definition .............................................................................................................................................. 17

4.2.5.2 Limit ...................................................................................................................................................... 17

4.2.5.2.1 General input intermodulation requirement ..................................................................................... 17

4.2.5.2.2 Co-existence with other systems ..................................................................................................... 18

4.2.5.3 Conformance ......................................................................................................................................... 19

4.2.6 Out of band gain ......................................................................................................................................... 19

4.2.6.1 Definition .............................................................................................................................................. 19

4.2.6.2 Limits .................................................................................................................................................... 19

4.2.6.3 Conformance ......................................................................................................................................... 20

4.2.7 Adjacent Channel Rejection Ratio .............................................................................................................. 20

4.2.7.1 Definition .............................................................................................................................................. 20

4.2.7.2 Limit ...................................................................................................................................................... 20

4.2.7.3 Conformance ......................................................................................................................................... 20

4.2.8 Output intermodulation ............................................................................................................................... 20

4.2.8.1 Definition .............................................................................................................................................. 20

4.2.8.2 Limit ...................................................................................................................................................... 21

ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-11 V11.1.1 (2016-05)

4.2.8.3 Conformance ......................................................................................................................................... 21

5 Testing for compliance with technical requirements .............................................................................. 21

5.1 Environmental conditions for testing ............................................................................................................... 21

5.2 Interpretation of the measurement results ........................................................................................................ 21

5.3 Essential radio test suites .................................................................................................................................. 23

5.3.0 Introduction................................................................................................................................................. 23

5.3.1 Operating band unwanted emission ............................................................................................................ 23

5.3.1.1 Initial conditions ................................................................................................................................... 23

5.3.1.2 Procedures ............................................................................................................................................. 23

5.3.1.3 Test requirement ................................................................................................................................... 23

5.3.2 Spurious emissions ..................................................................................................................................... 24

5.3.2.1 Initial conditions ................................................................................................................................... 24

5.3.2.2 Procedure .............................................................................................................................................. 24

5.3.2.3 Test requirement ................................................................................................................................... 24

5.3.3 Maximum output power .............................................................................................................................. 24

5.3.3.1 Initial conditions ................................................................................................................................... 24

5.3.3.2 Procedure .............................................................................................................................................. 25

5.3.3.3 Test requirement ................................................................................................................................... 25

5.3.4 Input intermodulation ................................................................................................................................. 25

5.3.4.1 Initial conditions ................................................................................................................................... 25

5.3.4.2 Procedures ............................................................................................................................................. 25

5.3.4.3 Test requirement ................................................................................................................................... 25

5.3.5 Out of band gain ......................................................................................................................................... 25

5.3.5.1 Initial conditions ................................................................................................................................... 25

5.3.5.2 Procedure .............................................................................................................................................. 26

5.3.5.3 Test requirement ................................................................................................................................... 26

5.3.6 Adjacent Channel Rejection Ratio .............................................................................................................. 26

5.3.6.1 Initial conditions ................................................................................................................................... 26

5.3.6.2 Procedures ............................................................................................................................................. 26

5.3.6.3 Test requirement ................................................................................................................................... 26

5.3.7 Output intermodulation ............................................................................................................................... 27

5.3.7.1 Initial conditions ................................................................................................................................... 27

5.3.7.2 Procedures ............................................................................................................................................. 27

5.3.7.3 Test requirement ................................................................................................................................... 27

Annex A (normative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 28

Annex B (normative): Repeater configurations ................................................................................ 29

B.1 Power supply .......................................................................................................................................... 29

B.2 Power supply options ............................................................................................................................. 29

B.3 Combining of Repeaters ......................................................................................................................... 29

Annex C (informative): Environmental profile specification ............................................................. 30

Annex D (informative): Bibliography ................................................................................................... 31

History .............................................................................................................................................................. 32

ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-11 V11.1.1 (2016-05)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group

(MSG).

For non EU countries the present document may be used for regulatory (Type Approval) purposes.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.10] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document is part 11 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.3].

National transposition dates
Date of adoption of this EN: 20 April 2016
Date of latest announcement of this EN (doa): 31 July 2016
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 January 2017
Date of withdrawal of any conflicting National Standard (dow): 31 January 2018
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

Introduction

The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to

cover radio equipment within the scope of the Radio Equipment Directive [i.1]. The present document is produced

following the guidance in ETSI EG 203 336 [i.2] as applicable.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-11 V11.1.1 (2016-05)
1 Scope
The present document applies to the following equipment types:
1) Repeaters for IMT-2000 CDMA Direct Spread (UTRA FDD)

This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1.

Table 1-1: UTRA Repeater operating bands
UTRA FDD Direction of transmission UTRA Repeater operating bands
Band
I Downlink 2 110 MHz to 2 170 MHz
Uplink 1 920 MHz to 1 980 MHz
III Downlink 1 805 MHz to 1 880 MHz
Uplink 1 710 MHz to 1 785 MHz
VII Downlink 2 620 MHz to 2 690 MHz
Uplink 2 500 MHz to 2 570 MHz
VIII Downlink 925 MHz to 960 MHz
Uplink 880 MHz to 915 MHz
XV Downlink 2 600 MHz to 2 620 MHz
Uplink 1 900 MHz to 1 920 MHz
XVI Downlink 2 585 MHz to 2 600 MHz
Uplink 2 010 MHz to 2 025 MHz
XX Downlink 791 MHz to 821 MHz
Uplink 832 MHz to 862 MHz
XXII Downlink 3 510 MHz to 3 590 MHz
Uplink 3 410 MHz to 3 490 MHz
XXXII Downlink 1 452 MHz to 1 492 MHz
(note)
Uplink N/A

NOTE: The down link frequency(ies) of this band are paired with the uplink frequency(ies) of the other

FDD band (external) of the dual band configuration.

The present document covers requirements for UTRA FDD Repeater for Releases 4, 5, 6, 7, 8, 9, 10 and 11. This

includes the requirements for Repeater operating bands from 3GPP Release 12. In addition, the present document

covers requirements for UTRA Repeater in the operating bands specified in ETSI TS 102 735 [i.9].

The present document contains requirements to demonstrate that Radio equipment both effectively uses and supports

the efficient use of radio spectrum in order to avoid harmful interference.
2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

http://docbox.etsi.org/Reference.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI TS 125 143 (V11.1.0) (02-2013): "Universal Mobile Telecommunications System (UMTS);

UTRA repeater conformance testing (3GPP TS 25.143 version 11.1.0 Release 11)".

[2] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".

[3] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".

ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-11 V11.1.1 (2016-05)

[4] ETSI TS 125 141 (V11.12.0) (01-2016): "Universal Mobile Telecommunications System (UMTS);

Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 11.12.0 Release 11)".

2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European parliament and of the council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.2] ETSI EG 203 336 (V1.1.1) (08-2015): "Electromagnetic compatibility and Radio spectrum

Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised

Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU".

[i.3] ETSI EN 301 908-1 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the

essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and

common requirements".

[i.4] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters

(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".

[i.5] ETSI TS 136 104 (V11.14.0) (01-2016): "LTE; Evolved Universal Terrestrial Radio Access

(E-UTRA); Base Station (BS) radio transmission and reception (3GPP TS 36.104 version 11.14.0

Release 11)".

[i.6] Recommendation ITU-R SM.329-12 (09-2012): "Unwanted emissions in the spurious domain".

[i.7] ETSI EN 301 908-15 (V11.1.1): "IMT cellular networks; Harmonised Standard covering the

essential requirements of article 3.2 of the Directive 2014/53/EU; Part 15: Evolved Universal

Terrestrial Radio Access (E-UTRA FDD) Repeaters".

[i.8] ETSI TS 125 104 (V11.12.0) (01-2016): "Universal Mobile Telecommunications System (UMTS);

Base Station (BS) radio transmission and reception (FDD) (3GPP TS 25.104 version 11.12.0

Release 11)".

[i.9] ETSI TS 102 735 (V7.1.0) (01-2010): "Universal Mobile Telecommunications System (UMTS);

Band-specific requirements for UMTS Frequency Division Duplex (FDD) operation in the bands

1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz

paired with 2 585 MHz to 2 600 MHz".

[i.10] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.
3 Definitions, symbols and abbreviations
3.1 Definitions

For the purposes of the present document, the following terms and definitions apply:

donor coupling loss: coupling loss between the Repeater and the donor Base Station

downlink: signal path where Base Station transmits and mobile receives
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 908-11 V11.1.1 (2016-05)

downlink operating band: part of the operating band designated for downlink (BS transmit)

maximum output power (P ): mean power level per carrier measured at the antenna connector of the Repeater in

max
specified reference condition

maximum rated output power: maximum rated output power of the repeater is the mean power level per carrier that

the manufacturer has declared to be available at the antenna connector

operating band: frequency range that is defined with a specific set of technical requirements, in which UTRA FDD

operates

NOTE: The operating band(s) for an UTRA FDD repeater is declared by the manufacturer according to the

designations in table 1-1. Operating bands for UTRA are designated with Roman numerals, while the

corresponding operating bands for E-UTRA are designated with Arabic numerals. Unless specified,

operating band refers to the uplink operating band and downlink operating band.

pass band: frequency range that the Repeater operates in with operational configuration

NOTE: This frequency range can correspond to one or several consecutive nominal 5 MHz channels. If they are

not consecutive each subset of channels has to be considered as an individual pass band. The Repeater

can have one or several pass bands.

repeater: device that receives, amplifies and transmits the radiated or conducted RF carrier both in the downlink

direction (from the Base Station to the mobile area) and in the uplink direction (from the mobile to the Base Station)

uplink: signal path where mobile transmits and Base Station receives

uplink operating band: part of the operating band designated for downlink (BS transmit)

3.2 Symbols
For the purposes of the present document, the following symbols apply:

Δf The separation between the centre frequency of first or last 5 MHz channel used in the pass band

and the nominal -3 dB point of the measuring filter closest to the carrier frequency

Δf The largest value of Δf used for defining the requirement
max
F Filter centre frequency
filter
P Declared emission level for channel N
EM,N
P Declared emission level in Band 32, ind=a, b, c, d, e
EM,B32,ind
P Maximum output power
max
P Output power
out
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ACLR Adjacent Channel Leakage power Ratio
ACRR Adjacent Channel Rejection Ratio
BS Base S
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.