SIST EN ISO 2580-1:2001

Plastics - Acrylonitrile/butadiene/styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2000)

Migrated from Progress Sheet (TC Comment) (2000-07-10): new Tc forecast in BP Bli 991026

Kunststoffe - Acrylnitril/Butadien/Styrol (ABS)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 2580-1:2000)

In diesem Teil von ISO 6402 wird ein Bezeichnungssystem für Acrylnitril/Ethylen-Propylen-Dien/Styrol(AEPDS) und Acrylnitril/Chloriertes Polyethylen/Styrol (ACS)-Formmassen festgelegt, das als Grundlage für Spezifikationen dienen kann. ASA, AEPDS, ACS-Formmasse-Typen werden mit Hilfe eines Einteilungssystems voneinander unterschieden, das auf geeigneten Werte- bereichen der kennzeichnenden Eigenschaften a) Vicat-Erweichungstemperatur, b) Schmelze-Volumenfließrate, c) Izod-Kerbschlagzähigkeit, d) Biege-Modul, etc. beruht.

Plastiques - Acrylonitrile/butadiene/styrene (ABS) pour moulage et extrusion - Partie 1: Systeme de désignation et base de spécifications (ISO 2580-1:2000)

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje na osnovi terpolimerov akrilonitril/butadien/stirena (ABS) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 2580-1:2000)

General Information

• Status: Withdrawn
• Publication Date: 31-May-2001
• Withdrawal Date: 30-Apr-2003
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 01-May-2003
• Due Date: 01-May-2003
• Completion Date: 01-May-2003
• Ref Project: EN ISO 2580-1:2000 - Plastics - Acrylonitrile/butadiene/styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2000)

Relations

• Replaced By: SIST EN ISO 2580-1:2003 - Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:2002)
• Effective Date: 01-May-2003
• Replaces: SIST EN ISO 2580-1:2000 - Plastics - Acrylonitrile/butadiene/styrene (ABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 2580-1:1997)
• Effective Date: 01-Jun-2001

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 2580-1:2001
01-junij-2001
1DGRPHãþD
SIST EN ISO 2580-1:2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHQDRVQRYL
WHUSROLPHURYDNULORQLWULOEXWDGLHQVWLUHQD$%6GHO6LVWHPR]QDþHYDQMDLQ
SRGODJH]DVSHFLILNDFLMH,62
Plastics - Acrylonitrile/butadiene/styrene (ABS) moulding and extrusion materials - Part
1: Designation system and basis for specifications (ISO 2580-1:2000)
Kunststoffe - Acrylnitril/Butadien/Styrol (ABS)-Formmassen - Teil 1:
Bezeichnungssystem und Basis für Spezifikationen (ISO 2580-1:2000)
Plastiques - Acrylonitrile/butadiene/styrene (ABS) pour moulage et extrusion - Partie 1:
Systeme de désignation et base de spécifications (ISO 2580-1:2000)
Ta slovenski standard je istoveten z: EN ISO 2580-1:2000
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 2580-1:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2580-1:2001

---------------------- Page: 2 ----------------------

SIST EN ISO 2580-1:2001
EUROPEAN STANDARD
EN ISO 2580-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2000
ICS 83.080.20 Supersedes EN ISO 2580-1:1999
English version
Plastics - Acrylonitrile/butadiene/styrene (ABS) moulding and
extrusion materials - Part 1: Designation system and basis for
specifications (ISO 2580-1:2000)
Plastiques - Acrylonitrile/butadiène/styrène (ABS) pour Kunststoffe - Acrylnitril/Butadien/Styrol (ABS)-Formmassen
moulage et extrusion - Partie 1: Système de désignation et - Teil 1: Bezeichnungssystem und Basis für Spezifikationen
base de spécifications (ISO 2580-1:2000) (ISO 2580-1:2000)
This European Standard was approved by CEN on 15 December 2000.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2000 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2580-1:2000 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 2580-1:2001
Page 2
EN ISO 2580-1:2000
CORRECTED  2001-05-16
Foreword
The text of the International Standard ISO 2580-1:2000 has been prepared by Technical
Committee ISO/TC 61 "Plastics" in collaboration with Technical Committee CEN/TC 249
"Plastics", the secretariat of which is held by IBN.
This European Standard supersedes EN ISO 2580-1:1999.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by June 2001, and conflicting national
standards shall be withdrawn at the latest by June 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of the International Standard ISO 2580-1:2000 was approved by CEN as a European
Standard without any modification.
NOTE: Normative references to International Standards are listed in annex ZA (normative).

---------------------- Page: 4 ----------------------

SIST EN ISO 2580-1:2001
Page 3
EN ISO 2580-1:2000
Annex ZA (normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions
of any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications,
indicated by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 1043-1 1997 Plastics - Symbols and abbreviated terms - EN ISO 1043-1 1999
Part 1: Basic polymers and their special
characteristics
ISO 2580-2 1994 Plastics - Acrylonitrile/butadiene/styrene EN ISO 2580-2 1999
(ABS) moulding and extrusion materials -
Part 2: Preparation of test specimens and
determination of properties

---------------------- Page: 5 ----------------------

SIST EN ISO 2580-1:2001

---------------------- Page: 6 ----------------------

SIST EN ISO 2580-1:2001
INTERNATIONAL ISO
STANDARD 2580-1
Fourth edition
2000-12-15
Plastics —Acrylonitrile/butadiene/styrene
(ABS) moulding and extrusion materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Acrylonitrile/butadiène/styrène (ABS) pour moulage et
extrusion —
Partie 1: Système de désignation et base de spécifications
Reference number
ISO 2580-1:2000(E)
©
ISO 2000

---------------------- Page: 7 ----------------------

SIST EN ISO 2580-1:2001
ISO 2580-1:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 2580-1:2001
ISO 2580-1:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 2580 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 2580-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 9, Thermoplastic materials.
This fourth edition cancels and replaces the third edition (ISO 2580-1:1997), which has been technically revised.
ISO 2580 consists of the following parts, under the general title Plastics — Acrylonitrile/butadiene/styrene (ABS)
moulding and extrusion materials:
— Part 1: Designation system and basis for specifications
— Part 2: Preparation of test specimens and determination of properties
© ISO 2000 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 2580-1:2001

---------------------- Page: 10 ----------------------

SIST EN ISO 2580-1:2001
INTERNATIONAL STANDARD ISO 2580-1:2000(E)
Plastics — Acrylonitrile/butadiene/styrene (ABS) moulding and
extrusion materials —
Part 1:
Designation system and basis for specifications
1 Scope
1.1 This part of ISO 2580 establishes a system of designation for acrylonitrile/butadiene/styrene (ABS) thermo-
plastic materials, which may be used as the basis for specifications.
1.2 The types of ABS plastic are differentiated from each other by a classification system based on appropriate
levels of the designatory properties
a) Vicat softening temperature
b) melt volume-flow rate
c) Izod impact strength
d) flexural modulus
and on information about composition, intended application and/or method of processing, important properties,
additives, colorants, fillers and reinforcing materials.
1.3 This part of ISO 2580 is applicable to all acrylonitrile/butadiene/styrene materials (in which the styrene
component may be styrene itself and/or an alkyl-substituted styrene), consisting of a continuous phase based
mainly on copolymers of styrene (and/or an alkyl-substituted styrene) and acrylonitrile, a dispersed elastomeric
phase based mainly on polybutadiene, and other components in such quantities as specified in data block 1.
It applies to ABS materials ready for normal use in the form of powder, granules, pellets or chips, unmodified or
modified by colorants, additives, fillers, etc.
This part of ISO 2580 does not apply to materials
2
� with an Izod impact strength of less than 3 kJ/m ;
� containing less than 40 % by mass of butadiene in the elastomer of the elastomeric phase;
� containing less than 10 %
...