SIST EN 302 510-2 V1.1.1:2007
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Radio equipment in the frequency range 30 MHz to 37,5 MHz for Ultra Low Power Active Medical Membrane Implants and Accessories - Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Radio equipment in the frequency range 30 MHz to 37,5 MHz for Ultra Low Power Active Medical Membrane Implants and Accessories - Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
The present document applies to Ultra Low Power-Active Medical Implants (ULP-AMI), Membrane Implants, and accessories as described in Directive 90/385/EEC [6], operating in a Medical Implant Communications System (MICS) in the frequency band 30 MHz to 37,5 MHz. An AIMD is regulated under the AIMD Directive 90/385/EEC [6]: radio parts contained therein (referred to herein as ULP-AMI and ULP-AMI-P for peripheral devices) are regulated under the R&TTE Directive 1999/5/EC [1].The present document is intended to cover the provisions of Directive 1999/5/EC [1] (R&TTE Directive) article 3.2, which states that "….. radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present document.
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Radijska oprema v frekvenčnem območju od 30 MHz do 37,5 MHz za aktivne membranske medicinske vsadke ultra majhnih moči in pribor - 2. del: Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 302 510-2 V1.1.1:2007
01-december-2007
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP (50
5DGLMVNDRSUHPDYIUHNYHQþQHPREPRþMXRG0+]GR0+]]DDNWLYQH
PHPEUDQVNHPHGLFLQVNHYVDGNHXOWUDPDMKQLKPRþLLQSULERUGHO
+DUPRQL]LUDQL(1NL]DMHPDELVWYHQH]DKWHYHþOHQDGLUHNWLYH5 77(
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Radio equipment in
the frequency range 30 MHz to 37,5 MHz for Ultra Low Power Active Medical Membrane
Implants and Accessories - Part 2: Harmonized EN covering essential requirements of
article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 302 510-2 Version 1.1.1
ICS:
11.040.40 Implantanti za kirurgijo, Implants for surgery,
protetiko in ortetiko prosthetics and orthotics
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 302 510-2 V1.1.1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 302 510-2 V1.1.1:2007
---------------------- Page: 2 ----------------------
SIST EN 302 510-2 V1.1.1:2007
ETSI EN 302 510-2 V1.1.1 (2007-07)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Radio equipment in the frequency range
30 MHz to 37,5 MHz for Ultra Low Power Active
Medical Membrane Implants and Accessories;
Part 2: Harmonized EN covering essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 3 ----------------------
SIST EN 302 510-2 V1.1.1:2007
2 ETSI EN 302 510-2 V1.1.1 (2007-07)
Reference
DEN/ERM-TG30-003-2
Keywords
radio, regulation, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2007.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 302 510-2 V1.1.1:2007
3 ETSI EN 302 510-2 V1.1.1 (2007-07)
Contents
Intellectual Property Rights.5
Foreword.5
1 Scope.6
2 References.6
3 Definitions, symbols and abbreviations .7
3.1 Definitions.7
3.2 Symbols.7
3.3 Abbreviations.7
4 Technical requirements specifications .7
4.1 Environmental profile.7
4.2 Conformance requirements.7
4.2.1 Mechanical and electrical design .7
4.2.1.1 General.7
4.2.1.2 Antennas.7
4.2.1.3 Controls.7
4.2.1.4 Transmitter shut-off facility.7
4.2.2 Maximum effective radiated power of the fundamental .8
4.2.2.1 Definition.8
4.2.2.2 Limits.8
4.2.2.3 Conformance.8
4.2.3 Out of band emissions.8
4.2.3.1 Definition.8
4.2.3.2 Limits.8
4.2.3.3 Conformance.8
4.2.4 Unwanted emissions in the spurious domain.8
4.2.4.1 Definition.8
4.2.4.2 Limits.8
4.2.4.3 Conformance.8
4.2.5 Duty cycle.8
4.2.5.1 Definition.8
4.2.5.2 Limit.8
4.2.6 Receiver blocking or desensitization .9
4.2.6.1 Definition.9
4.2.6.2 Limit.9
4.2.6.3 Conformance.9
4.2.7 Spurious radiation of receivers .9
4.2.7.1 Definition.9
4.2.7.2 Limits.9
4.2.7.3 Conformance.9
5 Testing for compliance with technical requirements.9
5.1 Environmental conditions for testing .9
5.2 Interpretation of the measurement results .9
5.3 Essential radio test suites.10
5.3.1 Effective radiated power of the fundamental emission.10
5.3.2 Out of band emissions.10
5.3.3 Unwanted emissions in the spurious domain.10
5.3.4 Blocking or desensitization.10
5.3.5 Spurious radiation of receivers .10
5.3.6 Normal and extreme test-conditions .10
5.3.7 Test power source .10
5.3.8 Choice of samples for test suites.11
ETSI
---------------------- Page: 5 ----------------------
SIST EN 302 510-2 V1.1.1:2007
4 ETSI EN 302 510-2 V1.1.1 (2007-07)
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT).12
Annex B (informative): The EN title in the official languages .14
Annex C (informative): Bibliography.16
History .17
ETSI
---------------------- Page: 6 ----------------------
SIST EN 302 510-2 V1.1.1:2007
5 ETSI EN 302 510-2 V1.1.1 (2007-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [4] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Council Directive on the approximation of the laws of
the Member States relating to electromagnetic compatibility ("the EMC Directive") (2004/108/EC [5] as amended) and
Directive 1999/5/EC [1] of the European Parliament and of the Council of 9 March 1999 on radio equipment and
telecommunications terminal equipment and the mutual recognition of their conformity ("the R&TTE Directive").
The present document is part 2 of a multi-part deliverable covering inductively coupled Ultra Low Power Active
Medical Implant Membrane (ULP-AMI-M) devices in the frequency range 30 MHz to 37,5 MHz, as identified below:
Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".
Technical specifications relevant to Directive 1999/5/EC [1] are given in annex A.
National transposition dates
Date of adoption of this EN: 15 June 2007
Date of latest announcement of this EN (doa): 30 September 2007
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2008
Date of withdrawal of any conflicting National Standard (dow): 31 March 2009
ETSI
---------------------- Page: 7 ----------------------
SIST EN 302 510-2 V1.1.1:2007
6 ETSI EN 302 510-2 V1.1.1 (2007-07)
1 Scope
The present document applies to Ultra Low Power-Active Medical Implants (ULP-AMI), Membrane Implants, and
accessories as described in Directive 90/385/EEC [6], operating in a Medical Implant Communications System (MICS)
in the frequency band 30 MHz to 37,5 MHz. An AIMD is regulated under the AIMD Directive 90/385/EEC [6]: radio
parts contained therein (referred to herein as ULP-AMI and ULP-AMI-P for peripheral devices) are regulated under the
R&TTE Directive 1999/5/EC [1].The present document is intended to cover the provisions of Directive 1999/5/EC [1]
(R&TTE Directive) article 3.2, which states that "…. radio equipment shall be so constructed that it effectively uses the
spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [1] will apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
[1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[2] ETSI EN 302 510-1 (V1.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Radio equipment in the frequency range 30 MHz to 37,5 MHz for Ultra Low Power Active
Medical Membrane Implants and Accessories; Part 1: Technical characteristics and test methods".
[3] ETSI TR 100 028 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics Part 1".
[4] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[5] Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on
the approximation of the laws of the Member States relating to electromagnetic compatibility and
repealing Directive 89/336/EEC (EMC Directive).
[6] Council Directive 90/385/EEC of 20 June 1990 on the approximation of the laws of the Member
States relating to active implantable medical devices (AMD Directive).
ETSI
---------------------- Page: 8 ----------------------
SIST EN 302 510-2 V1.1.1:2007
7 ETSI EN 302 510-2 V1.1.1 (2007-07)
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in the R&TTE Directive [1] and
EN 302 510-1 [2] apply.
3.2 Symbols
For the purposes of the present document, the symbols given in EN 302 510-1 [2] apply.
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in EN 302 510-1 [2] apply.
4 Technical requirements specifications
4.1 Environmental profile
The technical requirements of the present document apply under the environmental profile for operation of the
equipment, which shall be declared by the manufacturer. The equipment shall comply with all the technical
requirements of the present document at all times when operating within the boundary limits of the declared operational
environmental profile.
4.2 Conformance requirements
4.2.1 Mechanical and electrical design
4.2.1.1 General
The equipment shall be designed, constructed and manufactured in accordance with sound engineering practice and
with the aim of minimizing harmful disturbance to other equipment and services and should not be disturbed by harmful
interference from other electronic devices. Transmitters and receivers may be individual or combination units.
4.2.1.2 Antennas
Equipment operating in the ULP-AMI band shall have an integral antenna, an external dedicated antenna or both. If
prov
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.