Alpine ski-bindings - Selection of release torque values

This International Standard specifies methods for the selection of the release torques for alpine skibindings.
It gives information necessary to determine the release torques; these are to be recommended
for use by ski-binding manufacturers in their instructions for installation and use, and by ski shops for
the adjustment of already mounted ski-bindings.
It applies to alpine ski-bindings in current use.
It might be inappropriate for non-mechanical bindings or bindings used with boots which reach more
than half-way up the lower leg.
Manufacturers may use either of the two specified methods, or a combination of the two, as the basis
for their recommended release torques.
The methods apply to torque-measuring binding test machines. If force-measuring test machines are
used, it is necessary to report the release force, calculated as shown in Clause 3.
In recommending the release torques, it is necessary to take into account the abilities of the skier
concerned by applying skier-type correction factors. For this purpose, three types of skier are defined,
as described in Annex A.

Fixations de skis alpins -- Sélection des valeurs du couple de déclenchement

ISO 8061:2015 sp�cifie des m�thodes pour la s�lection des valeurs des couples de d�clenchement des fixations de skis alpins. Elle donne les informations n�cessaires pour d�terminer les couples de d�clenchement. Il est recommand� au fabricant de les mentionner dans les instructions de montage et d'utilisation, et au d�taillant d'utiliser ces couples de d�clenchement pour r�gler les fixations d�j� mont�es.
Elle est applicable aux fixations de skis alpins d'usage courant.
Elle peut �tre inappropri�e pour les fixations non m�caniques ou pour les fixations utilis�es avec des chaussures dont la tige est plus haute que le milieu du tibia.
Le fabricant a le choix entre l'une ou l'autre des m�thodes sp�cifi�es, ou une combinaison des deux, comme base de recommandations pour le couple de d�clenchement.
Les m�thodes s'appliquent aux machines de mesure du couple de d�clenchement des fixations. Si des machines de mesure de la force sont utilis�es, il est n�cessaire de rapporter la force de d�clenchement, calcul�e tel qu'indiqu� � l'Article 3.
Pour recommander les couples de d�clenchement, il est n�cessaire de tenir compte des capacit�s du skieur concern� en appliquant les facteurs de correction. � cet effet, trois types de skieurs sont d�finis, tel que d�crit � l'Annexe A.

Varnostne vezi za alpske smuči - Metode za izbor mejnih vrednosti navora odpenjanj

Ta mednarodni standard določa metode za izbor mejnih vrednosti navora odpenjanj varnostnih vezi za alpske smuči.
Podaja informacije, ki so potrebne za določanje navora odpenjanja. Navore priporočajo
proizvajalci varnostnih vezi v navodilih za namestitev in uporabo vezi ter prodajalne smučarske opreme, če so varnostne vezi že nameščene.
Uporablja se za varnostne vezi, ki so trenutno v uporabi.
Standard morda ni primeren za nemehanske vezi ali vezi, ki se uporabljajo s čevlji, ki segajo čez polovico spodnjega dela noge.
Proizvajalci lahko uporabijo katero koli od navedenih metod ali kombinacijo obeh kot osnovo za priporočene navore odpenjanj.
Metode se uporabljajo za preskusne naprave za merjenje navora. Če so uporabljene preskusne naprave za merjenje sile, je treba navesti sprostitveno silo, ki se izračuna, kot je prikazano v 3. točki.
Pri priporočanju navorov odpenjanja je treba upoštevati sposobnosti smučarja z uporabo korekcijskih faktorjev za vrsto smučarja. V ta namen so opredeljene tri vrste smučarjev, kot je opisano v dodatku A.

General Information

Status
Published
Public Enquiry End Date
14-Sep-2017
Publication Date
14-Sep-2017
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-Sep-2017
Due Date
20-Nov-2017
Completion Date
15-Sep-2017

RELATIONS

Buy Standard

Standard
ISO 8061:2015 - Alpine ski-bindings -- Selection of release torque values
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
oSIST ISO 8061:2017
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
SIST ISO 8061:2017
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ISO 8061:2015 - Fixations de skis alpins -- Sélection des valeurs du couple de déclenchement
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 8061
Fourth edition
2015-12-15
Alpine ski-bindings — Selection of
release torque values
Fixations de skis alpins — Sélection des valeurs du couple de
déclenchement
Reference number
ISO 8061:2015(E)
ISO 2015
---------------------- Page: 1 ----------------------
ISO 8061:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 8061:2015(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Symbols .......................................................................................................................................................................................................................... 1

3 Release force ............................................................................................................................................................................................................. 2

4 Weight method ....................................................................................................................................................................................................... 2

4.1 Calculation of release torques .................................................................................................................................................... 2

4.2 Release torques corresponding to user’s maximum recommended mass .......................................... 3

4.3 Correction of the release torque .............................................................................................................................................. 3

Annex A (normative) Definition of skier type ............................................................................................................................................. 5

© ISO 2015 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 8061:2015(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity

assessment, as well as information about ISO’s adherence to the WTO principles in the Technical

Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.

The committee responsible for this document is ISO/TC 83, Sports and other recreational facilities and

equipment, Subcommittee SC 4, Snowsports equipment.

This fourth edition cancels and replaces the third edition (ISO 8061:2004), which has been technically

revised to remove Annex B. It also incorporates the Amendment ISO 8061:2004/Amd 1:2006.

iv © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 8061:2015(E)
Introduction

This International Standard is one of a series of International Standards dealing with the safety of ski

bindings; the other International Standards of this series are ISO 9462 and ISO 9465.

National standards, complying with legal regulations, may be more extensive regarding, for example,

the following:
— combined loading;
— deflexion of the ski.
International Standards covering these aspects are being prepared.

To verify the safety of ski-bindings, it is necessary to use all three International Standards of the series

and also national standards covering aspects which are not yet standardized internationally.

© ISO 2015 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 8061:2015(E)
Alpine ski-bindings — Selection of release torque values
1 Scope

This International Standard specifies methods for the selection of the release torques for alpine ski-

bindings. It gives information necessary to determine the release torques; these are to be recommended

for use by ski-binding manufacturers in their instructions for installation and use, and by ski shops for

the adjustment of already mounted ski-bindings.
It applies to alpine ski-bindings in current use.

It might be inappropriate for non-mechanical bindings or bindings used with boots which reach more

than half-way up the lower leg.

Manufacturers may use either of the two specified methods, or a combination of the two, as the basis

for their recommended release torques.
The methods apply to torque-measuring binding test machines. If force-measurin
...

SLOVENSKI STANDARD
oSIST ISO 8061:2017
01-september-2017
9DUQRVWQHYH]L]DDOSVNHVPXþL0HWRGH]DL]ERUPHMQLKYUHGQRVWLQDYRUD
RGSHQMDQM
Alpine ski-bindings - Selection of release torque values
Fixations de skis alpins -- Sélection des valeurs du couple de déclenchement
Ta slovenski standard je istoveten z: ISO 8061:2015
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
oSIST ISO 8061:2017 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST ISO 8061:2017
---------------------- Page: 2 ----------------------
oSIST ISO 8061:2017
INTERNATIONAL ISO
STANDARD 8061
Fourth edition
2015-12-15
Alpine ski-bindings — Selection of
release torque values
Fixations de skis alpins — Sélection des valeurs du couple de
déclenchement
Reference number
ISO 8061:2015(E)
ISO 2015
---------------------- Page: 3 ----------------------
oSIST ISO 8061:2017
ISO 8061:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST ISO 8061:2017
ISO 8061:2015(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Symbols .......................................................................................................................................................................................................................... 1

3 Release force ............................................................................................................................................................................................................. 2

4 Weight method ....................................................................................................................................................................................................... 2

4.1 Calculation of release torques .................................................................................................................................................... 2

4.2 Release torques corresponding to user’s maximum recommended mass .......................................... 3

4.3 Correction of the release torque .............................................................................................................................................. 3

Annex A (normative) Definition of skier type ............................................................................................................................................. 5

© ISO 2015 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST ISO 8061:2017
ISO 8061:2015(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity

assessment, as well as information about ISO’s adherence to the WTO principles in the Technical

Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.

The committee responsible for this document is ISO/TC 83, Sports and other recreational facilities and

equipment, Subcommittee SC 4, Snowsports equipment.

This fourth edition cancels and replaces the third edition (ISO 8061:2004), which has been technically

revised to remove Annex B. It also incorporates the Amendment ISO 8061:2004/Amd 1:2006.

iv © ISO 2015 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST ISO 8061:2017
ISO 8061:2015(E)
Introduction

This International Standard is one of a series of International Standards dealing with the safety of ski

bindings; the other International Standards of this series are ISO 9462 and ISO 9465.

National standards, complying with legal regulations, may be more extensive regarding, for example,

the following:
— combined loading;
— deflexion of the ski.
International Standards covering these aspects are being prepared.

To verify the safety of ski-bindings, it is necessary to use all three International Standards of the series

and also national standards covering aspects which are not yet standardized internationally.

© ISO 2015 – All rights reserved v
---------------------- Page: 7 ----------------------
oSIST ISO 8061:2017
---------------------- Page: 8 ----------------------
oSIST ISO 8061:2017
INTERNATIONAL STANDARD ISO 8061:2015(E)
Alpine ski-bindings — Selection of release torque values
1 Scope

This International Standard specifies methods for the selection of the release torques for alpine ski-

bindings. It gives information necessary to determine the release torques; these are to be recommended

for use by ski-binding manufacturers in their instructions for installation and use, and by s

...

SLOVENSKI STANDARD
SIST ISO 8061:2017
01-oktober-2017
1DGRPHãþD
SIST ISO 8061:2005
SIST ISO 8061:2005/A1:2011
9DUQRVWQHYH]L]DDOSVNHVPXþL0HWRGH]DL]ERUPHMQLKYUHGQRVWLQDYRUD
RGSHQMDQM
Alpine ski-bindings - Selection of release torque values
Fixations de skis alpins -- Sélection des valeurs du couple de déclenchement
Ta slovenski standard je istoveten z: ISO 8061:2015
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
SIST ISO 8061:2017 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 8061:2017
---------------------- Page: 2 ----------------------
SIST ISO 8061:2017
INTERNATIONAL ISO
STANDARD 8061
Fourth edition
2015-12-15
Alpine ski-bindings — Selection of
release torque values
Fixations de skis alpins — Sélection des valeurs du couple de
déclenchement
Reference number
ISO 8061:2015(E)
ISO 2015
---------------------- Page: 3 ----------------------
SIST ISO 8061:2017
ISO 8061:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 8061:2017
ISO 8061:2015(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Symbols .......................................................................................................................................................................................................................... 1

3 Release force ............................................................................................................................................................................................................. 2

4 Weight method ....................................................................................................................................................................................................... 2

4.1 Calculation of release torques .................................................................................................................................................... 2

4.2 Release torques corresponding to user’s maximum recommended mass .......................................... 3

4.3 Correction of the release torque .............................................................................................................................................. 3

Annex A (normative) Definition of skier type ............................................................................................................................................. 5

© ISO 2015 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 8061:2017
ISO 8061:2015(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity

assessment, as well as information about ISO’s adherence to the WTO principles in the Technical

Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.

The committee responsible for this document is ISO/TC 83, Sports and other recreational facilities and

equipment, Subcommittee SC 4, Snowsports equipment.

This fourth edition cancels and replaces the third edition (ISO 8061:2004), which has been technically

revised to remove Annex B. It also incorporates the Amendment ISO 8061:2004/Amd 1:2006.

iv © ISO 2015 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 8061:2017
ISO 8061:2015(E)
Introduction

This International Standard is one of a series of International Standards dealing with the safety of ski

bindings; the other International Standards of this series are ISO 9462 and ISO 9465.

National standards, complying with legal regulations, may be more extensive regarding, for example,

the following:
— combined loading;
— deflexion of the ski.
International Standards covering these aspects are being prepared.

To verify the safety of ski-bindings, it is necessary to use all three International Standards of the series

and also national standards covering aspects which are not yet standardized internationally.

© ISO 2015 – All rights reserved v
---------------------- Page: 7 ----------------------
SIST ISO 8061:2017
---------------------- Page: 8 ----------------------
SIST ISO 8061:2017
INTERNATIONAL STANDARD ISO 8061:2015(E)
Alpine ski-bindings — Selection of release torque values
1 Scope

This International Standard specifies methods for the selection of the release torques for alpine ski-

bindings. It gives information necessary to determine the release torques; these are to be recommended

for use by ski-binding manufacturers in their instructions for instal
...

NORME ISO
INTERNATIONALE 8061
Quatrième édition
2015-12-15
Fixations de skis alpins —
Sélection des valeurs du couple de
déclenchement
Alpine ski-bindings — Selection of release torque values
Numéro de référence
ISO 8061:2015(F)
ISO 2015
---------------------- Page: 1 ----------------------
ISO 8061:2015(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2015, Publié en Suisse

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni utilisée

sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie, l’affichage sur

l’internet ou sur un Intranet, sans autorisation écrite préalable. Les demandes d’autorisation peuvent être adressées à l’ISO à

l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 8061:2015(F)
Sommaire Page

Avant-propos ..............................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Domaine d’application ................................................................................................................................................................................... 1

2 Symboles ....................................................................................................................................................................................................................... 1

3 Force de déclenchement ............................................................................................................................................................................... 2

4 Méthode du poids ................................................................................................................................................................................................ 2

4.1 Calcul des couples de déclenchement ................................................................................................................................. 2

4.2 Couples de déclenchement correspondants à la masse maximale recommandée

de l’utilisateur .......................................................................................................................................................................................... 3

4.3 Correction du couple de déclenchement .......................................................................................................................... 3

Annexe A (normative) Définition du type de skieur ............................................................................................................................ 5

© ISO 2015 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 8061:2015(F)
Avant-propos

L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes

nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est

en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.

L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui

concerne la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents

critères d’approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www.

iso.org/directives).

L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de

droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant

les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de

l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de

brevets reçues par l’ISO (voir www.iso.org/brevets).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer

un engagement.

Pour une explication de la signification des termes et expressions spécifiques de l’ISO liés à

l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de l’ISO aux principes

de l’OMC concernant les obstacles techniques au commerce (OTC), voir le lien suivant: Avant-propos —

Informations supplémentaires.

Le comité chargé de l’élaboration du présent document est l’ISO/TC 83, Matériel et équipement de sports

et autres activités de loisirs, sous-comité SC 4, Équipements de sport de neige.

Cette quatrième édition annule et remplace la troisième édition (ISO 8061:2004), qui a fait

l’objet d’une révision technique en vue de supprimer l’Annexe B. Elle intègre également

l’Amendement ISO 8061:2004/Amd 1:2006.
iv © ISO 2015 – Tous droits réservés
---------------------- Page: 4 ----------------------
ISO 8061:2015(F)
Introduction

La présente Norme internationale fait partie d’une série de Normes internationales traitant de la sécurité

des fixations de ski, les autres Normes internationales de cette série étant l’ISO 9462 et l’ISO 9465.

Les normes nationales, conformes à des réglementations légales, peuvent être plus complètes, par

exemple concernant:
— la charge combinée;
— la flexion du ski.

Des Normes internationales traitant de ces aspects sont actuellement en préparation.

Pour vérifier la sécurité d’une fixation de ski, il est nécessaire d’utiliser les trois Normes internationales

de la série, et en outre les normes nationales couvrant les aspects non encore pris en compte au point de

vue international.
© ISO 2015 – Tous droits réservés v
---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 8061:2015(F)
Fixations de skis alpins — Sélection des valeurs du couple
de déclenchement
1 Domaine d’application

La présente Norme internationale spécifie des méthodes pour la sélection des valeurs des couples de

déclenchement des fixations de skis alpins. Elle donne les informations nécessaires pour déterminer les

couples de déclenchement. Il est recommandé au fabricant de les mentionner dans les instructions de

montage et d’utilisation, et au détaillant d’utiliser ces couples de déclenchement pour régler les fixations

déjà montées.
Elle est applicable aux fixations de skis alpins d’usage courant.

Elle peut être inappropriée pour les fixations non mécaniques ou pour les fixations utilisées avec des

chaussures dont la tige est plus haute que le milieu du tibia.

Le fabricant a le choix entre l’une ou l’autre des méthodes spécifiées, ou une combinaison des deux,

comme base de recommandations pour le couple de déclenchement.

Les méthodes s’appliquent aux machines de mesure du couple de déclenchement des fixations. Si des

machines de mesure de la force sont utilisées, il est nécessaire de rapporter la force de déclenchement,

calculée tel qu’indiqué à l’Article 3.
Pour recommander les couples de
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.