SIST EN 60444-8:2004
(Main)Measurement of quartz crystal unit parameters -- Part 8: Test fixture for surface mounted quartz crystal units
Measurement of quartz crystal unit parameters -- Part 8: Test fixture for surface mounted quartz crystal units
Explains the test fixture that allows the accurate measurement of resonance frequency, resonance resistance, and equivalent electrical circuit parameters of a leadless surface mounted quartz crystal units over the frequency range from 1 MHz to 150 MHz using zero phase technique as specified in EN 60444-4 and EN 60444-5.
Messung von Schwingquarz-Parametern -- Teil 8: Prüfaufbau für oberflächenmontierbare Schwingquarze
Mesure des paramètres des résonateurs à quartz -- Partie 8: Dispositif d'essai pour les résonateurs à quartz montés en surface
Présente le dispositif d'essai qui permet une mesure précise de la fréquence de résonance, de la résistance de résonance et des paramètres de circuit électrique équivalent des résonateurs à quartz sans sorties montés en surface en utilisant la technique de la phase nulle telle qu'elle est spécifiée dans la CEI 60444-4 et dans la CEI 60444-5.
Measurement of quartz crystal unit parameters - Part 8: Test fixture for surface mounted quartz crystal units (IEC 60444-8:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 60444-8:2004
STANDARD
julij 2004
Measurement of quartz crystal unit parameters - Part 8: Test fixture for surface
mounted quartz crystal units (IEC 60444-8:2003)
ICS 31.140 Referenčna številka
SIST EN 60444-8:2004(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 60444-8
NORME EUROPÉENNE
EUROPÄISCHE NORM October 2003
ICS 31.140
English version
Measurement of quartz crystal unit parameters
Part 8: Test fixture for surface mounted quartz crystal units
(IEC 60444-8:2003)
Mesure des paramètres Messung von Schwingquarz-Parametern
des résonateurs à quartz Teil 8: Prüfaufbau für oberflächen-
Partie 8: Dispositif d'essai montierbare Schwingquarze
pour les résonateurs à quartz (IEC 60444-8:2003)
montés en surface
(CEI 60444-8:2003)
This European Standard was approved by CENELEC on 2003-10-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60444-8:2003 E
---------------------- Page: 2 ----------------------
EN 60444-8:2003 - 2 -
Foreword
The text of document 49/599/FDIS, future edition 1 of IEC 60444-8, prepared by IEC TC 49,
Piezoelectric and dielectric devices for frequency control and selection, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 60444-8 on 2003-10-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-07-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2006-10-01
Annexes designated "normative" are part of the body of the standard.
In this standard, annex ZA is normative.
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60444-8:2003 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60444-4 NOTE Harmonized as EN 60444-4:1997 (not modified).
__________
---------------------- Page: 3 ----------------------
- 3 - EN 60444-8:2003
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60444-1 1986 Measurement of quartz crystal unit EN 60444-1 1997
parameters by zero phase technique in
a pi-network
Part 1: Basic method for the
measurement of resonance frequency
and resonance resistance of quartz
crystal units by zero phase technique in
a pi-network
IEC 60444-2 1980 Part 2: Phase offset method for EN 60444-2 1997
measurement of motional capacitance
of quartz crystal units
IEC 60444-5 1995 Part 5: Methods for the determination of EN 60444-5 1997
equivalent electrical parameters using
automatic network analyzer techniques
and error correction
IEC 61240 1994 Piezoelectric devices - Preparation of EN 61240 1997
outline drawings of surface-mounted
devices (SMD) for frequency control and
selection - General rules
---------------------- Page: 4 ----------------------
NORME CEI
INTERNATIONALE IEC
60444-8
INTERNATIONAL
Première édition
STANDARD
First edition
2003-07
Mesure des paramètres des résonateurs
à quartz –
Partie 8:
Dispositif d'essai pour les résonateurs
à quartz montés en surface
Measurement of quartz crystal unit
parameters –
Part 8:
Test fixture for surface mounted
quartz crystal units
© IEC 2003 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
L
Commission Electrotechnique Internationale PRICE CODE
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
Pour prix, voir catalogue en vigueur
For price, see current catalogue
---------------------- Page: 5 ----------------------
60444-8 © IEC:2003 – 3 –
CONTENTS
FOREWORD . 5
INTRODUCTION .9
1 Scope .11
2 Normative references.11
3 General issue.13
4 Leadless surface mounted quartz crystal units.13
4.1 Enclosure .13
4.2 Overtone and frequency range .13
5 Specifications of measurement method, test fixture .13
5.1 Specifications of measurement method .13
5.2 Specifications of test fixture .13
6 Calibration of measurement system and C adapter board.19
L
6.1 Calibration of measurement system.19
6.2 Calibration of C adapter board .19
L
Bibliography .21
Figure 1 – Equivalent circuit of the test fixture.15
Figure 2 – Equivalent circuit of the test fixture with load capacitance.15
Figure 3 – Three-dimensional projection for the test fixture .15
Figure 4 – Design of the test fixture .17
Figure 5 – Structure of the test fixture.19
---------------------- Page: 6 ----------------------
60444-8 © IEC:2003 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
MEASUREMENT OF QUARTZ CRYSTAL UNIT PARAMETERS –
Part 8: Test fixture for surface mounted quartz crystal units
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All us
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.