European digital cellular telecommunications system; Attachment requirements for Global System for Mobile communications (GSM) mobile stations; Access

This Technical Basis for Regulation (TBR) specifies the technical requirements to be met by terminal equipment capable of connection to a public telecommunications network. These requirements apply to terminals for phase 1 of the public land mobile radio service utilising constant envelope modulation, operating in the 900 MHz band with a channel separation of 200 kHz, and carrying 8 full rate traffic channels per carrier according to the Time Division Multiple Access (TDMA) principle. This TBR covers the requirements for Global System for Mobile communications (GSM) access to the network. For each conformance requirement, one or more test purposes are given. For each test purpose, a single reference is given to the test method in GSM 11.10 (I-ETS 300 020-1) [2]. The requirements apply at the air interface and the SIM-ME interface for the access requirements, which may be stimulated to perform the tests by additional equipment if necessary. The measurement uncertainty is handled, as described in GSM 11.10 (I-ETS 300 020-1) [2]. This TBR covers the essential requirements of the Terminal Directive 91/263/EEC [1] Articles 4d, 4e, 4f. Non access related aspects of speech telephony, where Article 4g has been applied, are covered by TBR 9 [7]. The Terminal Directive 91/263/EEC [1] Articles 4a and 4b are covered by other directives, and, therefore, not by this TBR. In this TBR, there are no EMC technical requirements in terms of the Terminal Directive 91/263/EEC [1], Article 4c. NOTE: Technical Requirements for EMC performance and testing of the equipment are covered by the relevant standards applicable to the EMC Directive 89/336/EEC, Annex A. Terminal equipment may be subject to additional requirements in other Common Technical Regulations (CTR)ydepending on the equipments functionality. GSM 11.10 (I-ETS 300 020-1) [2] constitutes the full conformance test suite for GSM. The verification of the conformance requirements in this TBR are based on the tests described in this

Evropski digitalni celieni telekomunikacijski sistem - Priključitvene zahteve mobilnih postaj sistema GSM (globalni sistem mobilnih komunikacij) - Dostop

General Information

Status
Published
Publication Date
30-Jun-2000
Withdrawal Date
30-Sep-2003
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jul-2000
Due Date
01-Jul-2000
Completion Date
01-Jul-2000
Mandate

Buy Standard

Standardization document
SIST TBR 005:2000
English language
265 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST TBR 005:2000
01-julij-2000
(YURSVNLGLJLWDOQLFHOLHQLWHOHNRPXQLNDFLMVNLVLVWHP3ULNOMXþLWYHQH]DKWHYH
PRELOQLKSRVWDMVLVWHPD*60 JOREDOQLVLVWHPPRELOQLKNRPXQLNDFLM 'RVWRS
European digital cellular telecommunications system; Attachment requirements for
Global System for Mobile communications (GSM) mobile stations; Access
Ta slovenski standard je istoveten z: TBR 005 Edition 2
ICS:
33.070.50 Globalni sistem za mobilno Global System for Mobile
telekomunikacijo (GSM) Communication (GSM)
SIST TBR 005:2000 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST TBR 005:2000
---------------------- Page: 2 ----------------------
SIST TBR 005:2000
TECHNICAL TBR 5
BASIS for October 1995
REGULATION Second Edition
Source: ETSI TC-SMG Reference: RTBR/SMG-0005
ICS: 33.060.50

European digital cellular telecommunications sytem, Global System for Mobile communications

Key words:
(GSM)
European digital cellular telecommunications sytem;
Attachment requirements for Global System for Mobile
communications (GSM) mobile stations
Access
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
F-06921 Sophia Antipolis CEDEX - FRANCE
Postal address:
650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Office address:
c=fr, a=atlas, p=etsi, s=secretariat - secretariat@etsi.fr
X.400: Internet:
Tel.: +33 92 94 42 00 - Fax: +33 93 65 47 16

Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the

foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1995. All rights reserved.
New presentation - see History box
---------------------- Page: 3 ----------------------
SIST TBR 005:2000
Page 2
TBR 5: October 1995

Whilst every care has been taken in the preparation and publication of this document, errors in content,

typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to

"ETSI Editing and Committee Support Dept." at the address shown on the title page.

---------------------- Page: 4 ----------------------
SIST TBR 005:2000
Page 3
TBR 5: October 1995
Contents

Foreword .....................................................................................................................................................11

1 Scope ................................................................................................................................................13

2 Normative references........................................................................................................................13

3 Information from the client to the test laboratory...............................................................................14

4 Other requirements for GSM mobile stations....................................................................................14

5 Structure of the TBR .........................................................................................................................14

6 References to GSM core specifications............................................................................................15

7 Abbreviations.....................................................................................................................................16

8 General tests and procedures...........................................................................................................18

8.1 Support and non-support of services.................................................................................18

8.2 Support of single numbering scheme ................................................................................19

8.3 IMEI Security......................................................................................................................20

9 Spurious emissions ...........................................................................................................................20

9.1 MS allocated a channel (conducted spurious emissions)..................................................20

9.2 MS in idle mode (conducted spurious emissions) .............................................................21

9.3 MS allocated a channel (radiated spurious emissions) .....................................................22

9.4 MS in idle mode (radiated spurious emissions).................................................................23

10 Transmitter ........................................................................................................................................23

10.1 Phase error and frequency error........................................................................................23

10.2 Frequency error under multipath and interference conditions ...........................................24

10.3 Peak transmitter carrier power and burst timing................................................................25

10.4 Output RF spectrum, modulation and switching transients ...............................................28

11 Receiver ............................................................................................................................................29

11.1 Sensitivity...........................................................................................................................29

11.1.1 Reference Sensitivity for TCH/FS .................................................................29

11.1.2 Reference sensitivity for Control Channel (CCH)..........................................30

11.2 Usable Receiver Input Level Range ..................................................................................31

11.3 Co-channel rejection..........................................................................................................32

11.3.1 TCH-Full Rate Speech ..................................................................................32

11.3.2 Control Channel ............................................................................................33

11.4 Adjacent channel rejection.................................................................................................34

11.4.1 Adjacent interferer 200 kHz (I2W).................................................................34

11.4.2 Adjacent interferer 400 kHz (I4W).................................................................35

11.5 Intermodulation rejection ...................................................................................................38

11.6 Blocking and spurious response........................................................................................39

11.6.1 TCH-Full Rate Speech ..................................................................................39

11.6.2 TCH Control Channel....................................................................................39

12 Tests of Layer 2 signalling functions .................................................................................................40

12.1 Timing requirements and frame format .............................................................................40

12.1.1 Timing requirements .....................................................................................40

12.1.2 Frame format.................................................................................................41

12.2 Initialisation when contention resolution required ..............................................................41

12.2.1 Normal initialisation .......................................................................................42

12.2.2 Initialisation failure.........................................................................................42

---------------------- Page: 5 ----------------------
SIST TBR 005:2000
Page 4
TBR 5: October 1995

12.2.2.1 Loss of UA frame.......................................................................................... 42

12.2.2.2 UA frame with different information field....................................................... 43

12.2.2.3 Information frame or supervisory frames in response to an SABM frame ... 44

12.2.3 Initialisation denial......................................................................................... 44

12.2.4 Total initialisation failure ............................................................................... 45

12.3 Initialisation, contention resolution not required ................................................................ 46

12.3.1 Normal initialisation....................................................................................... 46

12.3.2 Initialisation failure ........................................................................................ 47

12.3.3 Initialisation denial......................................................................................... 47

12.3.4 Total initialisation failure ............................................................................... 48

12.4 Normal information transfer .............................................................................................. 49

12.4.1 Sequence counting and I frame acknowledgements.................................... 49

12.4.2 Receipt of an I frame in the timer recovery state.......................................... 50

12.4.3 Segmentation and concatenation ................................................................. 51

12.5 Normal Layer 2 disconnection........................................................................................... 52

12.6 RR response frame loss (MS to SS)................................................................................. 52

12.7 Test of frame transmission with incorrect C/R value......................................................... 53

12.8 Test of errors in the control field........................................................................................ 54

12.9 Test on receipt of invalid frame......................................................................................... 54

13 Initial Tests........................................................................................................................................ 56

13.1 Scheduling of the channel request transmission............................................................... 56

13.1.1 Txinteger is low, non-combined case ........................................................... 56

13.1.2 Txinteger is low, combined case .................................................................. 57

13.1.3 Txinteger and Maxretrans are put to random values, non combined case .. 59

13.1.4 Txinteger and Maxretrans are put to random values, combined case ......... 60

13.1.5 Test of random generator............................................................................. 61

13.2 IMSI detach/attach ............................................................................................................ 62

13.2.1 IMSI attach and detach are not allowed, SIM remains continuously in the

ME ................................................................................................................ 62

13.2.2 IMSI attach and detach are not allowed, SIM is removed and put again...... 63

13.2.3 IMSI attach and detach are required, the MS is powered off........................ 64

13.2.4 IMSI attach and detach are required, the MS is powered on........................ 64

13.2.5 IMSI attach and detach are required, SIM is removed ................................. 65

13.2.6 IMSI attach and detach are required, SIM is inserted................................... 66

13.3 Test of sequenced MM/CC message transfer .................................................................. 67

14 Test of MS functions in idle mode .................................................................................................... 67

14.1 MS indication of available PLMNs..................................................................................... 67

14.2 MS will send only if BSS is "On air"................................................................................... 68

15 Test of L3 error handling .................................................................................................................. 69

15.1 Errors in L3 messages ...................................................................................................... 69

15.1.1 Wrong protocol discriminator........................................................................ 69

15.2 Test of MS reaction to errors in Transaction Identifier ...................................................... 69

15.2.1 Test of TI error in RR management message.............................................. 69

15.2.2 Test of TI error in MM message ................................................................... 70

15.2.3 Test of TI error in CC message .................................................................... 71

15.2.3.1 Test of TI error in CC message - 1st case ................................................... 71

15.2.3.2 Test of TI error in CC message - 2nd case .................................................. 71

15.2.3.3 Test of TI error in CC message - 3rd case................................................... 72

15.2.3.4 Test of TI error in CC message - 4th case ................................................... 72

15.3 Test of message type errors ............................................................................................. 73

15.3.1 Test of MS reaction to non-existent message type - CC protocol ................ 73

15.3.2 Test of MS reaction to message inconsistent with Call Control PD.............. 74

15.3.3 Test of MS reaction to message inconsistent with call state ........................ 74

15.4 Test of general information element errors....................................................................... 75

15.4.1 Test of MS response to duplicated Information Elements............................ 75

15.5 Test of MS reaction to mandatory information element errors.......................................... 76

15.5.1 Test of MS reaction to Mandatory Information Element errors in RR

message ....................................................................................................... 76

15.5.1.1 Test of MS reaction to Mandatory Information Element errors in RR

message - CHANNEL RELEASE ................................................................. 76

---------------------- Page: 6 ----------------------
SIST TBR 005:2000
Page 5
TBR 5: October 1995
15.5.1.2 Test of MS reaction to Mandatory Information Element errors in RR

message - CIPHER MODE COMMAND .......................................................76

15.5.2 Test of MS reaction to Mandatory Information Element errors in MM

message........................................................................................................77

15.5.3 Test of MS reaction to Mandatory information Element errors in CC

message........................................................................................................77

15.5.3.1 Test of MS reaction to Mandatory Information Element errors in CC

message - 1st case .......................................................................................77

15.5.3.2 Test of MS reaction to Mandatory Information Element errors in CC

message - 2nd case......................................................................................78

15.5.3.3 Test of MS reaction to Mandatory Information Element errors in CC

message - 3rd case.......................................................................................79

15.6 Test of MS reaction to non-mandatory information element errors ...................................79

15.6.1 Test of MS reaction to non-mandatory information element errors in RR

message........................................................................................................79

15.6.1.1 Test of MS reaction to unrecognized information element in RR message

on a dedicated control channel - comprehension required ...........................79

15.6.1.2 Test of MS reaction to unrecognized information element in RR message

on a dedicated control channel - comprehension not required .....................80

15.6.2 Test of MS reaction to non-mandatory information element errors in MM

message........................................................................................................80

15.6.2.1 Test of MS reaction to non-mandatory information element errors in MM

messages - comprehension required............................................................80

15.6.2.2 Test of MS reaction to non-mandatory information element errors in MM

messages - comprehension not required......................................................81

15.6.3 Test of MS reaction to non-mandatory information element errors in CC

message........................................................................................................82

15.6.3.1 Test of MS reaction to non-mandatory information element errors in CC

messages - 1st case .....................................................................................82

15.6.3.2 Test of MS reaction to non-mandatory information element errors in CC

messages - 2nd case ....................................................................................83

15.6.3.3 Test of MS reaction to non-mandatory information element errors in CC

messages - 3rd case.....................................................................................83

15.6.3.4 Test of MS reaction to non-mandatory information element errors in CC

messages - 4th case .....................................................................................84

15.6.3.5 Test of MS reaction to non-mandatory information element errors in CC

messages - 5th case .....................................................................................85

16 Elementary procedures for Radio Resource management...............................................................85

16.1 Immediate assignment.......................................................................................................85

16.1.1 Assignment procedure ..................................................................................85

16.1.2 Extended assignment....................................................................................86

16.1.3 Assignment rejection.....................................................................................88

16.1.4 Ignore assignment for another MS................................................................88

16.2 Test of paging ....................................................................................................................89

16.2.1 Normal paging...............................................................................................89

16.2.1.1 Paging request type 1....................................................................................89

16.2.1.2 Paging request type 2....................................................................................90

16.2.1.3 Paging request type 3....................................................................................92

16.2.1.4 MS with no more TMSI available...................................................................92

16.2.2 Extended paging ...........................................................................................93

16.2.3 Paging reorganisation ...................................................................................94

16.2.4 No change of page mode..............................................................................95

16.3 Measurement report ..........................................................................................................95

16.3.1 No neighbouring cells....................................................................................96

16.3.2 All neighbours present...................................................................................96

16.3.3 Combination of barred cells and un-permitted PLMNs .................................97

16.3.4 Use of DTX in the measurement report ........................................................97

16.4 Test of dedicated channel assignment ..............................................................................98

16.4.1 Assignment completion .................................................................................98

16.4.2 Assignment failure.......................................................................................100

16.5 Test of handover..............................................................................................................100

---------------------- Page: 7 ----------------------
SIST TBR 005:2000
Page 6
TBR 5: October 1995
16.5.1 Non synchronized handover during call in progress towards a TCH/F

without frequency hopping.......................................................................... 100

16.5.2 Non synchronized handover during call in progress, from a TCH/H without

frequency hopping to a TCH/H with frequency hopping ............................. 101

16.5.3 Non synchronized handover during call establishment from TCH/F with

frequency hopping to TCH/F with frequency hopping................................. 102

16.5.4 Non synchronized handover during call establishment from SDCCH with

frequency hopping to TCH/F without frequency hopping............................ 103

16.5.5 Synchronized handover during call in progress from TCH/F with frequency

hopping to TCH/F without frequency hopping ............................................ 105

16.5.6 Synchronized handover during call in progress from TCH/H with

frequency hopping to TCH/H without frequency hopping ........................... 105

16.5.7 Synchronized handover during call establishment from SDCCH with

frequency hopping to SDCCH with frequency hopping............................... 106

16.5.8 Synchronized handover during call establishment from TCH/F without

frequency hopping to TCH/F with frequency hopping................................. 108

16.5.9 Synchronized handover during call establishment from SDCCH without

frequency hopping to TCH/F without frequency hopping............................ 109

16.5.10 Layer 3 failure on the target cell during non synchronized handover
procedure from TCH/F with frequency hopping to TCH/F without

frequency hopping ...................................................................................... 110

16.5.11 Layer 1 failure on the target cell during non synchronized handover
procedure from TCH/F without frequency hopping to TCH/F with

frequency hopping ...................................................................................... 111

16.6 Frequency redefinition..................................................................................................... 111

16.7 Transmission mode change............................................................................................ 112

16.8 Ciphering mode setting ................................................................................................... 113

16.9 Classmark change .......................................................................................................... 114

16.10 Channel release .............................................................................................................. 115

16.11 Ciphering mode setting for MS supporting A5/2 ............................................................. 116

16.12 Classmark Interrogation.................................................................................................. 117

17 Elementary procedures of Mobility Management (MM)................................................................. 117

17.1 Test of TMSI reallocation procedure............................................................................... 117

17.2 Test of authentication procedure..................................................................................... 118

17.3 Test of identification procedure....................................................................................... 119

17.4 Test of location updating procedure................................................................................ 120

17.4.1 Location updating accepted........................................................................ 120

17.4.2 Location updating reject.............................................................................. 121

17.4.2.1 Location updating reject cause "IMSI unknown in HLR"............................. 121

17.4.2.2 Location updating reject cause "PLMN not allowed" .................................. 122

17.4.2.3 Location updating reject cause "Location area not allowed" ...................... 124

17.4.3 Abnormal cases during location updating procedure ................................. 125

17.4.3.1 Random access fails .................................................................................. 125

17.4.3.2 Attempt counter smaller than 4, stored LAI different from broadcast LAI... 126

17.4.3.3 Attempt counter greater or equal to 4, stored LAI different from broadcast

LAI .............................................................................................................. 128

17.4.3.4 Attempt counter smaller than 4, stored LAI equal to broadcast LAI ........... 130

17.4.4 Test of periodic updating ............................................................................ 132

17.5 MM connection establishment......................................................................................... 134

17.5.1 MM connection establishment with cipher mode setting ............................ 134

17.5.2 MM connection establishment rejected with cause "IMSI unknown in VLR"134

18 Tests related to circuit switched Call Control (CC) ......................................................................... 135

18.1 Circuit switched Call Control state machine.................................................................... 135

18.1.1 Establishment of an outgoing call............................................................... 135

18.1.1.1 U0 null state................................................................................................ 135

18.1.1.2 U0.1 MM connection pending ..................................................................... 136

18.1.1.2.1 U0.1 MM connection pending - 1st case .................................................... 136

18.1.1.2.2 U0.1 MM connection pending - 2nd case ................................................... 136

18.1.1.2.3 U0.1 MM connection pending - 3rd case.................................................... 137

18.1.1.3 U1 call initiated............................................................................................ 138

18.1.1.3.1 U1 call initiated - 1st case........................................................................... 138

---------------------- Page: 8 ----------------------
SIST TBR 005:2000
Page 7
TBR 5: October 1995

18.1.1.3.2 U1 call initiated - second case.....................................................................138

18.1.1.3.3 U1 call initiated - 3rd case ...........................................................................139

18.1.1.3.4 U1 call initiated - 4th case ...........................................................................139

18.1.1.3.5 U1 call initiated - 5th case ...........................................................................140

18.1.1.3.6 U1 call initiated - 6th case ...........................................................................141

18.1.1.3.7 U1 call initiated - 7th case ...........................................................................141

18.1.1.4 U3 MS originating call proceeding...............................................................142

18.1.1.4.1 U3 MS originating call proceeding - first case............................................142

18.1.1.4.2 U3 MS originating call proceeding - 2nd case............................................142

18.1.1.4.3 U3 MS originating call proceeding - 3rd case.............................................143

18.1.1.4.4 U3 MS originating call proceeding - 4th case.............................................144

18.1.1.4.5 U3 MS originating call proceeding - 5th case.............................................144

18.1.1.4.6 U3 MS originating call proceeding - 6th case.............................................145

18.1.1.4.7 U3 MS originating call proceeding - 7th case.............................................146

18.1.1.4.8 U3 MS originating call proceeding - 8th case.............................................146

18.1.1.4.9 U3 MS originating call proceeding - 9th case.............................................147

18.1.1.4.10 U3 MS originating call proceeding - 10th case...........................................147

18.1.1.4.11 U3 MS originating call proceeding - 11th case...........................................148

18.1.1.5 U4 call delivered..........................................................................................149

18.1.1.5.1 U4 call delivered - 1st case .......................................................................149

18.1.1.5.2 U4 call delivered - 2nd case ......................................................................149

18.1.1.5.3 U4 call delivered - 3rd case.......................................................................150

18.1.1.5.4 U4 call delivered - 4th case .......................................................................150

18.1.1.5.5 U4 call delivered - 5th case .......................................................................151

18.1.1.5.6 U4 call
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.