SIST EN 300 338-6 V1.1.1:2017
(Main)Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 6: Class M DSC
Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 6: Class M DSC
The present document states the minimum requirements for devices using Digital Selective Calling (DSC) Class M, for
Man Overboard (MOB). The present document defines the requirements for equipment that uses DSC alerting and
signalling in the maritime mobile bands and particularly the GMDSS distress and safety channels. Such equipment is
not intended to provide any subsequent communications or telephony facilities.
The present document is part 6 of a multi-part deliverable that covers the channel access rules and technical
requirements applicable to these devices.
Tehnične karakteristike in merilne metode za naprave, ki generirajo, oddajajo in sprejemajo digitalni selektivni klic (DSC) v pomorski mobilni storitvi, ki deluje v območju MF, MF/HF oziroma VHF - 6. del: Digitalni selektivni klic razreda M
V tem dokumentu so navedene minimalne zahteve za naprave, ki uporabljajo digitalno selektivno klicanje razreda M za pomoč pri padcu človeka v vodo (MOB). Ta dokument določa zahteve za opremo, ki uporablja digitalno selektivno klicanje za opozarjanje in pošiljanje signalov v pasovih pomorske mobilne storitve ter zlasti za zasilne in varnostne kanale Mednarodne konvencije o varstvu človeškega življenja na morju. Namen takšnih naprav ni zagotavljanje naknadne komunikacije ali telefonije. Ta dokument je 6. del večdelnega dokumenta, ki obravnava pravila glede dostopa do kanalov in tehnične zahteve za takšne naprave.
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 300 338-6 V1.1.1 (2017-02)
EUROPEAN STANDARD
Technical characteristics and methods of measurement
for equipment for generation, transmission
and reception of Digital Selective Calling (DSC)
in the maritime MF, MF/HF and/or VHF mobile service;
Part 6: Class M DSC
---------------------- Page: 1 ----------------------
2 ETSI EN 300 338-6 V1.1.1 (2017-02)
Reference
DEN/ERM-TG26-087-6
Keywords
DSC, GMDSS, maritime, radio, SAR
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 338-6 V1.1.1 (2017-02)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definitions and abbreviations . 6
3.1 Definitions . 6
3.2 Abbreviations . 6
4 General requirements . 7
4.1 General . 7
4.2 Frequency of operation . 7
4.3 Class of emission . 7
4.4 Controls . 7
4.5 Indicators . 8
4.5.0 General . 8
4.5.1 Audible indicators . 8
4.5.2 Visual Indicators . 8
4.6 Labelling. 8
4.7 Instructions . 9
4.8 Self ID . 9
4.9 Own vessel MMSI . 9
4.10 Battery requirement . 9
5 DSC Operation . 9
5.1 Listen Before Talk (LBT) Protocol . 9
5.1.0 General . 9
5.1.1 Active Mode Wait Period Calculation . 10
5.1.2 Test Mode Wait Period Calculation . 10
5.2 DSC messages . 10
5.2.1 Active mode . 10
5.2.1.0 General . 10
5.2.1.1 Closed loop operation . 10
5.2.1.2 Open loop operation . 11
5.2.1.3 Distress self cancel . 11
5.2.2 Test mode. 11
5.3 Action on receipt of acknowledgment messages to alerts . 12
6 Internal electronic position fixing device . 12
History . 13
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 338-6 V1.1.1 (2017-02)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and
Radio spectrum Matters (ERM).
The present document is part 6 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.1].
National transposition dates
Date of adoption of this EN: 8 February 2017
Date of latest announcement of this EN (doa): 31 May 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2017
Date of withdrawal of any conflicting National Standard (dow): 30 November 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 338-6 V1.1.1 (2017-02)
1 Scope
The present document states the minimum requirements for devices using Digital Selective Calling (DSC) Class M, for
Man Overboard (MOB). The present document defines the requirements for equipment that uses DSC alerting and
signalling in the maritime mobile bands and particularly the GMDSS distress and safety channels. Such equipment is
not intended to provide any subsequent communications or telephony facilities.
The present document is part 6 of a multi-part deliverable that covers the channel access rules and technical
requirements applicable to these devices.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R M.493-14: "Digital selective-calling system for use in the maritime
mobile service".
[2] ETSI EN 303 098: "Maritime low power personal locating devices employing AIS; Harmonised
Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU".
[3] Recommendation ITU-R M.585-7: "Assignment and use of identities in the maritime mobile
service".
[4] Recommendation ITU-R M.821-1: "Optional expansion of the digital selective-calling system for
use in the maritime mobile service".
[5] CENELEC EN 61108-1: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 1: Global positioning system (GPS) - Receiver
equipment - Performance standards, methods of testing and required test results".
[6] CENELEC EN 61108-2: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 2: Global navigation satellite system
(GLONASS) - Receiver equipment - Performance standards, methods of testing and required test
results".
[7] CENELEC EN 61108-3: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 3: Galileo receiver equipment - Performance
requirements, methods of testing and required test results".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 338-6 V1.1.1 (2017-02)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 300 338-1: "Technical characteristics and methods of measurement for equipment for
generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF,
MF/HF and/or VHF mobile service; Part 1: Common requirements".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 300 338-1 [i.1] and the following
apply:
acknowledged: automated procedure it indicates that the objective of the initial DSC message has been achieved
activation: initial triggering of the MoB device i.e. both parts of the two step procedure are performed
active mode: activated mode, transmitting in an emergency situation
class M: specific class of DSC functionality for use by man overboard devices
closed loop: individual transmission to own vessel
default: value selected or an action taken by the equipment software in the absence of any operator input
distress alert: name given to the single distress DSC message with the format symbol 112
distress DSC message: DSC message or acknowledgement containing the distress information
distress information: symbols within a DSC message describing a distress situation consisting of the MMSI of the
vessel in distress, the nature of distress, the position of the vessel in distress, the UTC time of that position and the mode
of subsequent communication
factory default: default value that is set by the manufacturer such that the field or behaviour is defined prior to any
operator intervention
information characters: set of symbols in a DSC message that contains the items of interest for the recipient and is
used to compute the ECC symbol that terminates the message
non distress DSC message: DSC messages or acknowledgements that do not have the format specifier or category of
"distress"
open loop: transmitting to all ships (broadcast) 'using All ships call types'
symbol (as part of the DSC sentence): 7 binary bits of a 10 bit DSC word that have the information content
test mode: self testing mode using an individual test call to own vessel
word (as part of the DSC sentence): 10 binary bits that make up the coded entities of a transmitted DSC message
NOTE: The 10 bits consist of a 7 bit "symbol" that gives the information content and 3 bit error check that gives
the number of 0 binary bits in the 7 bit symbol.
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AIS Automatic Identification System
CIRM Comite International Radio-Maritime
DSC Digital Selective Calling
ECC Error Check Character
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 300 338-6 V1.1.1 (2017-02)
GMDSS Global Maritime Distress and Safety System
GMSK Gaussian Minimum Shift Keying
GNSS Global Navigation Satellite System
GPS Global Positioning System
HF High Frequency
ID IDentity
ITU International Telecommunications Union
ITU-R ITU - Radiocommunications Sector
LBT Listen Before Talk
MF Medium Frequency
MMSI Maritime Mobile Service Identity
MOB Man Overboard
PM Phase Modulation
UTC Universal Time Co-ordinated
VHF Very High Frequency
WGS World Geodetic System
4 General requirements
4.1 General
Class M MOB devices are employed in situations of grave and imminent danger to persons that require immediate
assist
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service - Part 6: Class M DSC47.020.70Navigacijska in krmilna opremaNavigation and control equipment33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 300 338-6 V1.1.1 (2017-02)SIST EN 300 338-6 V1.1.1:2017en01-april-2017SIST EN 300 338-6 V1.1.1:2017SLOVENSKI
STANDARD
SIST EN 300 338-6 V1.1.1:2017
ETSI EN 300 338-6 V1.1.1 (2017-02) Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 6: Class M DSC
EUROPEAN STANDARD SIST EN 300 338-6 V1.1.1:2017
ETSI ETSI EN 300 338-6 V1.1.1 (2017-02) 2
Reference DEN/ERM-TG26-087-6 Keywords DSC, GMDSS, maritime, radio, SAR ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 338-6 V1.1.1:2017
ETSI ETSI EN 300 338-6 V1.1.1 (2017-02) 3 Contents Intellectual Property Rights . 4 Foreword . 4 Modal verbs terminology . 4 1 Scope . 5 2 References . 5 2.1 Normative references . 5 2.2 Informative references . 5 3 Definitions and abbreviations . 6 3.1 Definitions . 6 3.2 Abbreviations . 6 4 General requirements . 7 4.1 General . 7 4.2 Frequency of operation . 7 4.3 Class of emission . 7 4.4 Controls . 7 4.5 Indicators . 8 4.5.0 General . 8 4.5.1 Audible indicators . 8 4.5.2 Visual Indicators . 8 4.6 Labelling. 8 4.7 Instructions . 9 4.8 Self ID . 9 4.9 Own vessel MMSI . 9 4.10 Battery requirement . 9 5 DSC Operation . 9 5.1 Listen Before Talk (LBT) Protocol . 9 5.1.0 General . 9 5.1.1 Active Mode Wait Period Calculation . 10 5.1.2 Test Mode Wait Period Calculation . 10 5.2 DSC messages . 10 5.2.1 Active mode . 10 5.2.1.0 General . 10 5.2.1.1 Closed loop operation . 10 5.2.1.2 Open loop operation . 11 5.2.1.3 Distress self cancel . 11 5.2.2 Test mode. 11 5.3 Action on receipt of acknowledgment messages to alerts . 12 6 Internal electronic position fixing device . 12 History . 13
SIST EN 300 338-6 V1.1.1:2017
ETSI ETSI EN 300 338-6 V1.1.1 (2017-02) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 6 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.1].
National transposition dates Date of adoption of this EN: 8 February 2017 Date of latest announcement of this EN (doa): 31 May 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 November 2017 Date of withdrawal of any conflicting National Standard (dow): 30 November 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
SIST EN 300 338-6 V1.1.1:2017
ETSI ETSI EN 300 338-6 V1.1.1 (2017-02) 5 1 Scope The present document states the minimum requirements for devices using Digital Selective Calling (DSC) Class M, for Man Overboard (MOB). The present document defines the requirements for equipment that uses DSC alerting and signalling in the maritime mobile bands and particularly the GMDSS distress and safety channels. Such equipment is not intended to provide any subsequent communications or telephony facilities. The present document is part 6 of a multi-part deliverable that covers the channel access rules and technical requirements applicable to these devices. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] Recommendation ITU-R M.493-14: "Digital selective-calling system for use in the maritime mobile service". [2] ETSI EN 303 098: "Maritime low power personal locating devices employing AIS; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU". [3] Recommendation ITU-R M.585-7: "Assignment and use of identities in the maritime mobile service". [4] Recommendation ITU-R M.821-1: "Optional expansion of the digital selective-calling system for use in the maritime mobile service". [5] CENELEC EN 61108-1: "Maritime navigation and radiocommunication equipment and systems - Global navigation satellite systems (GNSS) - Part 1: Global positioning system (GPS) - Receiver equipment - Performance standards, methods of testing and required test results". [6] CENELEC EN 61108-2: "Maritime navigation and radiocommunication equipment and systems - Global navigation satellite systems (GNSS) - Part 2: Global navigation satellite system (GLONASS) - Receiver equipment - Performance standards, methods of testing and required test results". [7] CENELEC EN 61108-3: "Maritime navigation and radiocommunication equipment and systems - Global navigation satellite systems (GNSS) - Part 3: Galileo receiver equipment - Performance requirements, methods of testing and required test results". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. SIST EN 300 338-6 V1.1.1:2017
ETSI ETSI EN 300 338-6 V1.1.1 (2017-02) 6 The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] ETSI EN 300 338-1: "Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 1: Common requirements". 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 300 338-1 [i.1] and the following apply: acknowledged: automated procedure it indicates that the objective of the initial DSC message has been achieved activation: initial triggering of the MoB device i.e. both parts of the two step procedure are performed active mode: activated mode, transmitting in an emergency situation class M: specific class of DSC functionality for use by man overboard devices closed loop: individual transmission to own vessel
default: value selected or an action taken by the equipment software in the absence of any operator input distress alert: name given to the single distress DSC message with the format symbol 112 distress DSC message: DSC message or acknowledgement containing the distress information distress information: symbols within a DSC message describing a distress situation consisting of the MMSI of the vessel in distress, the nature of distress, the position of the vessel in distress, the UTC time of that position and the mode of subsequent communication factory default: default value that is set by the manufacturer such that the field or behaviour is defined prior to any operator intervention information characters: set of symbols in a DSC message that contains the items of interest for the recipient and is used to compute the ECC symbol that terminates the message non distress DSC message: DSC messages or acknowledgements that do not have the format specifier or category of "distress" open loop: transmitting to all ships (broadcast) 'using All ships call types' symbol (as part of the DSC sentence): 7 binary bits of a 10 bit DSC word that have the information content test mode: self testing mode using an individual test call to own vessel word (as part of the DSC sentence): 10 binary bits that make up the coded entities of a transmitted DSC message NOTE: The 10 bits consist of a 7 bit "symbol" that gives the information content and 3 bit error check that gives the number of 0 binary bits in the 7 bit symbol. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AIS Automatic Identification System CIRM Comite International Radio-Maritime DSC Digital Selective Calling ECC Error Check Character SIST EN 300 338-6 V1.1.1:2017
ETSI ETSI EN 300 338-6 V1.1.1 (2017-02) 7 GMDSS Global Maritime Distress and Safety System GMSK Gaussian Minimum Shift Keying GNSS Global Navigation Satellite System GPS Global Positioning System HF High Frequency ID IDentity ITU International Telecommunications Union ITU-R ITU - Radiocommunications Sector LBT Listen
...
Draft ETSI EN 300 338-6 V1.1.0 (2016-11)
EUROPEAN STANDARD
Technical characteristics and methods of measurement
for equipment for generation, transmission
and reception of Digital Selective Calling (DSC)
in the maritime MF, MF/HF and/or VHF mobile service;
Part 6: Class M DSC
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 338-6 V1.1.0 (2016-11)
Reference
DEN/ERM-TG26-087-6
Keywords
DSC, GMDSS, maritime, radio, SAR
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 338-6 V1.1.0 (2016-11)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definitions and abbreviations . 6
3.1 Definitions . 6
3.2 Abbreviations . 6
4 General requirements . 7
4.1 General . 7
4.2 Frequency of operation . 7
4.3 Class of emission . 7
4.4 Controls . 7
4.5 Indicators . 8
4.5.0 General . 8
4.5.1 Audible indicators . 8
4.5.2 Visual Indicators . 8
4.6 Labelling. 8
4.7 Instructions . 9
4.8 Self ID . 9
4.9 Own vessel MMSI . 9
4.10 Battery requirement . 9
5 DSC Operation . 9
5.1 Listen Before Talk (LBT) Protocol . 9
5.1.0 General . 9
5.1.1 Active Mode Wait Period Calculation . 10
5.1.2 Test Mode Wait Period Calculation . 10
5.2 DSC messages . 10
5.2.1 Active mode . 10
5.2.1.0 General . 10
5.2.1.1 Closed loop operation . 10
5.2.1.2 Open loop operation . 11
5.2.1.3 Distress self cancel . 11
5.2.2 Test mode. 11
5.3 Action on receipt of acknowledgment messages to alerts . 12
6 Internal electronic position fixing device . 12
History . 13
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 338-6 V1.1.0 (2016-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility
and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document is part 6 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.1].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 338-6 V1.1.0 (2016-11)
1 Scope
The present document states the minimum requirements for devices using Digital Selective Calling (DSC) Class M, for
Man Overboard (MOB). The present document defines the requirements for equipment that uses DSC alerting and
signalling in the maritime mobile bands and particularly the GMDSS distress and safety channels. Such equipment is
not intended to provide any subsequent communications or telephony facilities.
The present document is part 6 of a multi-part deliverable that covers the channel access rules and technical
requirements applicable to these devices.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] Recommendation ITU-R M.493-14: "Digital selective-calling system for use in the maritime
mobile service".
[2] ETSI EN 303 098: "Maritime low power personal locating devices employing AIS; Harmonised
Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU".
[3] Recommendation ITU-R M.585-7: "Assignment and use of identities in the maritime mobile
service".
[4] Recommendation ITU-R M.821-1: "Optional expansion of the digital selective-calling system for
use in the maritime mobile service".
[5] CENELEC EN 61108-1: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 1: Global positioning system (GPS) - Receiver
equipment - Performance standards, methods of testing and required test results".
[6] CENELEC EN 61108-2: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 2: Global navigation satellite system
(GLONASS) - Receiver equipment - Performance standards, methods of testing and required test
results".
[7] CENELEC EN 61108-3: "Maritime navigation and radiocommunication equipment and systems -
Global navigation satellite systems (GNSS) - Part 3: Galileo receiver equipment - Performance
requirements, methods of testing and required test results".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 338-6 V1.1.0 (2016-11)
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 300 338-1: "Technical characteristics and methods of measurement for equipment for
generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF,
MF/HF and/or VHF mobile service; Part 1: Common requirements".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 300 338-1 [i.1] and the following
apply:
acknowledged: automated procedure it indicates that the objective of the initial DSC message has been achieved
activation: initial triggering of the MoB device i.e. both parts of the two step procedure are performed
active mode: activated mode, transmitting in an emergency situation
class M: specific class of DSC functionality for use by man overboard devices
closed loop: individual transmission to own vessel
default: value selected or an action taken by the equipment software in the absence of any operator input
distress alert: name given to the single distress DSC message with the format symbol 112
distress DSC message: DSC message or acknowledgement containing the distress information
distress information: symbols within a DSC message describing a distress situation consisting of the MMSI of the
vessel in distress, the nature of distress, the position of the vessel in distress, the UTC time of that position and the mode
of subsequent communication
factory default: default value that is set by the manufacturer such that the field or behaviour is defined prior to any
operator intervention
information characters: set of symbols in a DSC message that contains the items of interest for the recipient and is
used to compute the ECC symbol that terminates the message
non distress DSC message: DSC messages or acknowledgements that do not have the format specifier or category of
"distress"
open loop: transmitting to all ships (broadcast) 'using All ships call types'
symbol (as part of the DSC sentence): 7 binary bits of a 10 bit DSC word that have the information content
test mode: self testing mode using an individual test call to own vessel
word (as part of the DSC sentence): 10 binary bits that make up the coded entities of a transmitted DSC message
NOTE: The 10 bits consist of a 7 bit "symbol" that gives the information content and 3 bit error check that gives
the number of 0 binary bits in the 7 bit symbol.
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AIS Automatic Identification System
CIRM Comite International Radio-Maritime
DSC Digital Selective Calling
ECC Error Check Character
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 300 338-6 V1.1.0 (2016-11)
GMDSS Global Maritime Distress and Safety System
GMSK Gaussian Minimum Shift Keying
GNSS Global Navigation Satellite System
GPS Global Positioning System
HF High Frequency
ID IDentity
ITU International Telecommunications Union
ITU-R ITU - Radiocommunications Sector
LBT Listen Before Talk
MF Medium Frequency
MMSI Maritime Mobile Service Identity
MOB Man Overboard
PM Phase Modulation
UTC Universal Time Co-ordinated
VHF Very High Frequency
WGS World Geodetic System
4 General requirements
4.1 General
Class M MOB devices are employed in situation
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.