SIST EN 972:2000/kprA1:2010
(Amendment)Tannery machines - Reciprocating roller machines - Safety requirements
Tannery machines - Reciprocating roller machines - Safety requirements
2009-12-11: WI activated due to delivery of the text.
2009-12-10: OD WI deleted Alert 2
2009-09-09 SJ: Under Alert 2 - can be deleted if no text by end November 2009.
Type 1 amendment.
Gerberei-Maschinen - Walzenmaschinen - Sicherheitsanforderungen
Machines de tannerie - Machines à cylindres alternatifs - Prescriptions de sécurité
Strojarski stroji - Valjčni stroji - Varnostne zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 972:2000/kprA1:2010
01-september-2010
6WURMDUVNLVWURML9DOMþQLVWURML9DUQRVWQH]DKWHYH
Tannery machines - Reciprocating roller machines - Safety requirements
Gerberei-Maschinen - Walzenmaschinen - Sicherheitsanforderungen
Machines de tannerie - Machines à cylindres alternatifs - Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 972:1998/FprA1
ICS:
59.140.40 Stroji in oprema za Machines and equipment for
proizvodnjo usnja in krzna leather and fur production
SIST EN 972:2000/kprA1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 972:2000/kprA1:2010
---------------------- Page: 2 ----------------------
SIST EN 972:2000/kprA1:2010
EUROPEAN STANDARD
FINAL DRAFT
EN 972:1998
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
May 2010
ICS 59.140.40
English Version
Tannery machines - Reciprocating roller machines - Safety
requirements
Machines de tannerie - Machines à cylindres alternatifs - Gerberei-Maschinen - Walzenmaschinen -
Prescriptions de sécurité Sicherheitsanforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 200.
This draft amendment A1, if approved, will modify the European Standard EN 972:1998. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 972:1998/FprA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 972:2000/kprA1:2010
EN 972:1998/FprA1:2010 (E)
Foreword
This document (EN 972:1998/FprA1:2010) has been prepared by Technical Committee CEN/TC 200 “Tannery
machinery - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
The first reason for amending the published standard EN 972:1998 is the revision of the EU-Machinery
Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European Standards cited in the
Official Journal of the European Communities under that Directive.
Additionally at this occasion the normative references have been updated, while also some other limited rather
editorial improvements and corrections have been made.
2
---------------------- Page: 4 ----------------------
SIST EN 972:2000/kprA1:2010
EN 972:1998/FprA1:2010 (E)
1 Modification to the Introduction
Replace the complete text with the following:
"This document is a type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are
covered are indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.".
2 Modifications to Clause 1, Scope
st
Replace the following text in the 1 paragraph “3.11 a) of EN 292-1:1991” with “5.3 a) of
EN ISO 12100-1:2003”.
th
Replace the 5 paragraph “This European Standard applies to the machine manufactured after its date of
issue.” with the following: "This European Standard is not applicable to reciprocating roller machines which
are manufactured before the date of its publication as EN.".
th
Add the following paragraph after the 5 paragraph “This European Standard provides provisions for the
reduction of noise emission at the design stage (see 5.2.4 and Annex A). However, it does not provide a noise
test code for the determination by measurement of noise emission values for the machines it covers. Without
such a code the manufacturer cannot fulfil his obligation to provide the noise emission values of the machines
put on the market.”.
th
Replace the following text in the 6 paragraph “All the significant hazard listed in clause 4 are safeguarded by
the requirements included in clause 5 except the following:” with “All the significant hazards (see Clause 4) are
dealt with in this European Standard except the following:”.
Replace the following text in the last paragraph “informative annexes” with “normative annexes”.
3 Modifications to Clause 2, Normative references
Introductory text: Replace the first paragraph with the following: "The following referenced documents are
indispensable for the application of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.".
EN 292-1: Delete this reference and add the following: "EN ISO 12100-1:2003, Safety of machinery — Basic
concepts, general principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003)".
EN 292-2: Delete this reference and add the following: "EN ISO 12100-2:2003, Safety of machinery — Basic
concepts, general principles for design — Part 2: Technical principles (ISO 12100-2:2003)".
Add the reference: “EN 388:2003, Protective gloves against mechanical risks”.
EN 294: Delete this reference and add the following: "EN ISO 13857:2008, Safety of machinery — Safety
distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)".
3
---------------------- Page: 5 ----------------------
SIST EN 972:2000/kprA1:2010
EN 972:1998/FprA1:2010 (E)
EN 418: Delete this reference and add the following: "EN ISO 13850:2008, Safety of machinery — Emergency
stop — Principles for design (ISO 13850:2006)".
EN 563: Delete this reference and add the following: "EN ISO 13732-1:2008, Ergonomics of the thermal
environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot
surfaces (ISO 13732-1:2006)”.
Delete reference EN 811.
EN 954-1: Delete this reference and add the following: "EN ISO 13849-1:2008, Safety of machinery — Safety-
related parts of control systems — Part 1: General principles for design (ISO 13849-1:2006)".
prEN 999: Replace this reference with the following: "EN 999:1998, Safety of machinery — The positioning of
protective equipment in respect of approach speeds of parts of the human body".
EN 1037: Replace this reference with the following: "EN 1037:1995 Safety of machinery — Prevention of
unexpected start-up”.
Delete reference EN 1070.
EN 1760-2: Replace this reference with the following: "EN 1760-2:2001, Safety of machinery — Pressure
sensitive protective devices — Part 2: General principles for the design and testing of pressure sensitive
edges and pressure sensitive bars”.
Delete reference prEN ISO 3740.
Delete reference EN ISO 11200.
prEN 50100-1: Delete this reference and add the following: "EN 61496-1:2004, Safety of machinery —
Electro-sensitive protective equipment — Part 1: General requirements and tests (IEC 61496-1:2004,
modified)".
prEN 50100-2: Delete this reference and the following: "CLC/TS 61496-2:2006, Safety of machinery —
Electro-sensitive protective equipment — Particular requirements for equipment using active optoelectronic
protective devices (AOPDs) (IEC 61496-2:2006)".
EN 60204-1: Replace this reference with the following: "EN 60204-1:2006, Safety of machinery — Electrical
equipment of machines — Part 1: General requirements (IEC 60204-1:2005, modified)".
EN 60529: Replace this item with the following: "EN 60529:1991, Degrees of protection provided by
enclosures (IP code) (IEC 60529:1989)”.
EN 61310-1: Add the following reference: "EN 61310-1:2008, Safety of machinery — Indication, marking and
actuation — Part 1: Requirements for visual, acoustic and tactile signals (IEC 61310-1:2007)".
Delete all full stops at the end of reference titles.
4 Modifications to Clause 3, Definitions
Replace the heading of this clause with the following: “Terms and definitions”.
Replace the introductory text with the following: "For the purposes of this document, the terms and definitions
given in EN ISO 12100-1:2003 and the following apply.".
3.2:
Replace the heading with the following: "Danger zones (as 3.10 of EN ISO 12100-1:2003)”.
4
---------------------- Page: 6 ----------------------
SIST EN 972:2000/kprA1:2010
EN 972:1998/FprA1:2010 (E)
5 Modification to Clause 4, List of significant hazards
Introductory paragraph: replace the text with the following:
"This clause contains all the significant hazards, hazardous situations and events, as far as they are dealt with
in this European Standard, identified by risk assessment as significant for this type of machinery and which
require action to eliminate or reduce the risk.
The significant hazards for moving platen machines are outlined in 4.1 to 4.18.
The danger zones which give rise to mechanical hazards are illustrated in Figures 1 to 13. The figures are
informative only.".
6 Modifications to Clause 5, Safety requirements and/or measures
Replace the heading with the following: "Safety requirements and/or protective measures”.
Replace the hanging paragraphs with the following:
"Machinery shall comply with the safety requirements and/or protective measures of this clause.
In addition, the machine shall be designed according to the principles of EN ISO 12100-2 for relevant but not
significant hazards which are not dealt with by this document.
For hazards which are to be reduced by the application of a type B-standard such as EN 13857, EN 953,
EN ISO 13850, EN 60204-1 etc., the manufacturer shall carry out a risk assessment to establish the
requirements of the B-standards which are to be applied.".
5.1 Common requirements
Replace the heading with the following: "Common requirements concerning reciprocating roller machines”.
5.1.1
st
Replace the following text in the 1 indent "EN 953:1997 and 4.2.2.2 of EN 292-2:1991" with "EN 953 and
5.3.2.2 of EN ISO 12100-2:2003".
nd
Replace the following text in the 2 indent "EN 953:1997, EN 1088:1995 and 4.2.2.2 of EN 292-2:1991" with
"EN 953, EN 1088 and 5.3.2.3 of EN ISO 12100-2:2003".
rd
Replace the following text in the 3 indent "EN 953:1997 and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.