SIST EN ISO 5366-1:2005
(Main)Anaesthetic and respiratory equipment - Tracheostomy tubes - Part 1: Tubes and connectors for use in adults (ISO 5366-1:2000)
Anaesthetic and respiratory equipment - Tracheostomy tubes - Part 1: Tubes and connectors for use in adults (ISO 5366-1:2000)
Anästhesie- und Beatmungsgeräte - Tracheotomietuben - Teil 1: Tuben und Verbindungsstücke zur Anwendung bei Erwachsenen (ISO 5366-1:2000)
Matériel d'anesthésie et de réanimation respiratoire - Tube de trachéostomie - Partie 1: Tubes et raccords pour adultes (ISO 5366-1:2000)
Anestezijska in dihalna oprema – Traheostomske cevke – 1. del: Cevke in priključki za odrasle (ISO 5366-1:2000)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 5366-1:2005
01-januar-2005
1DGRPHãþD
SIST EN 1282-1:2000
$QHVWH]LMVNDLQGLKDOQDRSUHPD±7UDKHRVWRPVNHFHYNH±GHO &HYNHLQ
SULNOMXþNL]DRGUDVOH ,62
Anaesthetic and respiratory equipment - Tracheostomy tubes - Part 1: Tubes and
connectors for use in adults (ISO 5366-1:2000)
Anästhesie- und Beatmungsgeräte - Tracheotomietuben - Teil 1: Tuben und
Verbindungsstücke zur Anwendung bei Erwachsenen (ISO 5366-1:2000)
Matériel d'anesthésie et de réanimation respiratoire - Tube de trachéostomie - Partie 1:
Tubes et raccords pour adultes (ISO 5366-1:2000)
Ta slovenski standard je istoveten z: EN ISO 5366-1:2004
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
SIST EN ISO 5366-1:2005 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 5366-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2004
ICS 11.040.10 Supersedes EN 1282-1:1996
English version
Anaesthetic and respiratory equipment - Tracheostomy tubes -
Part 1: Tubes and connectors for use in adults (ISO 5366-
1:2000)
Matériel d'anesthésie et de réanimation respiratoire - Tube Anästhesie- und Beatmungsgeräte - Tracheotomietuben -
de trachéostomie - Partie 1: Tubes et raccords pour adultes Teil 1: Tuben und Verbindungsstücke zur Anwendugn bei
(ISO 5366-1:2000) Erwachsenen (ISO 5366-1:2000, korrigiert und neu
gedruckt im Jahre 2001)
This European Standard was approved by CEN on 21 June 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5366-1:2004: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 5366-1:2004 (E)
Foreword
The text of ISO 5366-1:2000 has been prepared by Technical Committee ISO/TC 121
"Anaesthetic and respiratory equipment” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 5366-1:2004 by Technical Committee CEN/TC 215
"Respiratory and anaesthetic equipment", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2005, and conflicting national
standards shall be withdrawn at the latest by January 2005.
This document supersedes EN 1282-1:1996.
This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU
Directive(s).
For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 5366-1:2000 has been approved by CEN as EN ISO 5366-1:2004 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2
---------------------- Page: 3 ----------------------
EN ISO 5366-1:2004 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated by (mod.),
the relevant EN/HD applies.
Publication Year Title EN Year
ISO 594-1 1986 Conical fitings with a 6 % (Luer) taper EN 20594-1 1993
for syringes, needles and certain
other medical equipment – Part 1:
General requirements
ISO 4135 2001 Anaesthetic and respiratory EN ISO 4135 2001
equipment - Vocabulary
ISO 10993-1 1997 Biological evaluation of medical EN ISO 10993-1 1997
devices - Part 1: Evaluation and
testing
3
---------------------- Page: 4 ----------------------
EN ISO 5366-1:2004 (E)
Annex ZB
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 93/42 EEC
This European Standard has been prepared under a mandate given to CEN by the European
Commission and the European Free Trade Association to provide a means of conforming to
Essential Requirements of the New Approach Directive 93/42 EEC.
Once this standard is cited in the Official Journal of the European Communities under that
Directive and has been implemented as a national standard in at least one Member State,
compliance with the normative clauses of this standard given in Table ZB.1 confers, within the
limits of the scope of this standard, a presumption of conformity with the corresponding Essential
Requirements of that Directive and associated EFTA regulations.
WARNING: Other requirements and other EU Directives may be applicable to the product(s)
falling within the scope of this standard.
TABLE ZB.1 - Correspondence between this European Standard and EU
Directives
Clause/subclause of this Corresponding Essential Comments
European Standard Requirement of Directive
93/42/EEC
1 N/A
2 N/A
3 N/A
4 1, 2 a), 3
5 1, 2 a), 3, 7.1 a), 7.1 b), 7.2
6 1, 2, 3, 9.2 a)
6.1 4, 9.1, 9.3
6.1.1 7.5
6.1.4 7.5
6.2 4
6.3 9.1, 9.3
6.4.1 4
6.4.2 4
6.5.2.1 2 b)
6.5.3 9.1
6.7 4
7.1 8.1, 8.3, 8.4
4
---------------------- Page: 5 ----------------------
EN ISO 5366-1:2004 (E)
7.2.2 5, 8.1, 8.3
8.1 13.2, 13.3 g) – m), 13.4
8.2 13.1
8.2.1 a) 13.3 b)
8.2.1 b) 13.3 b), 2 c)
8.2.1 c) 13.3 a)
8.3 13.1, 13.3 e)
8.3.1 13.2
8.3.2 a) 13.3 b), 13.4
8.3.2 b) 13.3 b)
8.3.2 d) 13.3 b)
8.3.2 e) 13.3 b)
8.3.2 f) 13.3 b)
8.3.2 g) 13.3 a)
8.3.2 h) 13.3 d), 13.5
8.3.2 i) 8.6, 13.6 h)
8.3.2 j) 8.1, 8.3, 8.7, 13.2, 13.3 b), c)
8.3.2 k) 13.3 b)
8.3.2 l) 2 c), 13.3 b)
8.3.3 13.3 e)
8.3.3 a) 13.3 b), 13.4
8.3.3 b) 13.3 b)
8.3.3 c) 13.3 b)
8.3.3 d) 13.3 a)
8.3.3 e) 13.3 d), 13.5
8.3.3 f) 8.6, 13.6 h)
8.3.3 g) 8.1, 8.3, 8.7, 13.2, 13.3 b), c)
8.3.3 h) 13.3 b), d) – f), 13.5
Annex C 4, 7.1 b), 7.3, 9.2 a)
C.1.2 13.6 h)
C.1.3 9.3
N/A = not applicable
5
---------------------- Page: 6 ----------------------
INTERNATIONAL ISO
STANDARD 5366-1
Fourth edition
2000-12-15
Corrected and reprinted
2001-09-01
Anaesthetic and respiratory equipment —
Tracheostomy tubes —
Part 1:
Tubes and connectors for use in adults
Matériel d'anesthésie et de réanimation respiratoire — Tubes de
trachéostomie —
Partie 1: Tubes et raccords pour adultes
Reference number
ISO 5366-1:2000(E)
© ISO 2000
---------------------- Page: 7 ----------------------
ISO 5366-1:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec-
tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's mem-
ber body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2000 – All rights reserved
---------------------- Page: 8 ----------------------
ISO 5366-1:2000(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Size designation and dimensions . 4
5 Materials . 6
6 Design and finish . 6
7 Requirements for tracheostomy tubes supplied sterile . 7
8 Marking and labelling . 8
Annexes
A Test method for the security of attachment of connector and neck-plate to tracheostomy tube. 10
A.1 Principle . 10
A.2 Apparatus . 10
A.3 Procedure . 10
A.4 Expression of results . 10
B Test method for determining the resting diameter of the cuff. 11
B.1 Principle . 11
B.2 Apparatus . 11
B.3 Procedure . 11
B.4 Expression of results . 11
C Guidance on materials and design . 12
C.1 Materials . 12
C.2 Design . 12
Bibliography. 13
©
ISO 2000 – All rights reserved iii
---------------------- Page: 9 ----------------------
ISO 5366-1:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical com-
mittees. Each member body interested in a subject for which a technical committee has been established has the
right to be represented on that committee. International organizations, governmental and non-governmental, in liai-
son with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 5366 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 5366-1 was prepared by Technical Committee ISO/TC 121, Anaesthetic and respiratory
equipment, Subcommittee SC 2, Tracheal tubes and other equipment.
This fourth edition cancels and replaces the third edition of ISO 5366-1 and the second edition of ISO 5366-2
(ISO 5366-1:1994 and ISO 5366-2:1993), which have been technically revised.
ISO 5366 consists of the following parts, under the general title Anaesthetic and respiratory equipment — Tracheos-
tomy tubes:
— Part 1: Tubes and connectors for use in adults
— Part 3: Paediatric tracheostomy tubes
Annexes A and B form a normative part of this part of ISO 5366. Annex C is for information only.
©
iv ISO 2000 – All rights reserved
---------------------- Page: 10 ----------------------
ISO 5366-1:2000(E)
Introduction
ISO 5366-1 is one of a series of International Standards dealing with anaesthetic equipment, and is concerned with
the basic requirements and method of size designation of tracheostomy tubes made of plastics materials and/or rub-
ber. Specialized tubes, for example those without a connector at the machine end intended for spontaneously breath-
ing patients, and those with reinforced walls or tubes made of metal are excluded from the scope of this part of
ISO 5366.
This part of ISO 5366 specifies requirements for tracheostomy tubes with an inside diameter of 6,5 mm or greater.
ISO 5366-3 specifies requirements for tracheostomy tubes with an inside diameter from 2,0 to 6,0 mm for paediatric
use.
The method of describing tube dimensions and configuration has been devised in order to assist the clinician in the
selection of a suitable tube to conform as far as possible to a particular patient's anatomy. Size is designated by in-
side diameter, which is important because of its relation to resistance to gas flow. Because the stomal and tracheal
diameters are important when selecting tubes, it is considered essential that the outside diameter be stated for each
size of tube.
Cuffed tracheostomy tubes can be characterized by a combination of the tube inside and outside diameters and by
the cuff resting diameter.
The relationship of cuff and tracheal diameters dictates the intra-cuff pressures required to provide a seal. Excessive
pressure on the tracheal wall can obstruct capillary blood flow.
A range of cuff designs is available to meet the particular clinical requirements. This part of ISO 5366 requires that
the resting diameter of the cuff is marked on the unit package, as this information allows the clinician to match the
product to the application.
A 15 mm male conical connector in accordance with ISO 5356-1 should be used for tracheostomy tubes, as for tra-
cheal tubes, to ensure compatibility with the breathing system of an anaesthetic machine or ventilator.
The tracheostomy tube connector should be permanently attached to the tracheostomy tube to prevent inadvertent
disconnection of the connector from the tube.
Flammability of tracheostomy tubes, for example if flammable anaesthetics, electrosurgical units, or lasers are used
1)
in oxidant-enriched atmospheres, is a well-recognized hazard that is addressed by appropriate clinical manage-
ment, and is outside the scope of this part of ISO 5366.
1) See ISO/TR 11991.
©
ISO 2000 – All rights reserved v
---------------------- Page: 11 ----------------------
INTERNATIONAL STANDARD ISO 5366-1:2000(E)
Anaesthetic and respiratory equipment — Tracheostomy tubes —
Part 1:
Tubes and connectors for use in adults
1 Scope
This part of ISO 5366 specifies requirements for tracheostomy tubes made of plastics materials and/or rubber having
inside diameters of 6,5 mm or greater. Such tubes are primarily designed for patients who require anaesthesia, arti-
ficial ventilation or other respiratory support, but need not be restricted to these uses.
This part of ISO 5366 is not applicable to specialized tubes, and does not address flammability of tracheostomy
tubes.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 5366. For dated references, subsequent amendments to, or revisions of, any of these publications do
not apply. However, parties to agreements based on this part of ISO 5366 are encouraged to investigate the possi-
bility of applying the most recent editions of the normative documents indicated below. For undated references, the
latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently
valid International Standards.
ISO 594-1, Conical fittings with a 6 % (Luer) taper for syringes, needles and certain other medical equipment —
Part 1: General requirements.
ISO 4135, Anaesthetic and respiratory equipment — Vocabulary.
ISO 5356-1, Anaesthetic and respiratory equipment — Conical connectors — Part 1: Cones and sockets.
ISO 5361, Anaesthetic and respiratory equipment — Tracheal tubes and connectors.
ISO 10993-1, Biological evaluation of medical devices — Part 1: Evaluation an
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.