oSIST prEN 15303-1:2007
Design and application of plasterboard systems on frames - Part 1: General
Design and application of plasterboard systems on frames - Part 1: General
This part of this European Standard provides recommendations for the design and application of gypsum plasterboard to meet the performance requirements of the completed works. The products described are covered by harmonised technical specifications.
Recommendations on the installation of plasterboard as drylining and for the construction of plasterboard partitions and ceilings are given in parts 2 to 10 of this standard.
Planung und Ausführung von Gipsplattensystemen auf Unterkonstruktionen - Teil 1: Allgemeines
Dieser Teildieser Europäischen Norm enthält Empfehlungen zur Planung und Anwendung von Gipsplatten mit dem Ziel der Erfüllung der Funktionsanforderungen an die fertigen Bauteile. Die beschriebenen Produkte werden von harmonisierten technischen Spezifikationen abgedeckt.
In den Teilen 2 bis 10 dieser Norm werden Empfehlungen zum Einbau von Gipsplatten als Trockenputz und zur Ausführung von Trennwänden und Decken aus Gipsplatten gegeben.
Conception et mise en oeuvre d'ouvrages en plaques de plâtre sur ossatures - Partie 1: Généralités
Cette partie de la présente Norme européenne donne des recommandations pour la conception et l'application des plaques de plâtre permettant de satisfaire aux exigences des ouvrages terminés. Les produits décrits sont couverts par des spécifications techniques harmonisées.
Des recommandations sur l'installation de plaques de plâtre comme revêtement et sur la construction de cloisons et de plafonds en plaques de plâtre sont données dans les parties 2 à 10 de la présente norme.
Projektiranje in uporaba mavčnih plošč na okvirjih - 1. del: Splošno
General Information
Standards Content (Sample)
SLOVENSKI oSIST prEN 15303-1:2005
PREDSTANDARD
oct 2005
Projektiranje in uporaba mavčnih plošč na okvirjih – 1. del: Splošno
Design and application of plasterboard systems on frames - Part 1: General
ICS 91.100.10 Referenčna številka
oSIST prEN 15303-1:2005(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD
DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2005
ICS
English version
Design and application of plasterboard systems on frames - Part
1: General
Conception et mise en oeuvre d'ouvrages en plaques de Plannung und ausfùhrung von Gipsplatten systemen auf
platre sur ossatures - Partie 1: Generalities unterconstruction - Teil 1 : General
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 241.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15303-1:2005: E
worldwide for CEN national Members.
Contents Page
Foreword. 3
Introduction . 4
1 Scope. 5
2 Normative references . 5
3 Definitions. 5
4 Design . 6
5 Site works . 12
Foreword
This document has been prepared by the Technical Committee CEN/TC 241 “Gypsum and gypsum
based products” the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This standard is one of a series of standards for construction products based on gypsum and their
intended uses.
This standard includes the following parts:
Part 1: General
Part 2: Non-load bearing metal frame partitions
Part 3: Non-load bearing timber frame partitions
Part 4: Load bearing metal frame partitions
Part 5: Load bearing timber frame partitions
Part 6: Metal frame dry linings
Part 7: Timber frame dry linings
Part 8: Metal frame ceilings
Part 9: Timber frame ceilings
Part 10: Non loadbearing shaftwall systems
Introduction
The properties of gypsum plasterboards make them particularly suitable for use in situations
where fire protection, sound and thermal insulation are required. To obtain full advantage of
these properties in partitions, their design and installation have to be correct.
Following the recommendations for the design and installation given in this part of the standard
will enable expected performances to be achieved for non load bearing metal frame partitions.
1 Scope
This part of this European Standard provides recommendations for the design and application
of gypsum plasterboard to meet the performance requirements of the completed works. The
products described are covered by harmonised technical specifications.
Recommendations on the installation of plasterboard as drylining and for the construction of
plasterboard partitions and ceilings are given in parts 2 to 10 of this standard.
2 Normative references
The following referenced documents are indispensable for the application of this document. For
dated references, only the edition cited applies. For undated references, the latest edition of the
referenced document (including any amendments) applies.
prEN 520, Specification for gypsum plasterboards
Part 1: General
EN 13963, Specification for Jointing materials for gypsum plasterboard
EN 14195, Metal framing components — Definitions, requirements and test methods
prEN 14566, Mechanical fasteners for gypsum plasterboard
3 Definitions
For the purposes of this European Standard, the definitions in part 1 and the following
definitions apply:
(Note: these definitions to be copied from EN520 to ensure consistency)
3.1
lining
dry covering to any internal building surface
3.2
plasterboard drylining
lining constructed of gypsum plasterboard
3.3
plasterboard seamless drylining
plasterboard drylining that incorporates plasterboard seamless joints
3.4
gypsum baseboard
gypsum plasterboard in which the gypsum plasterboard face is suitable for receiving gypsum
plaster
3.5
gypsum wallboard
gypsum plasterboard in which the gypsum plasterboard face is suitable for receiving gypsum
plaster
3.6
gypsum wallboard F
gypsum wallboard with a gypsum plasterboard core that maintains its cohesion at high
temperatures
3.7
gypsum plank
gypsum wallboard or gypsum baseboard of narrow width and large thickness
3.8
gypsum moisture resistant wallboard
gypsum wallboard in which the gypsum plasterboard core and paper sheets are water resistant
3.9
gypsum moisture resistant wallboard F
gypsum moisture resistant wallboard with a gypsum plasterboard core that maintains its
cohesion at high temperatures
(Other definitions from EN 520)
3.10
gypsum coreboard
gypsum plasterboard specifically for use between the studs in a shaftwall system
3.11
gypsum Cove
see definition in cove standard
3.12
gypsum plasterboard composite
laminate in which one or more of the layers is gypsum plasterboard
3.13
insulating gypsum plasterboard
gypsum plasterboard composite that incorporates a film of low thermal emissivity
3.14
vapour control gypsum plasterboard
gypsum plasterboard composite that incorporates a film of low water vapour permeability
4 Design
4.1 General
Prior to the commencement of the contract there should be an exchange of pertinent
information between all parties concerned. The designer should include working drawings and
specifications, prepared in sufficient detail to afford proper guidance in the preparation of
estimates and the execution of the work.
When selecting and designing drylining systems the designer should take into account the
following points:
a) The nature and condition of the building elements to which the system will be attached,
including any necessary pre-treatment.
b) The functional requirements.
c) The type of finish / appearance.
d) The dimensions required including:
i) the finished widths, heights and thicknesses of the systems;
ii) details of the nature of junctions with other building elements and construction
details (e.g., doors, windows, ceiling junctions, etc.);
iii) the positioning of installations and fittings;
iv) any other situations that will affect the choice and design of drylining systems.
e) The preparation of other building elements to provide adequate fixing points for drylining
systems as necessary.
f) The work of other trades, particularly concerning services (e.g., pipes, wires, etc.) that are
intended to connect with or run within the drylining system.
g) Manufacturing and building tolerances that may affect the design of the drylining system or
the elements to which it is joined.
National regulations state certain requirements of drylinings that have to be met.
The performance of a drylining system is determined by calculation or testing in accordan
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.