iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 61340-2-3:2001

(Main)

Electrostatics -- Part 2-3: Methods of test for determining the resistance and resistivity of solid planar materials used to avoid electrostatic charge accumulation

Electrostatics -- Part 2-3: Methods of test for determining the resistance and resistivity of solid planar materials used to avoid electrostatic charge accumulation

Describes test methods for the determination of the electrical resistance and resistivity of solid materials in the range from 10K Ohm to 1T Ohm used to avoid electrostatic charge accumulation. It takes account of existing IEC/ISO standards and other published information, and gives recommendations and guidelines on the appropriate method.

Elektrostatik -- Teil 2-3: Prüfverfahren zur Bestimmung des Widerstandes und des spezifischen Widerstandes von festen planen Werkstoffen, die zur Vermeidung elektrostatischer Aufladung verwendet werden

Electrostatique -- Partie 2-3: Méthodes d'essais pour la détermination de la résistance et de la résistivité des matériaux planaires solides destinés à éviter les charges électrostatiques

Décrit les méthodes d'essai pour la détermination de la résistance électrique et de la résistivité des matériaux solides dans la gamme comprise entre 10K Ohm et 1T Ohm destinés à éviter les charges électrostatiques. Elle prend en compte les normes CEI/ISO existantes et autres publications applicables. Elle fournit aussi des recommandations et des lignes directrices sur la méthode appropriée.

Electrostatics - Part 2-3: Methods of test for determining the resistance and resistivity of solid planar materials used to avoid electrostatic charge accumulation

General Information

Status
Withdrawn
Publication Date
31-Aug-2001
Withdrawal Date
10-Oct-2019
ICS
17.220.99 - Other standards related to electricity and magnetism
Technical Committee
I09 - Imaginarni 09
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
11-Oct-2019
Due Date
03-Nov-2019
Completion Date
11-Oct-2019
Ref Project
EN 61340-2-3:2000 - Electrostatics - Part 2-3: Methods of test for determining the resistance and resistivity of solid planar materials used to avoid electrostatic charge accumulation

Relations

Replaced By
SIST EN 61340-2-3:2016 - Electrostatics - Part 2-3: Methods of test for determining the resistance and resistivity of solid materials used to avoid electrostatic charge accumulation (IEC 61340-2-3:2016)
Effective Date
18-Oct-2016
Revised
SIST EN 61340-2-3:2016 - Electrostatics - Part 2-3: Methods of test for determining the resistance and resistivity of solid materials used to avoid electrostatic charge accumulation (IEC 61340-2-3:2016)
Effective Date
14-Apr-2015

Buy Standard

EN 61340-2-3:2001EN 61340-2-3:2001
PreviousNext
Standard
EN 61340-2-3:2001
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61340-2-3:2001
01-september-2001
Electrostatics - Part 2-3: Methods of test for determining the resistance and
resistivity of solid planar materials used to avoid electrostatic charge
accumulation
Electrostatics -- Part 2-3: Methods of test for determining the resistance and resistivity of
solid planar materials used to avoid electrostatic charge accumulation
Elektrostatik -- Teil 2-3: Prüfverfahren zur Bestimmung des Widerstandes und des
spezifischen Widerstandes von festen planen Werkstoffen, die zur Vermeidung
elektrostatischer Aufladung verwendet werden
Electrostatique -- Partie 2-3: Méthodes d'essais pour la détermination de la résistance et
de la résistivité des matériaux planaires solides destinés à éviter les charges
électrostatiques
Ta slovenski standard je istoveten z: EN 61340-2-3:2000
ICS:
17.220.99 Drugi standardi v zvezi z Other standards related to
elektriko in magnetizmom electricity and magnetism
SIST EN 61340-2-3:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61340-2-3:2001

---------------------- Page: 2 ----------------------

SIST EN 61340-2-3:2001

---------------------- Page: 3 ----------------------

SIST EN 61340-2-3:2001

---------------------- Page: 4 ----------------------

SIST EN 61340-2-3:2001

---------------------- Page: 5 ----------------------

SIST EN 61340-2-3:2001

---------------------- Page: 6 ----------------------

SIST EN 61340-2-3:2001

---------------------- Page: 7 ----------------------

SIST EN 613
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 61340-2-1:2016/A1:2022(Amendment)
Electrostatics - Part 2-1: Measurement methods - Ability of materials and products to dissipate static electric charge (IEC 61340-2-1:2015/AMD1:2022)
EN 61340-2-1:2015/A1:2022

This part of IEC 61340 describes test methods for measuring the rate of dissipation of static charge of insulating and static materials and products.
It includes a generic description of test methods and detailed test procedures for specific applications.
The two test methods for measuring charge decay time, one using corona charging and one using a charged metal plate are different and might not give equivalent results. Nevertheless, each method has a range of applications for which it is best suited. The corona charging method is suitable for evaluating the ability of materials, for example textiles, packaging, etc., to dissipate charge from their own surfaces. The charged metal plate method is suitable for evaluating the ability of materials and objects such as gloves, finger cots, hand tools, etc. to dissipate charge from conductive objects placed on or in contact with them. The charged plate method might not be suitable for evaluating the ability of materials to dissipate charge from their own surfaces.
In addition to its general application, this horizontal standard is also intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 108.
One of the responsibilities of a technical committee is, wherever applicable, to make use of horizontal standards in the preparation of its publications. The contents of this horizontal standard shall not apply unless specifically referred to or included in the relevant publications.

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61340-5-3:2022(Main)
Electrostatics - Part 5-3: Protection of electronic devices from electrostatic phenomena - Properties and requirements classification for packaging intended for electrostatic discharge sensitive devices (IEC 61340-5-3:2022)
EN IEC 61340-5-3:2022

This part of IEC 61340 defines the ESD protective packaging properties needed to protect ESD sensitive devices (ESDS) through all phases of production, rework/maintenance, transport and storage. Test methods are referenced to evaluate packaging and packaging materials for these product and material properties. Performance limits are provided.
This standard does not address protection from electromagnetic interference (EMI), electromagnetic pulsing (EMP) or protection of electrically initiated explosive materials or devices.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61340-6-1:2019(Main)
Electrostatics - Part 6-1: Electrostatic control for healthcare - General requirements for facilities (IEC 61340-6-1:2018)
EN IEC 61340-6-1:2018

This part of IEC 61340 applies to facilities that provide healthcare including hospitals, care
centres and clinics.
This document provides technical requirements and recommendations for controlling
electrostatic phenomena in healthcare facilities, which includes requirements for equipment,
materials, and products used to control static electricity.
The requirements of this document do not apply to medical electrical equipment specified in
IEC 60601-1 [1] 1 and in vitro diagnostic (IVD) medical equipment specified in
IEC 61010-2-101 [2].

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61340-4-4:2018(Main)
Electrostatics - Part 4-4: Standard test methods for specific applications - Electrostatic classification of flexible intermediate bulk containers (FIBC) (IEC 61340-4-4:2018)
EN IEC 61340-4-4:2018

This part of IEC 61340 specifies requirements for flexible intermediate bulk containers (FIBC)
between 0,25 m3 and 3 m3 in volume, intended for use in hazardous explosive atmospheres.
The explosive atmosphere can be created by the contents in the FIBC or can exist outside the
FIBC.
The requirements include:
– classification and labelling of FIBC;
– classification of inner liners;
– specification of test methods for each type of FIBC, inner liner, labels and document
pockets;
– design and performance requirements for FIBC, inner liners, labels and document pockets;
– safe use of FIBC (including those with inner liners) within different zones defined for
explosion endangered environments, described for areas where combustible dusts are, or
can be, present (IEC 60079-10-2), and for explosive gas atmospheres (IEC 60079-10-1);
– procedures for type qualification and certification of FIBC, including the safe use of inner
liners.
NOTE 1 Guidance on test methods that can be used for manufacturing quality control is given in Annex C.
The requirements of this document are applicable to all types of FIBC and inner liners, tested
as manufactured, prior to use and intended for use in hazardous explosive atmospheres:
Zones 1 and 2 (Groups IIA and IIB only) and Zones 21 and 22 (see Annex D for classification
of hazardous areas and explosion groups). For some types of FIBC, the requirements of this
document apply only to use in hazardous explosive atmospheres with minimum ignition
energy of 0,14 mJ or greater and where charging currents do not exceed 3,0 μA.
NOTE 2
0,14 mJ represents a realistic minimum ignition energy for a Group IIB gas or vapour atmosphere. Although more
sensitive materials exist, 0,14 mJ is the lowest minimum ignition energy of any material that is likely to be present
when FIBC are emptied. 3,0 μA is the highest charging current likely to be found in common industrial processes.
This combination of minimum ignition energy and charging current represents the most severe conditions that
might be expected in practice.
FIBC are not normally used in Zone 0 or Zone 20. If FIBC are used in Zone 0 or Zone 20, the
requirements of this document are applicable, together with additional requirements that are
beyond the scope of this document to define.
The volume contained within FIBC can be designated as Zone 20, in which case the
requirements of this document are applicable.
Solids containing residual solvent can result in a hazardous explosive atmosphere within
FIBC, possibly resulting in the volume being designated as Zone 1 or Zone 2; in which case
the requirements of this document are applicable.
Compliance with the requirements specified in this document does not necessarily ensure that
hazardous electrostatic discharges, for example cone discharges, will not be generated by the
contents in FIBC. Information on the risks associated with cone discharges is given in
Annex E.
Compliance with the requirements of this document does not mitigate the need for full risk
assessment. For example, metal and other conductive powders and toner powders can
require additional precautions to prevent hazardous discharges from the powders.
NOTE 3 In the examples mentioned in the paragraph above, additional precautions can be necessary in the case
of metal or other conductive powder because if the powder is isolated and becomes charged, incendiary sparks can
occur, and in the case of toner powders, incendiary discharges can occur during rapid filling and emptying
operations. IEC TS 60079-32-1 [1]1 gives guidance on additional precautions that can be necessary.
Test methods included in this document can be used in association with other performance
requirements, for example when a risk assessment has shown the minimum ignition energy of
concern is less than 0,14 mJ, charging currents are greater than 3,0 μA, or the ambient
conditions are outside of the range specified in this document.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61340-4-5:2018(Main)
Electrostatics - Part 4-5: Standard test methods for specific applications - Methods for characterizing the electrostatic protection of footwear and flooring in combination with a person (IEC 61340-4-5:2018)
EN IEC 61340-4-5:2018

This part of IEC 61340 specifies test methods for evaluating electrostatic protection provided
by a system of footwear and flooring in combination with a person.
Test results are valid only for the specific footwear and flooring combination tested.
The test methods are not intended for individual product qualification purposes.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61340-4-3:2018(Main)
Electrostatics - Part 4-3: Standard test methods for specific applications - Footwear (IEC 61340-4-3:2017)
EN IEC 61340-4-3:2018

This part of IEC 61340 describes a test method for determining the electrical resistance of
footwear (shoes, slippers or booties) used in the control of electrostatic potential on people.
This document is suitable for use by the manufacturer of footwear as well as the end user. A
method for measuring the electrical resistance of footwear alone is described and serves as a
qualification test or an acceptance test for new footwear, or as a periodic test of in-use
footwear.
Although this document does not include requirements for personal safety, footwear used
within the scope of this document in all places of work is regulated by the relevant local
statutory requirements regarding the health and safety of all persons.
Insulating footwear is not included within the scope of this document although the electrical
resistance measurement techniques can be applicable.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61340-5-1:2017/AC:2017(Corrigendum)
Electrostatics - Part 5-1: Protection of electronic devices from electrostatic phenomena - General requirements (IEC 61340-5-1:2016/COR1:2017)
EN 61340-5-1:2016/AC:2017-05
  • Corrigendum
    3 pages
    French language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61340-4-7:2017(Main)
Electrostatics - Part 4-7: Standard test methods for specific applications - Ionization (IEC 61340-4-7:2017)
EN 61340-4-7:2017

This part of IEC 61340 provides test methods and procedures for evaluating and selecting air
ionization equipment and systems (ionizers).
This document establishes measurement techniques, under specified conditions, to determine
offset voltage (ion balance) and decay (charge neutralization) time for ionizers.
This document does not include measurements of electromagnetic interference (EMI), or the
use of ionizers in connection with ordnance, flammables, explosive items or electrically
initiated explosive devices.
As contained in this document, the test methods and test conditions can be used by
manufacturers of ionizers to provide performance data describing their products. Users of
ionizers are urged to modify the test methods and test conditions for their specific application
in order to qualify ionizers for use, or to make periodic verifications of ionizer performance.
The user will decide the extent of the data required for each application.
CAUTION: Procedures and equipment described in this document can expose personnel to hazardous electrical
and non-electrical conditions. Users of this document are responsible for selecting equipment that complies with
applicable laws, regulatory codes and both external and internal policy. Users are cautioned that this document
cannot replace or supersede any requirements for personnel safety.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61340-5-1:2017(Main)
Electrostatics - Part 5-1: Protection of electronic devices from electrostatic phenomena - General requirements (IEC 61340-5-1:2016)
EN 61340-5-1:2016

Applies to activities that: manufacture, process, assemble, install, package, label, service, test, inspect, transport or otherwise handle electrical or electronic parts, assemblies and equipment susceptible to damage by electrostatic discharges greater than or equal to 100 V human body model (HBM).   Provides the requirements for an ESD control program.  The user should refer to IEC 61340-5-2 for guidance on the implementation of this standard. Does not apply to electrically initiated explosive devices, flammable liquids, gases and powders. The purpose of this standard is to provide the administrative and technical requirements for establishing, implementing and maintaining an ESD control program (hereinafter referred to as the 'program'). The main changes with respect to the previous edition are listed below: This version of IEC 61340-5-1 focuses on the requirements for an ESD control program. In addition, this version of IEC 61340-5-1 has been aligned with other major ESD control program standards used throughout the world.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61340-2-3:2016(Main)
Electrostatics - Part 2-3: Methods of test for determining the resistance and resistivity of solid materials used to avoid electrostatic charge accumulation (IEC 61340-2-3:2016)
EN 61340-2-3:2016

Describes test methods for the determination of the electrical resistance and resistivity of solid materials in the range from 10K Ohm to 1T Ohm used to avoid electrostatic charge accumulation. It takes account of existing IEC/ISO standards and other published information, and gives recommendations and guidelines on the appropriate method.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day