iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST ENV 1927-1:2003

(Main)

Qualitative classification of softwood round timber - Part 1: Spruces and firs

Qualitative classification of softwood round timber - Part 1: Spruces and firs

This standard specifies the qualitative classification for the roundwood of spruces (Picea spp) and firs (Abies spp). The classification is made either using clauses 4 and 5 or using clause 6. Clauses 4 and 5 describe the qualitative classification of round timber for which the intended use is unknown. Clause 6 gives the characteristics to be included in all national standards describing a qualitative classification or as guideline for contracts describing qualities for round timber of spruces and firs where the intended use is known.

Qualitäts-Sortierung von Nadel-Rundholz - Teil 1: Fichten und Tannen

Diese Norm legt die Qualitäts-Sortierung von Fichten- und Tannen-Rundholz fest (Picea spp und Abies spp). Die Sortierung kann entweder nach den Abschnitten 4 und 5 oder nach dem Abschnitt 6 vorgenommen werden. Die Abschnitte 4 und 5 beschreiben die verwendungsneutrale Qualitäts-Sortierung. Der Abschnitt 6 beschreibt die Kriterien, welche bei allen nationalen Normen für verwendungsbezogenes Nadel-Rundholz (Fichten- und Tannen) aufgenommen werden. Bei Verträgen über verwendungsbezogenes Rundholz werden die in Abschnitt 6 aufgeführten Merkmale angewendet.

Classement qualitatif des bois ronds résineux - Partie 1: Epicéas et sapins

La présente norme spécifie le classement qualitatif des bois ronds d'épicéas (Picea spp) et de sapins (Abies spp). Le classement est réalisé soit en utilisant les articles 4 et 5, soit l'article 6. Les articles 4 et 5 décrivent le classement qualitatif de bois ronds dont la destination n'est pas connue. L'article 6 donne les caractéristiques devant etre incluses dans toutes normes nationales décrivant un classement qualitatif ou servir de guide a des contrats fixant les qualités des bois ronds d'épicéas et de sapins, dont la destination est connue.

Razvrščanje okroglega lesa iglavcev po kakovosti – 1. del: Smreke in jelke

General Information

Status
Withdrawn
Publication Date
31-May-2003
Withdrawal Date
28-Apr-2008
ICS
79.040 - Wood, sawlogs and sawn timber
Technical Committee
LES - Round and sawn timber
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
28-Mar-2008
Due Date
20-Apr-2008
Completion Date
29-Apr-2008
Ref Project
ENV 1927-1:1998 - Qualitative classification of softwood round timber - Part 1: Spruces and firs

Relations

Replaced By
SIST EN 1927-1:2008 - Qualitative classification of softwood round timber - Part 1: Spruces and firs
Effective Date
01-Jul-2008

Buy Standard

ENV 1927-1:2003ENV 1927-1:2003
PreviousNext
Standardization document
ENV 1927-1:2003
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ENV 1927-1:2003
01-junij-2003
5D]YUãþDQMHRNURJOHJDOHVDLJODYFHYSRNDNRYRVWL±GHO6PUHNHLQMHONH
Qualitative classification of softwood round timber - Part 1: Spruces and firs
Qualitäts-Sortierung von Nadel-Rundholz - Teil 1: Fichten und Tannen
Classement qualitatif des bois ronds résineux - Partie 1
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1927-2:2008/AC:2010(Corrigendum)
Qualitative classification of softwood round timber - Part 2: Pines
EN 1927-2:2008/AC:2009

TC - Modification to Table 1.

  • Corrigendum
    2 pages
    German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 975-1:2009(Main)
Sawn timber - Appearance grading of hardwoods - Part 1: Oak and beech
EN 975-1:2009

This European Standard specifies the rules determining the quality of appearance graded sawn timber. It describes various grades of temperate hardwood rough sawn timber and regularized timber for which it lays down denominations and definitions. It also gives rules for composition and acceptance of batches. This standard gives minimum requirements for each grade classification. Sawn timber not included within limits given in this standard may be defined, if necessary, by contract specifications established on the basis of this standard. This standard applies to grading of green and dried timber. Characteristics apply at the time of grading. This standard does not apply to the strength grading of structural timber or to sawn timber for pallets. This standard is applicable to the following products: a) Oak sawn timber, in the following categories: 1) Un-edged boards: individual selected pieces and boules; 2) Square edged timber and strips (not exceeding 41 mm thickness); 3) Baulks (sum of thickness + width ≥ 200 mm and thickness ≥ 80 mm). b) Beech sawn timber, in the following categories: 1) Un-edged boards: individual selected pieces and boules; 2) Square edged timber and strips; 3) Prepared timber (dried timber).

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 942:2008(Main)
Timber in joinery - General requirements
EN 942:2007

This European Standard specifies the general requirements including in particular the grading and classification by appearance quality of timber in joinery products or individual joinery parts.
This European Standard is intended to be used at the time of manufacture of a product.  However this Standard may be used to evaluate products at a later stage, but in these situations storage and service conditions, subsequent to manufacture, shall be taken into account (surface checks).
Where European product standards exist their timber requirements shall take precedence, unless an alternative improved specification is given as identified in Annex D.  If reference to this European Standard is made the specific grade and requirements shall be identified.
This European Standard covers solid, finger-jointed, end-jointed, edge-jointed and laminated timber products.
Matters relating to the influence of timber characteristics on strength and durability are not covered in this Standard.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1927-1:2008(Main)
Qualitative classification of softwood round timber - Part 1: Spruces and firs
EN 1927-1:2008

This European Standard specifies the qualitative classification for the roundwood of spruces (Picea spp) and firs (Abies spp). The classification is made either using Clauses 4 and 5 or using Annex A. Clauses 4 and 5 describe the qualitative classification of round timber for which the intended use is unknown.
Informative Annex A gives a list of characteristics which serves as a guideline for contracts describing qualities for round timber of spruces and firs where the intended use is known.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1927-2:2008(Main)
Qualitative classification of softwood round timber - Part 2: Pines
EN 1927-2:2008

This European Standard specifies the qualitative classification for the roundwood of pines. It applies to Scots pine (Pinus sylvestris), Corsican or Austrian pine (Pinus nigra), maritime pine (Pinus pinaster) and radiata pine (Pinus radiata). The classification is made either using Clauses 4 and 5 or using Annex A. Clauses 4 and 5 describe the qualitative classification of round timber for which the intended use is unknown.
Informative Annex A gives a list of characteristics which serves as a guideline for contracts describing qualities for round timber of pines where the intended use is known.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 12169:2008
Criteria for the assessment of conformity of a lot of sawn timber
CEN/TS 12169:2008

This Standard defines the sampling plans and procedures for inspection by attributes of sawn timber lots exhibiting a homogenous distribution of properties.It also gives control regulations and conditions for conformity or non conformity of a lot in view of the agreed specification. This document applies to any sawn timber products claimed to comply with specifications defined in the sales contract. It does not cover the spread of different qualities within a grade or between the contracted grades. In case of a dispute, a sampling carried out only by customer or supplier is not valid as it cannot be guaranteed to be free from manipulation. Furthermore parties are free to enlarge the sampling or make use of another method provided an agreement is made between the interested parties.

  • Technical specification
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1927-3:2008(Main)
Qualitative classification of softwood round timber - Part 3: Larches and Douglas fir
EN 1927-3:2008

This Standard specifies the qualitative classification for the roundwood of larches (Larix) and Douglas fir (Pseudotsuga). The classification is made either using Clauses 4 and 5 or using informative Annex A. Clauses 4 and 5 describe the qualitative classification of round timber for which the intended use is unknown.
Annex A gives a list of characteristics which serves as guideline for contracts describing qualities for round timber of larches and Douglas fir where the intended use is known.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 15679:2008(Main)
Thermal Modified Timber - Definitions and characteristics
CEN/TS 15679:2007

This Technical Specification gives definitions and characteristics for Thermally Modified Timber. TMT is used in interior (dry, humid) and exterior conditions.
NOTE 1   TMT is usually a semi-finished product ;  applications are e.g. flooring, panelling, cladding, decking, windows, doors,  furniture and other internal and external joinery. Their product standards give requirements and  test methods which are to be taken into consideration.
NOTE 2   Usage in load bearing applications - reference to relevant EN standards should be made.

  • Technical specification
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1309-2:2006(Main)
Round and sawn timber - Method of measurement of dimensions - Part 2: Round timber - Requirements for measurement and volume calculation rules
EN 1309-2:2006

This European Standard defines the principles which are to be used in the derivation of round timber measurement and volume calculation rules. This standard applies to rules for measuring hardwood and softwood felled round timber. It does not apply to tropical timber.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 975-2:2005(Main)
Sawn timber - Appearance grading of hardwoods - Part 2: Poplars
EN 975-2:2004

This standard defines appearance grades for European poplars
The standard applies to dry and green sawn timber , of thickness 18mm up to 34 mm and of width 100mm up to 250mm measured in a green state..
This standard does not apply to the strength grading of structural timber.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day