SIST EN 2256:2005

Aerospace series - Aluminium alloy AL-P2618A - T852 - Hand and die forgings - a </= 150 mm

This standard specifies the requirements relating to:
Aluminium alloy AL-P2618A
T852
Hand and die forgings
a < 150 mm
for aerospace application.

Luft- und Raumfahrt - Aluminiumlegierung AL-P2618A - T852 - Freiform- und Gesenkschmiedestücke - a </= 150 mm

Diese Norm legt die Anforderungen an
Aluminiumlegierung AL P2618A
T852
Freiform- und Gesenkschmiedestücke
a < or = 150 mm
für Anwendungen in der Luft- und Raumfahrt fest.

Série aérospatiale - Alliage d'aluminium AL-P2618A - T852 - Pieces forgées et matricées - a </= 150 mm

Aeronavtika - Aluminijeva zlitina AL-P2618A - T852 - Prosto in utopno kovani izkovki - a </= 150 mm

General Information

• Status: Published
• Publication Date: 31-Mar-2005
• ICS: 49.025.20 - Aluminium
• Technical Committee: SS SPL - Technical Board for the general field
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Apr-2005
• Due Date: 01-Apr-2005
• Completion Date: 01-Apr-2005
• Ref Project: EN 2256:2004 - Aerospace series - Aluminium alloy AL-P2618A - T852 - Hand and die forgings - a </= 150 mm

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2005
Aeronavtika - Aluminijeva zlitina AL-P2618A - T852 - Prosto in utopno kovani
izkovki - a Aerospace series - Aluminium alloy AL-P2618A - T852 - Hand and die forgings - a 150 mm
Luft- und Raumfahrt - Aluminiumlegierung AL-P2618A - T852 - Freiform- und
Gesenkschmiedestücke - a Série aérospatiale - Alliage d'aluminium AL-P2618A - T852 - Pieces forgées et matricées
- a Ta slovenski standard je istoveten z: EN 2256:2004
ICS:
49.025.20 Aluminij Aluminium
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 2256
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2004
ICS 49.025.20
English version
Aerospace series - Aluminium alloy AL-P2618A - T852 - Hand
and die forgings - a ≤ 150 mm
Série aérospatiale - Alliage d'aluminium AL-P2618A - T852 Luft- und Raumfahrt - Aluminiumlegierung AL-P2618A -
- Pièces forgées et matricées - a ≤ 150 mm T852 - Freiform- und Gesenkschmiedestücke - a ≤ 150 mm
This European Standard was approved by CEN on 15 July 2004.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2256:2004: E
worldwide for CEN national Members.

Contents                                                   Page
Foreword.3
Introduction .4
1 Scope .4
2 Normative references .4

Foreword
This document (EN 2256:2004) has been prepared by the European Association of Aerospace
Manufacturers - Standardization (AECMA-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
AECMA, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2004, and conflicting national standards shall be withdrawn at
the latest by June 2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hu
...