SIST EN 3905:2008

Aerospace series - Six lobe recesses for bolts - Technical specification

This standard specifies the characteristics and qualification requirements for six lobe recesses defined by EN 3911 for bolts. The requirements of this specification are additional to the requirements of the relevant bolt technical specification.

Luft- und Raumfahrt - Sechs-Bogenzahn-Innenantrieb für Schrauben - Technische Lieferbedingungen

Diese Norm legt die Eigenschaften und Qualifikationsanforderungen für den Sechs-Bogenzahn-Innenantrieb nach EN 3911 für Schrauben fest. Die Anforderungen dieser Lieferbedingungen gelten zusätzlich zu den Anforderungen der Technischen Lieferbedingungen für die jeweiligen Schrauben.

Série aérospatiale - Empreinte six lobes pour vis - Spécification technique

Aeronavtika - Šestzoba vdolbina za vijake - Tehnična specifikacija

General Information

• Status: Published
• Publication Date: 25-May-2008
• ICS: 49.030.20 - Bolts, screws, studs
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 09-May-2008
• Due Date: 14-Jul-2008
• Completion Date: 26-May-2008
• Ref Project: EN 3905:2008 - Aerospace series - Six lobe recesses for bolts - Technical specification

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Six lobe recesses for bolts - Technical specificationDSérie aérospatiale - Empreinte six lobes pour vis - Spécification techniqueLuft- und Raumfahrt - Sechs-Bogenzahn-Innenantrieb für Schrauben - Technische Lieferbedingungen49.030.20Sorniki, vijaki, stebelni vijakiBolts, screws, studsICS:SIST EN 3905:2008enTa slovenski standard je istoveten z:EN 3905:200801-julij-2008SIST EN 3905:2008SLOVENSKI
STANDARD







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3905April 2008ICS 49.030.20 English VersionAerospace series - Six lobe recesses for bolts - TechnicalspecificationSérie aérospatiale - Empreinte six lobes pour vis -Spécification techniqueLuft- und Raumfahrt - Sechs-Bogenzahn-Innenantrieb fürSchrauben - Technische LieferbedingungenThis European Standard was approved by CEN on 29 February 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3905:2008: E



EN 3905:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Qualification.4 4 Requirements.4 5 Apparatus.4 5.1 Test block.4 5.2 Nut.4



EN 3905:2008 (E) 3 Foreword This document (EN 3905:2008) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and
...