SIST ISO/IEC 7501-1:2010

Identification cards - Machine readable travel documents - Part 1: Machine readable passport

ISO/IEC 7501-1:2008 is intended for use in all applications relating to machine readable passports. It specifies the form and provides guidance on the construction of machine readable passports (MRPs), in particular in relation to those aspects of the MRP where details of the rightful holder are presented in a form which is both visual and machine readable. It equally defines the specifications to be used by States wishing to issue an electronically enabled version of the MRP (ePassport) for secure carriage and access to an expanded set of details, including globally interoperable biometric data for confirming the presenter as the rightful holder of the ePassport.

Cartes d'identification - Documents de voyage lisibles par machine - Partie 1: Passeport lisible par machine

Identifikacijski dokumenti - Strojno berljivi potni dokumenti - 1. del: Strojno berljiv potni list

ISO/IEC 7501-1:2008 je namenjen za vse uporabe, povezane s strojno berljivimi potnimi listi. Določa obliko in zagotavlja vodila za izdelavo strojno berljivega potnega lista (MRP), še posebej v razmerju do tistih vidikov MRP, kjer so podrobnosti zakonitega lastnika predstavljene v obliki, ki je tako vizualno kot strojno berljiva. Prav tako določa specifikacije, ki jih uporabljajo države za izdajo elektronsko omogočene različice MRP (e-potni list) za varni prenos in dostop do razširjenega niza podrobnosti, vključno z globalnimi interoperabilnimi biometričnimi podatki za potrjevanje predlagatelja kot zakonitega lastnika e-potnega lista.

General Information

• Status: Published
• Public Enquiry End Date: 31-Jul-2010
• Publication Date: 15-Aug-2010
• ICS: 35.240.15 - Identification cards. Chip cards. Biometrics
• Technical Committee: ITC - Information technology
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Aug-2010
• Due Date: 10-Oct-2010
• Completion Date: 16-Aug-2010
• Ref Project: ISO/IEC 7501-1:2008 - Identification cards — Machine readable travel documents — Part 1: Machine readable passport

Relations

• Replaces: SIST ISO/IEC 7501-1:2003 - Identification cards -- Machine readable travel documents -- Part 1: Machine readable passport
• Effective Date: 01-Sep-2010

Standards Content (Sample)

INTERNATIONAL ISO/IEC
STANDARD 7501-1
Fifth edition
2008-09-01

Identification cards — Machine readable
travel documents —
Part 1:
Machine readable passport
Cartes d'identification — Documents de voyage lisibles par machine —
Partie 1: Passeport lisible par machine




Reference number
ISO/IEC 7501-1:2008(E)
©
ISO/IEC 2008

---------------------- Page: 1 ----------------------
ISO/IEC 7501-1:2008(E)

PDF disclaimer
PDF files may contain embedded typefaces. In accordance with Adobe's licensing policy, such files may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading a PDF file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create the PDF file(s) constituting this document can be found in the General Info relative to
the file(s); the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the files are suitable for
use by ISO member bodies. In the unlikely event that a problem relating to them is found, please inform the Central Secretariat at the
address given below.

This CD-ROM contains:
1) the publication ISO/IEC 7501-1:2008 in portable document format (PDF), which can be viewed using
Adobe® Acrobat® Reader;
2) ICAO Doc 9303 Part 1, Volumes 1 and 2 in portable document format (PDF), which can be viewed
using Adobe® Acrobat® Reader.
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.

This fifth edition cancels and replaces the fourth edition (ISO/IEC 7501-1:2005), which has been technically
revised.
COPYRIGHT PROTECTED DOCUMENT


©  ISO/IEC 2008
All rights reserved. Unless required for installation or otherwise specified, no part of this CD-ROM may be reproduced, stored in a retrieval
system or transmitted in any form or by any means without prior permission from ISO. Requests for permission to reprod
...

SLOVENSKI STANDARD
SIST ISO/IEC 7501-1:2010
01-september-2010
1DGRPHãþD
SIST ISO/IEC 7501-1:2003
Identifikacijski dokumenti - Strojno berljivi potni dokumenti - 1. del: Strojno berljiv
potni list
Identification cards - Machine readable travel documents - Part 1: Machine readable
passport
Cartes d'identification - Documents de voyage lisibles par machine - Partie 1: Passeport
lisible par machine
Ta slovenski standard je istoveten z: ISO/IEC 7501-1:2008
ICS:
35.240.15 Identifikacijske kartice in Identification cards and
sorodne naprave related devices
SIST ISO/IEC 7501-1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO/IEC 7501-1:2010

---------------------- Page: 2 ----------------------

SIST ISO/IEC 7501-1:2010

INTERNATIONAL ISO/IEC
STANDARD 7501-1
Fifth edition
2008-09-01


Identification cards — Machine readable
travel documents —
Part 1:
Machine readable passport
Cartes d'identification — Documents de voyage lisibles par machine —
Partie 1: Passeport lisible par machine



Reference number
ISO/IEC 7501-1:2008(E)
©
ISO/IEC 2008

---------------------- Page: 3 ----------------------

SIST ISO/IEC 7501-1:2010
ISO/IEC 7501-1:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO/IEC 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2008 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO/IEC 7501-1:2010
ISO/IEC 7501-1:2008(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 7501-1 was prepared by the International Civil Aviation Organization (as ICAO Doc 9303, Part 1,
sixth edition. 2006) and was adopted, under a special "fast-track procedure", by Joint Technical Committee
ISO/IEC JTC 1, Information technology, in parallel with its approval by the national bodies of ISO and IEC.
This fifth edition cancels and replaces the fourth edition (ISO/IEC 7501-1:2005), which has been technically
revised.
ISO/IEC 7501 consists of the following parts, under the general title Identification cards — Machine readable
travel documents:
⎯ Part 1: Machine readable passport
⎯ Part 2: Machine readable visa
⎯ Part 3: Machine readable official travel documents

© ISO/IEC 2008 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO/IEC 7501-1:2010

---------------------- Page: 6 ----------------------

SIST ISO/IEC 7501-1:2010
INTERNATIONAL STANDARD ISO/IEC 7501-1:2008(E)

Identification cards — Machine readable travel documents —
Part 1:
Machine readable passport
The following document is adopted as ISO/IEC 7501-1:2008:
Sixth Edition of the International Civil Aviation Organization (ICAO) Document, i.e. Doc 9303 Part 1 -
Machine Readable Passports; specifically,
from Volume 1 – Passports with Machine Readable Data Stored in Optical Character Recognition
Format
Section II Technical specifications for machine readable passports – References and definitions;
Section III Technical specifications for the security of the design, manufacture and issuance of
machine readable travel documents; and
Section IV Technical specifications for machine readable passports;
and
from Volume 2 – Specifications for Electronically Enabled Passports with Biometric Identification
Capability
Section II The deployment of biometric identification and the electronic storage of data in machine
readable passports;
Section III A logical data structure for contactless integrated circuit data storage technology; and
Section IV PKI for machine readable travel documents offering ICC read only access.

ISO/IEC 7501-1:2008 is intended for use in all applications relating to machine readable passports. It specifies
the form and provides guidance on the construction of machine readable passports (MRPs), in particular in
relation to those aspects of the MRP where details of the rightful holder are presented in a form which is both
visual and machine readable. It equally defines the specifications to be used by States wishing to issue an
electronically enabled version of the MRP (ePassport) for secure carriage and access to an expanded set of
details, including globally interoperable biometric data for confirming the presenter as the rightful holder of the
ePassport.
ICAO Doc 9303 Part 1 is maintained by a Technical Advisory Group on Machine Readable Travel Documents
(TAG/MRTD). ISO/IEC JTC 1 has provided and continues to provide liaison during the TAG/MRTD meetings
on ICAO Doc 9303 Part 1 and considered the technical specifications to which the endorsement notice
applies.
Information on
...