SIST EN ISO 20558-1:2019

Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 20558-1:2018)

This document establishes a system of designation for poly(phenylene sulfide) (PPS) thermoplastic materials, which can be used as the basis for specifications.
The types of poly(phenylene sulfide) (PPS) materials are differentiated from each other by a classification system based on appropriate levels of the designatory properties
a) melt mass-flow rate or melt viscosity;
b) density;
c) tensile modulus;
and on information about the intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials.
This document is applicable to all PPS materials. It applies to materials ready for normal use in the form of powder, granules or pellets and to materials unmodified or modified by colorants, additives, fillers, etc.
It is not intended to imply that materials having the same designation give necessarily the same performance. This document does not provide engineering data, performance data or data on processing conditions which can be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they are intended to be determined in accordance with the test methods specified in ISO 20558‑2, if suitable.
In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, the requirements are given in data block 5 (see 4.1).

Kunststoffe - Polyphenylensulfid (PPS)-Werkstoffe - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 20558-1:2018)

Plastiques - Matériaux pour moulage et extrusion en poly(phénylène sulfide) (PPS) - Partie 1: Système de désignation et base de spécification (ISO 20558-1:2018)

Le présent document établit un système de désignation des matériaux thermoplastiques à base de poly(sulfure de phénylène) (PPS) qui peut être utilisé comme base pour les spécifications.
Les types de matériaux à base de poly(sulfure de phénylène) (PPS) sont différenciés les uns des autres par un système de classification fondé sur des niveaux appropriés des propriétés de désignation:
a) indice de fluidité à chaud en masse ou viscosité à l'état fondu;
b) masse volumique;
c) module en traction;
et des informations sur l'application prévue et/ou la méthode de mise en œuvre, les propriétés importantes, les additifs, les colorants, les charges et les matériaux de renfort.
Le présent document est applicable à tous les matériaux à base de PPS. Il s'applique aux matériaux prêts à l'emploi dans le cadre d'une utilisation normale sous la forme de poudre, granulés ou grains et aux matériaux non modifiés ou modifiés par des colorants, additifs, charges, etc.
Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les mêmes performances. Le présent document ne comporte pas de données sur la conception, la performance ou les conditions de mise en œuvre qui peuvent être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en œuvre particulière. Si de telles caractéristiques supplémentaires sont nécessaires, elles doivent être déterminées conformément aux méthodes d'essai spécifiées dans l'ISO 20558‑2, s'il y a lieu.
Afin de spécifier un matériau thermoplastique pour une application particulière ou d'assurer une méthode de mise en œuvre reproductible, des exigences sont codées dans le bloc de données 5 (voir 4.1).

Polimerni materiali - Materiali na osnovi polifenilensulfida (PPS) za oblikovanje in ekstrudiranje - 1. del: Sistem označevanja in podlage za specifikacije (ISO 20558-1:2018)

Ta dokument določa sistem označevanja plastomernih materialov na osnovi polifenilensulfida (PPS), ki jih je mogoče uporabiti kot podlago za specifikacije.
Vrste materialov na osnovi polifenilensulfida se med seboj ločujejo glede na sistem razvrščanja, ki temelji na ustreznih ravneh naslednjih označevalnih lastnosti:
a) masni pretok taline ali viskoznost taline;
b) gostota;
c) natezni modul;
ter informacijah o predvideni uporabi in/ali metodi obdelave, pomembnih lastnostih, aditivih, barvilih, polnilih in materialih za ojačanje.
Ta dokument se uporablja za vse vrste materialov PPS. Uporablja se za materiale v obliki praška, granul ali peletov, pripravljene za običajno uporabo, in materiale, nespremenjene ali spremenjene z barvili, aditivi, polnili itd.
Materiali z enako oznako nimajo nujno tudi enakih lastnosti. Ta dokument ne podaja tehničnih podatkov, podatkov o delovanju ali podatkov o pogojih obdelave, ki so morda potrebni za določitev materiala za določeno uporabo in/ali metodo obdelave. Če so take dodatne lastnosti zahtevane, se določijo v skladu s preskusnimi metodami, določenimi v standardu ISO 20558‑2, če je to primerno.
Zahteve za določanje plastomernega materiala za določeno uporabo ali zagotavljanje ponovljive obdelave so podane v podatkovnem bloku 5 (glej točko 4.1).

General Information

• Status: Published
• Public Enquiry End Date: 31-Dec-2018
• Publication Date: 03-Apr-2019
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 28-Mar-2019
• Due Date: 02-Jun-2019
• Completion Date: 04-Apr-2019
• Ref Project: EN ISO 20558-1:2019 - Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 20558-1:2018)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 20558-1:2019
01-maj-2019
3ROLPHUQLPDWHULDOL0DWHULDOLQDRVQRYLSROLIHQLOHQVXOILGD336]DREOLNRYDQMHLQ
HNVWUXGLUDQMHGHO6LVWHPR]QDþHYDQMDLQSRGODJH]DVSHFLILNDFLMH,62

Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 1:
Designation system and basis for specifications (ISO 20558-1:2018)
Kunststoffe - Polyphenylensulfid (PPS)-Werkstoffe - Teil 1: Bezeichnungssystem und
Basis für Spezifikationen (ISO 20558-1:2018)
Plastiques - Matériaux pour moulage et extrusion en poly(phénylène sulfide) (PPS) -
Partie 1: Système de désignation et base de spécification (ISO 20558-1:2018)
Ta slovenski standard je istoveten z: EN ISO 20558-1:2019
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 20558-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 20558-1:2019

---------------------- Page: 2 ----------------------

SIST EN ISO 20558-1:2019


EN ISO 20558-1
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2019
EUROPÄISCHE NORM
ICS 83.080.20
English Version

Plastics - Poly(phenylene sulfide) (PPS) moulding and
extrusion materials - Part 1: Designation system and basis
for specifications (ISO 20558-1:2018)
Plastiques - Matériaux pour moulage et extrusion en Kunststoffe - Polyphenylensulfid (PPS)-Werkstoffe -
poly(phénylène sulfide) (PPS) - Partie 1: Système de Teil 1: Bezeichnungssystem und Basis für
désignation et base de spécification (ISO 20558- Spezifikationen (ISO 20558-1:2018)
1:2018)
This European Standard was approved by CEN on 27 February 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20558-1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 20558-1:2019
EN ISO 20558-1:2019 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 20558-1:2019
EN ISO 20558-1:2019 (E)
European foreword
The text of ISO 20558-1:2018 has been prepared by Technical Committee ISO/TC 61 "Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 20558-1:2019
by Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2019, and conflicting national standards
shall be withdrawn at the latest by September 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 20558-1:2018 has been approved by CEN as EN ISO 20558-1:2019 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 20558-1:2019

---------------------- Page: 6 ----------------------

SIST EN ISO 20558-1:2019
INTERNATIONAL ISO
STANDARD 20558-1
First edition
2018-04
Plastics — Poly(phenylene sulfide)
(PPS) moulding and extrusion
materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Matériaux pour moulage et extrusion en poly(phénylène
sulfide) (PPS) —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 20558-1:2018(E)
©
ISO 2018

---------------------- Page: 7 ----------------------

SIST EN ISO 20558-1:2019
ISO 20558-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 20558-1:2019
ISO 20558-1:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Designation system . 2
4.1 General . 2
4.2 Data block 1 . 2
4.3 Data block 2 . 2
4.4 Data block 3 . 3
4.5 Data block 4 . 4
4.5.1 General. 4
4.5.2 Melt mass-flow rate (MFR) or melt viscosity (MV) . 4
4.5.3 Density . 5
4.5.4 Tensile modulus . 5
4.6 Data block 5 . 6
5  Examples of designations . 6
5.1 Designation only . 6
5.2 Designation transformed into a specification . 7
© ISO 2018 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 20558-1:2019
ISO 20558-1:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This first edition of ISO 20558-1 cancels and replaces ISO 28078-1:2009, which has been technically
revised to introduce a new designation system.
The revised designation system is published under a new ISO number, as many existing documents
refer to ISO 28078-1. If the existing ISO 28078-1 would be replaced by the new designation system,
these documents would refer to the incorrect designation system.
In order to give users time to switch from ISO 28078-1 to ISO 20558-1 any designation system according
to ISO 28078-1 is to be phased out in 5 to 10 years.
A list of all parts in the ISO 20558 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved

---------------------- Page: 10 ----------------------
...

SLOVENSKI STANDARD
oSIST prEN ISO 20558-1:2018
01-december-2018
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHQDRVQRYL
SROLIHQLOHQVXOILGD336GHO6LVWHPR]QDþHYDQMDLQSRGODJH]DVSHFLILNDFLMH
,62
Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 1:
Designation system and basis for specifications (ISO 20558-1:2018)
Kunststoffe - Polyphenylensulfid (PPS)-Werkstoffe - Teil 1: Bezeichnungssystem und
Basis für Spezifikationen (ISO 20558-1:2018)
Plastiques - Matériaux pour moulage et extrusion en poly(phénylène sulfide) (PPS) -
Partie 1: Système de désignation et base de spécification (ISO 20558-1:2018)
Ta slovenski standard je istoveten z: prEN ISO 20558-1
ICS:
83.080.20 Plastomeri Thermoplastic materials
oSIST prEN ISO 20558-1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 20558-1:2018

---------------------- Page: 2 ----------------------
oSIST prEN ISO 20558-1:2018
INTERNATIONAL ISO
STANDARD 20558-1
First edition
2018-04
Plastics — Poly(phenylene sulfide)
(PPS) moulding and extrusion
materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Matériaux pour moulage et extrusion en poly(phénylène
sulfide) (PPS) —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 20558-1:2018(E)
©
ISO 2018

---------------------- Page: 3 ----------------------
oSIST prEN ISO 20558-1:2018
ISO 20558-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 20558-1:2018
ISO 20558-1:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Designation system . 2
4.1 General . 2
4.2 Data block 1 . 2
4.3 Data block 2 . 2
4.4 Data block 3 . 3
4.5 Data block 4 . 4
4.5.1 General. 4
4.5.2 Melt mass-flow rate (MFR) or melt viscosity (MV) . 4
4.5.3 Density . 5
4.5.4 Tensile modulus . 5
4.6 Data block 5 . 6
5  Examples of designations . 6
5.1 Designation only . 6
5.2 Designation transformed into a specification . 7
© ISO 2018 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 20558-1:2018
ISO 20558-1:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This first edition of ISO 20558-1 cancels and replaces ISO 28078-1:2009, which has been technically
revised to introduce a new designation system.
The revised designation system is published under a new ISO number, as many existing documents
refer to ISO 28078-1. If the existing ISO 28078-1 would be replaced by the new designation system,
these documents would refer to the incorrect designation system.
In order to give users time to switch from ISO 28078-1 to ISO 20558-1 any designation system according
to ISO 28078-1 is to be phased out in 5 to 10 years.
A list of all parts in the ISO 20558 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 20558-1:2018
INTERNATIONAL STANDARD  ISO 20558-1:2018(E)
Plastics — Poly(phenylene sulfide) (PPS) moulding and
extrusion materials —
Part 1:
Designation system and basis for specifications
1 Scope
This document establishes a system of designation for poly(phenylene sulfide) (PPS) thermoplastic
materials, which can be used as the basis for specifications.
The types of poly(phenylene sulfide) (PPS) materials are differentiated from each other by a
classification system based on appropriate levels of the designatory properties
a) melt mass-flow rate or melt viscosity;
b) density;
c) tensile modulus;
and on information about the intended application and/or method of processing, important properties,
additives, colorants, fillers and reinforcing materials.
This document is applicable to all PPS materials. It applies to materials ready for normal use in the form
of powder, granules or pellets and to materials unmodified or modified by colorants, additives, fillers, etc.
It is not intended to imply that materials having the same designation give necessarily the same
performance. This document does not provide engineering data, performance data or data on
processing conditions which can be required to specify a material for a particular application and/or
method of processing. If such additional properties are required, they are intended to be determined in
accordance with the test methods specified in ISO 20558-2, if suitable.
In order to specify a thermoplastic material for a particular application or to ensure reproducible
processing, the requirements are given in data block 5 (see 4.1).
2  Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1043-1, Plastics — Symbols and abbreviated terms — Part 1: Bas
...