SIST EN ISO 8734:2001

Parallel pins, or hardened steel or martensitic stainless steel (Dowel pins) (ISO 8734:1997)

Zylinderstifte aus gehärtetem Stahl und martensitischem nichtrostendem Stahl (ISO 8734:1997)

Diese Internationale Norm beschreibt die Eigenschaften von Zylinderstiften aus Stahl, durchgehärtet oder einsatzgehärtet oder aus martensitischem nichtrostendem Stahl, mit Nenndurchmesser d von 1 mm bis einschließlich 20 mm.

Goupilles cylindriques en acier trempé et en acier inoxydable martensitique (ISO 8734:1997)

La présente Norme internationale prescrit les caractéristiques des goupilles cylindriques trempées à coeur ou cémentées et en acier inoxydable martensitique de diamètre nominal, d, de 1 mm à 20 mm inclus.

Valjasti zatiči, kaljeni ali iz martenzitnega nerjavnega jekla (ISO 8734:1997)

General Information

• Status: Published
• Publication Date: 30-Jun-2001
• ICS: 21.060.50 - Pins, nails
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jul-2001
• Due Date: 01-Jul-2001
• Completion Date: 01-Jul-2001
• Ref Project: EN ISO 8734:1997 - Parallel pins, or hardened steel or martensitic stainless steel (Dowel pins) (ISO 8734:1997)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 8734:2001
01-julij-2001
9DOMDVWL]DWLþLNDOMHQLDOLL]PDUWHQ]LWQHJDQHUMDYQHJDMHNOD,62
Parallel pins, or hardened steel or martensitic stainless steel (Dowel pins) (ISO
8734:1997)
Zylinderstifte aus gehärtetem Stahl und martensitischem nichtrostendem Stahl (ISO
8734:1997)
Goupilles cylindriques en acier trempé et en acier inoxydable martensitique (ISO
8734:1997)
Ta slovenski standard je istoveten z: EN ISO 8734:1997
ICS:
21.060.50 =DWLþLåHEOML Pins, nails
SIST EN ISO 8734:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8734:2001

---------------------- Page: 2 ----------------------

SIST EN ISO 8734:2001

---------------------- Page: 3 ----------------------

SIST EN ISO 8734:2001

---------------------- Page: 4 ----------------------

SIST EN ISO 8734:2001
INTERNATIONAL ISO
STANDARD 8734
Second edition
1997-11-15
Parallel pins, of hardened steel and
martensitic stainless steel (Dowel pins)
Goupilles cylindriques en acier trempé et en acier inoxydable martensitique
A
Reference number
ISO 8734:1997(E)

---------------------- Page: 5 ----------------------

SIST EN ISO 8734:2001
ISO 8734:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 8734 was prepared by Technical Committee
ISO/TC 2, Fasteners.
This second edition cancels and replaces the first edition (ISO 8734:1987),
which has been technically revised.
©  ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii

---------------------- Page: 6 ----------------------

SIST EN ISO 8734:2001
©
INTERNATIONAL STANDARD  ISO ISO 8734:1997(E)
Parallel pins of hardened steel and martensitic stainless steel
(Dowel pins)
1 Scope
This International Standard specifies the characteristics of parallel pins (dowel pins) of steel, through hardened
or case hardened and martensitic stainless steel with nominal diameters, d, from 1 mm to 20 mm inclusive.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent e
...